NuTone 744NT Manual

NuTone Ventilator 744NT

Læs gratis den danske manual til NuTone 744NT (2 sider) i kategorien Ventilator. Denne vejledning er vurderet som hjælpsom af 37 personer og har en gennemsnitlig bedømmelse på 4.6 stjerner ud af 19 anmeldelser. Har du et spørgsmål om NuTone 744NT, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

Models 744 / 744NT Recessed Fan / Light

READ AND SAVE THESE INSTRUCTIONS

WARNING

TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO

PERSONS, OBSERVE THE FOLLOWING:

1. Use this unit only in the manner intended by the manufacturer. If

you have questions, contact the manufacturer at the address or

telephone number listed in the warranty.

2. Before servicing or cleaning unit, switch power off at service panel

and lock the service disconnecting means to prevent power from

being switched on accidentally. When the service disconnecting

means cannot be locked, securely fasten a prominent warning

device, such as a tag, to the service panel.

3. Installation work and electrical wiring must be done by a qualiﬁ ed

person(s) in accordance with all applicable codes and standards,

including ﬁ re-rated construction codes and standards.

4. Sufﬁ cient air is needed for proper combustion and exhausting of

gases through the ﬂ ue (chimney) of fuel burning equipment to

prevent backdrafting. Follow the heating equipment manufacturer’s

guideline and safety standards such as those published by the

National Fire Protection Association (NFPA), and the American

Society for Heating, Refrigeration and Air Conditioning Engineers

(ASHRAE), and the local code authorities.

5. When cutting or drilling into wall or ceiling, do not damage

electrical wiring and other hidden utilities.

6. Ducted fans must always be vented to the outdoors.

7. If this unit is to be installed over a tub or shower, it must be

marked as appropriate for the application and be connected to a

GFCI (Ground Fault Interrupter) - protected branch circuit.

8. Never place a switch where it can be reached from a tub or shower.

9. Install this unit in a ﬂ at ceiling only.

10. For use in non ﬁ re rated installations only.

11. Not for use in environmental air handling spaces.

12. CAUTION - RISK OF FIRE AND PERSONAL INJURY: 75W

MAX. LAMP. Use R30, BR30, PAR30L, or PAR30LN lamps only

(75W Max.). For wet locations (tub or shower) - use PAR30L or

PAR30LN (75W Max.) lamp only. Use no other lamp types. Do

not install a lamp indentiﬁ ed for use only in enclosed luminaries.

13. Do not install in a ceiling thermally insulated to a value greater

than R60.

14. This unit must be grounded.

CAUTION

1. For general ventilating use only. Do not use to exhaust hazardous

or explosive materials and vapors.

2. To avoid motor bearing damage and noisy and/or unbalanced

impellers, use the cardboard protector (provided) to keep drywall

spray, construction dust, etc. off power unit.

3. Please read speciﬁ cation label on product for further information

and requirements.

To clean trim ring / baf e: Vacuum with a soft brush attachment or

remove trim ring / bafﬂ e and clean with a soft cloth and mild soap

or detergent. Dry thoroughly before reinstalling.

To clean inside of housing: Remove trim ring / bafﬂ e and vacuum

inside of housing with a soft brush attachment.

OPERATION

The fan and light can be operated using various combinations of on/

off switches and timer controls:

• Fan and light controlled with single on/off switch

• Fan and light controlled with separate on/off switches

• Fan controlled with on/off switch - light with dimmer switch

• Fan controlled with timer control

Do not use a speed control to operate the fan in this unit.

See “Connect Wiring” section for various wiring options.

CLEANING

MAINTENANCE

Motor is permanently lubricated. Do not oil or disassemble motor.

See “Service Parts” section for a list and illustrations of service parts.

Two of the most common ways to connect ductwork to the unit.

HOUSING

MOUNTING

BRACKET

CEILING

JOIST

POWER

CABLE

TRIM RING / BAFFLE

FINISHED CEILING

4" ROUND

DAMPER/DUCT

CONNECTOR

PLAN THE INSTALLATION

The unit can

be installed

anywhere

between ceiling

joists using

mounting

brackets

provided.

Install in a ﬂ at

ceiling only.

Typical Installation

Ducting has a strong effect on the air ﬂ ow, noise and energy use of

the fan. Use the shortest, straighest duct routing possible for best

performance, and avoid installing the fan with smaller ducts than

recommended. Insulation around the ducts can reduce energy loss

and inhibit mold growth. Fans installed with existing ducts may not

achieve their rated airﬂ ow. The unit will operate most quietly and

efﬁ ciently when located where the shortest possible duct run and

minimum number of elbows will be needed.

