Mikrotik D-5G-30D3-PA Manual

Mikrotik TV antenne D-5G-30D3-PA

Læs gratis den danske manual til Mikrotik D-5G-30D3-PA (4 sider) i kategorien TV antenne. Denne vejledning er vurderet som hjælpsom af 38 personer og har en gennemsnitlig bedømmelse på 4.3 stjerner ud af 19.5 anmeldelser. Har du et spørgsmål om Mikrotik D-5G-30D3-PA, eller vil du spørge andre brugere om produktet?

Side 1/4
A B C D E
F G H KJ LI
M O Q VT XRN P WU YS
Parabolic Dish
Antenna Feed
Feed Bracket
Back Plate
Alignment Bracket
Pole Bracket
Pole Clamp
Case Holder
RF Cable
Self-Bonding Tape Slice
M10x130 Bolt
Adjusting Mechanism
M6x20 Bolt
M4x12 Bolt
M4 Wing Nut
M4 Serrated Washer
M6 Nut
M6 Washer
M6 Fender Washer
M6 Spring Lock Washer
M10 Square Washer
M10 Jam Nut
M10 Fender Washer
M10 Spring Lock Washer
M10 Nut
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
R
S
T
U
V
W
X
Y
1
1
1
1
1
1
2
1
2
2
4
2
16
4
2
5
20
12
8
16
4
4
4
4
4
ITEM DESCRIPTION QTY
MikroTik Antenna assembly preview
*The preview is valid if a MikroTik RB900 series
outdoor device (sold separately) is installed.
MikroTik Radio
MikroTik Antenna assembly preview back* MikroTik Antenna assembly preview front
MikroTik Antenna D-5G-30D3-PA
Quick setup guide and warranty information
Package contents
Q
T
R
A
D
M
FIG. 1
Installation Guide
0. Items Required
• PH2 Screw Driver10mm Wrench 17mm Wrench
This guide is written to be used with a MikroTik RB900 series outdoor
device (sold separately) •
1. Install Back Plate to Parabolic Dish
Install Back Plate [D] to Parabolic Dish [A] using:
[M] M6x20 Bolt x 8 pcs;
[R] M6 Washer x 8 pcs;
[T] M6 Spring Lock Washer x 8 pcs;
[Q] M6 Nut x 8 pcs.
Important:
Back Plate [D] must be aligned respectively to a bore in the
Parabolic Dish [A] - see Fig. 1;
M6 Nut [Q] tightening torque must be approximately 5 Nm.
2. Install Antenna Feed
Install Antenna Feed [B] to Parabolic Dish [A] using:
[C] Feed Bracket x 1 pc;
[N] M4x12 Bolt x 4 pcs;
[P] M4 Serrated Washer x 4 pcs.
Install grounding fasteners:
[O] M6 Wing Nut x 1 pc;
[P] M4 Serrated Washer x 1 pc.
Important:
Antenna Feed [B] and Feed Bracket [C] must be aligned respectively
to the hole in the Parabolic Dish [A] - see Fig. 2;
• M4x12 Bolt [N] tightening torque must be approximately 2 Nm.
3. Assemble Alignment and Pole Brackets
Assemble Alignment [E] to Pole Bracket [F] using:
[M] M6x20 Bolt x 4 pcs;
[S] M6 Fender Washer x 4 pcs;
[T] M6 Spring Lock Washer x 4 pcs;
[Q] M6 Nut x 4 pcs.
Install Adjusting Mechanism [L] using:
[R] M6 Washer x 2 pcs;
[Q] M6 Nut x 2 pcs.
Important:
• Mount Alignment Mechanism's [L] bolt with larger shank diameter
through the corresponding hole in the Pole Bracket [F] - see Fig. 3;
Secure Alignment Mechanism [L] by tightening M6 Nuts [Q] to
approximately 5 Nm;
Do not tighten other fasteners rmly until step 10.
4. Assemble Brackets to Back Plate
Assemble Alignment [E] and Pole Bracket [F] to Back Plate [D] using:
[M] M6x20 Bolt x 4 pcs;
[S] M6 Fender Washer x 4 pcs;
[T] M6 Spring Lock Washer x 4 pcs;
[Q] M6 Nut x 4 pcs.
Install Adjusting Mechanism [L] using:
[R] M6 Washer x 2 pcs;
[Q] M6 Nut x 2 pcs.
Important:
Mount Alignment Mechanism's [L] bolt with larger shank diameter
through the corresponding hole in the Alignment Bracket [E] - see Fig. 4;
Secure Alignment Mechanism [L] by tightening M6 Nuts [Q] to
approximately 5 Nm;
Do not tighten other fasteners rmly until step 9.
N O P
C B
FIG. 2
TS QEC
LRFM
BOLT WITH
LARGE SHANK
FIG. 3
L
RM
S
T
Q
BOLT WITH
LARGE SHANK
E
F
D
FIG. 4


Produkt Specifikationer

Mærke: Mikrotik
Kategori: TV antenne
Model: D-5G-30D3-PA

Har du brug for hjælp?

Hvis du har brug for hjælp til Mikrotik D-5G-30D3-PA stil et spørgsmål nedenfor, og andre brugere vil svare dig




TV antenne Mikrotik Manualer

TV antenne Manualer

Nyeste TV antenne Manualer

PNI

PNI ML100 Manual

3 Juni 2025
Astrell

Astrell AST808 Manual

26 Marts 2025
Televés

Televés MIRA 5G Manual

27 Februar 2025
Televés

Televés BEXIA 5G Manual

27 Februar 2025
Magnavox

Magnavox MC372 Manual

7 Januar 2025
Magnavox

Magnavox MC347 Manual

7 Januar 2025