Mikrotik TG-BT5-OUT Manual

Mikrotik Ikke kategoriseret TG-BT5-OUT

Læs gratis den danske manual til Mikrotik TG-BT5-OUT (8 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 22 personer og har en gennemsnitlig bedømmelse på 4.3 stjerner ud af 11.5 anmeldelser. Har du et spørgsmål om Mikrotik TG-BT5-OUT, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/8

TG-BT5-OUT

TG-BT5-OUTTG-BT5-OUT

TG-BT5-OUT are ready to use Bluetooth Tag with a preinstalled battery. The software manual you can find under each product in the Support and

Downloads sections https://mikrotik.com/products

Outdoor Water Proof IP69k - TG-BT5-OUT

Completely sealed and cast IP69k.

Temperature range -20..+85°C.

Shock absorbing case.

Built-in 550mAh LiMnO2 battery.

Suitable for strapping.

Built-in temperature sensor.

Built-in accelerometer.

Magnet activation.

NFC [Serial number].

CryptoAuthentication [ATECC608A].

Dimensions 38x32x15mm.

BLE 5.2 with .Silabs BG22

Safety Warnings

Before you work on any equipment, be aware of the hazards involved with electrical circuitry, and be familiar with standard practices for preventing

accidents.

Ultimate disposal of this product should be handled according to all national laws and regulations.

All installation methods for mounting an access point on any wall surface is subject to the acceptance of local jurisdiction.

The Installation of the equipment must comply with local and national electrical codes.

This product is intended to be mounted outdoors on a pole. Failure to use the correct hardware and configuration or to follow the correct procedures could

result in a hazardous situation for people and damage to the system.

Use only the power supply and accessories approved by the manufacturer, and which can be found in the original packaging of this product.

We cannot guarantee that no accidents or damage will occur due to the improper use of the device. Please use this product with care and operate at your

own risk!

In the case of device failure, please disconnect it from power. The fastest way to do so is by unplugging the power plug from the power outlet.

It is the customer's responsibility to follow local country regulations, including operation within legal frequency channels, output power, cabling

requirements, and Dynamic Frequency Selection (DFS) requirements. All Mikrotik radio devices must be professionally installed.

Exposure to Radio Frequency Radiation:

Exposure to Radio Frequency Radiation:Exposure to Radio Frequency Radiation:This MikroTik equipment complies with the FCC, IC, and European Union radiation exposure limits set forth for an

uncontrolled environment.This MikroTik device should be installed and operated no closer than 20 centimeters from your body, occupational user, or the

general public.

Overview

TG-BT5-OUT is a new addition to our MikroTik equipment. It is a Bluetooth tag (a very small gadget) that can be attached to other equipment or other

belonging. Bluetooth tags play a big role in IoT topologies, where Bluetooth is used to broadcast the data over short distances. Once installed and

configured, the tag will broadcast advertising packets in (default packet format) to the gateway (for example, iBeacon, Eddystone, or Mikrotik telemetry KN

). Gateway, on the other hand, pushes the advertising packet payload to the remote server utilizing or HTTP protocols.OT MQTT

Tag modes

When the product arrives from manufacturing it is set into factory sleep mode. In this mode, all components are shut-down as much as possible and MCU

is put into the deepest sleep state. The current draw is reduced to a minimum, so this is the preferred mode to use when the tag is stored and/or not in use.

To exit this mode put a magnet to the tag's edge (where the switch icon is) and hold it for 3-10 seconds until LED turns off. After that, the tags exits sleep

mode and enters advertising mode.

In the Advertising mode, the tag will broadcast Bluetooth advertising packets. By default, MikroTik's advertisement packets are sent once every 5 seconds.

This can be changed in the Configuration mode.

Configuration mode can be entered only from advertising mode by applying a magnet to the same switch icon as in the exiting factory sleep procedure.

After applying a magnet for 5-10 seconds LED will turn off and the tag enters configuration mode. If you apply a magnet for longer than 15 seconds or

won't connect to the tag with the configuration app, it will go back into advertising mode.

When the device wakes from the factory sleep for the first time, it has this default configuration:

Configuration parameter

Configuration parameterConfiguration parameter Setting/value

Setting/value

Setting/valueSetting/value

Advertising packet format MikroTik

Advertising interval 5.0 seconds

Angle Threshold/Tilt trigger 60°

Freefall Threshold/Accelerometer trigger 156.25 mg

Wakeup Threshold/Wakeup trigger 1.0 mg

Bandwith Filter 0.8 Hz

Low noise filter disabled

Tx Power 4 dBm

The magnet is used on the reed switch to change the tag's operating modes as described above. As soon as the magnet is detected (the reed switch is

activated), the LED will start flashing for the next 5 seconds (first 5 seconds) and, then, stop. It can help you identify that 5 seconds have passed and that

you can remove the magnet to enter configuration mode.

Produkt Specifikationer

Mærke:	Mikrotik
Kategori:	Ikke kategoriseret
Model:	TG-BT5-OUT
Kode for international beskyttelse (IP):	IP69K
Bredde:	38 mm
Dybde:	32 mm
Højde:	16 mm
Vægt:	27 g
Antal pr. pakke:	1 stk
Produktfarve:	Hvid
Near Field Communication (NFC):	Ja
Grænseflade:	Bluetooth