Mikrotik NetMetal ac² Manual

Mikrotik Ikke kategoriseret NetMetal ac²

Læs gratis den danske manual til Mikrotik NetMetal ac² (10 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 28 personer og har en gennemsnitlig bedømmelse på 3.8 stjerner ud af 14.5 anmeldelser. Har du et spørgsmål om Mikrotik NetMetal ac², eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/10

NetMetal ac²

NetMetal ac²NetMetal ac²

Safety Warnings

Before you work on any equipment, be aware of the hazards involved with electrical circuitry, and be familiar with standard practices for preventing

accidents.

Ultimate disposal of this product should be handled according to all national laws and regulations.

All installation methods for mounting an access point on any wall surface is subject to the acceptance of local jurisdiction.

The Installation of the equipment must comply with local and national electrical codes.

This product is intended to be mounted outdoors on a pole. Please read the mounting instructions carefully before beginning installation. Failure to use the

correct hardware and configuration or to follow the correct procedures could result in a hazardous situation for people and damage to the system.

Use only the power supply and accessories approved by the manufacturer, and which can be found in the original packaging of this product.

Read the installation instructions before connecting the system to the power source.

We cannot guarantee that no accidents or damage will occur due to the improper use of the device. Please use this product with care and operate at your

own risk!

In the case of device failure, please disconnect it from power. The fastest way to do so is by unplugging the power plug from the power outlet.

It is the customer's responsibility to follow local country regulations, including operation within legal frequency channels, output power, cabling

requirements, and Dynamic Frequency Selection (DFS) requirements. All Mikrotik radio devices must be professionally installed.

This is a class A device. In a domestic environment, this product might cause radio interference in which case the user might be required to take adequate

measures.

Exposure to Radio Frequency Radiation:

Exposure to Radio Frequency Radiation:Exposure to Radio Frequency Radiation:This MikroTik equipment complies with the FCC, IC, and European Union radiation exposure limits set forth for an

uncontrolled environment.This MikroTik device should be installed and operated no closer than 20 centimeters from your body, occupational user, or the

general public.

Quickstart

The configuration is the same as PTP Bridge in AP mode, except that wireless mode is set to ap_bridge for PTMP setups. The router can be accessed

directly using the address. If the device is connected to the network with enabled DHCP server, configured DHCP client on the bridge interface will get the

IP address, that can be used to access the router.

Please follow these quick steps to set up your device:

Open the upper cover (see " ");NetMetal ac²#Removing upper and bottom covers

Connect an external antenna to the SMA connector (see " ");NetMetal ac²#Antenna usage

Open the bottom cover (see " ");NetMetal ac²#Removing upper and bottom covers

Connect your ISP cable to the device, make sure the ISP is allowing hardware change and will issue an automatic IP address;

Connect the device to the power source (see " ");NetMetal ac²#Powering

Open network connections on your PC and search for MikroTik wireless network and connect to it;

The configuration can be done through the wireless network usinga Web browser or configuration tool ;https://mt.lv/winbox

Once connected to the wireless network, open WinBox or Web browser;

The default IP: 192.168.88.1, user name: admin and there is no password (or, for some models, check user and wireless passwords on the

;sticker)

Once logged in, use Check For Update button to update the device to the latest software version, the device must have an active Internet

connection;

Once the device is updated, log in again and choose your country on the left side of the screen in the field "Country", to apply country regulation

settings;

Set antenna gain, depending on the antenna you are using,to ensure that EIRP meets the limit set by the local authorities;

Choose the security type WPA/WPA2 and insert a wireless password;

Set a password for your device,it will be used to login next timeand click Apply Configuration.

Powering

The device accepts power in the following ways:

Ethernet port accepts PoE 802.3af/at 24-57 V DC ;

Direct-input power jack (5.5 mm outside and 2 mm inside, female, pin positive plug) accepts 12-57 V DC.

Connecting to a PoE Adapter:

Connect the Ethernet cable from the device to the PoE+DATA port of the PoE adapter;

Connect an Ethernet cable from your local network (LAN) to the PoE adapter;

Connect the power cord to the adapter, and then plug the power cord into a power outlet.

MikroTik mobile app

Use the MikroTik smartphone app to configure your router in the field, or to apply the most basic initial settings for your MikroTik home access point.

Scan QR code and choose your preferred OS.

Install and open application.

By default, the IP address and user name will be already entered.

Click Connect to establish a connection to your device through a wireless network.

Choose Quick setup and application will guide you through all basic configuration settings in a couple of easy steps.

An advanced menu is available to fully configure all necessary settings.

Removing upper and bottom covers

To remove the upper cover, unscrew two captive screws and slide it off the main body. Do not remove screws completely, when assembling

tightening torque 0.2 Nm.

To remove the bottom cover, release clips for both fasteners and cover will be free to open.

Mounting

The NetMetal ac2 is designed to be used outdoors and mounted on pole or DIN rail.