Plan to supply the unit with proper line voltage and appropriate power cable.

ROOF CAP **

4-IN. ROUND

ELBOW

4-IN. ROUND

DUCT **

WALL

CAP

** Purchase separately

INSTALLATION

2. Mark mounting location.

Position unit between joists and extend mounting brackets.

IMPORTANT: Position brackets so there will be an 1/8” gap

between bottom of housing and ceiling material. Mark the top of

keyhole slot on all four mounting brackets.

COOKING AREA

Do not install above

or inside this area

Cooking

Equipment

Floor

The unit must not

be installed above or

inside the cooking

area shown.

Do not install in a cooking area.

1/8" GAP

1. Install mounting brackets.

Slide the adjustable mounting brackets into the bracket channels

on the housing.

Bend the tabs on the cardboard protector and insert protector into

opening in housing.

NOTE: The cardboard protector shields the inside of the housing

from drywall spray and construction dust. Do not remove it until

after construction is completed.

CARDBOARD PROTECTOR

Statement, or to order Service Parts: go to www.broan-nutone.com

and type the Model in the “Model Search” ﬁ eld at the top of the page.

Broan-NuTone LLC, 926 West State Street, Hartford, Wisconsin, USA

53027 800-558-1711

3. Pound in nails.

Remove unit temporarily, and pound

nails partially into joists at all four

marked locations.

4. Hang and secure housing.

Hang unit from nails. Check to make

sure that there will be a 1/8” gap

between bottom of housing and

ceiling material. Pound nails tight.

For wide joist centers: A #8 x 3/8

self-tapping screw can be used to

join extended brackets together and

create a rigid mount. To ensure a

noise-free mount, crimp the bracket

channels tightly around mounting

brackets.

5. Attach damper/duct connector.

Snap the damper/duct connector onto housing. Make sure that

tabs on the connector lock in housing slots. (Top of damper/duct

connector will be ﬂ ush with top of housing.) Install ductwork.

FLUSH

NOTE: Make sure damper ﬂ ap is in

place inside of duct connector. If it

is not: Squeeze top and bottom of

connector to snap ﬂ ap back into

place.

Fan operated with separate on/off switch or timer.

Light operated with separate on/off switch

or dimmer switch.

7. Connect wiring.

Unit can be wired from outside of housing as shown. Use UL approved

connectors to wire per local codes.

Fan and Light operated with single on/off switch

WIRING PLATE

WHITE

BLUE (FAN)

BLACK

TOP / BACK

OF HOUSING

3-WIRE PLUS

GROUND

POWER

CABLE

GROUND TO

WIRING PLATE

RED (LAMP) TO RED

WIRING PLATE

WHITE

BLUE AND RED

TO BLACK

TOP / BACK

OF HOUSING

2-WIRE PLUS

GROUND

POWER

CABLE

GROUND TO

WIRING PLATE

6. Choose power cable direction.

Remove wiring plate. When re-attached, the wiring plate allows the

power cable to enter unit horizontally or vertically.

HORIZONTAL POWER

CABLE CONNECTION

VERTICAL

POWER CABLE

CONNECTION

1102397B

9. Attach trim ring / baf e to housing.

Remove the cardboard protector from inside the housing collar.

Insert one end of each spring into the holes on the lamp bracket.

Center trim ring / bafﬂ e in ceiling opening.

10. Install bulb.

CAUTION - RISK OF

FIRE: 75W MAX. LAMP

Use R30, BR30,

PAR30L, or PAR30LN lamps

only (75W Max.).

For wet locations (tub or

shower) - use PAR30L or

PAR30LN (75W Max.) lamp

only. Use no other lamp types.

Do not install a lamp indentiﬁ ed

for use only in enclosed

luminaries.

FINISHED

CEILING

MATERIAL

HOUSING

COLLAR

CLEARANCE

HOLE

SPRINGS

TRIM RING /

BAFFLE

LAMP

BRACKET

8. Finish ceiling.

Cut an opening in ﬁ nished ceiling material for housing collar.

Produkt Specifikationer

Mærke:	NuTone
Kategori:	Ventilator
Model:	744NT

Har du brug for hjælp?

Hvis du har brug for hjælp til NuTone 744NT stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ventilator NuTone Manualer

NuTone QTXN110HL Manual

10 September 2025

NuTone 744LEDNT Manual

10 September 2025

NuTone QTRN080L Manual

9 September 2025

5 Juli 2025

5 Juli 2025

5 Juli 2025

4 Juli 2025

4 Juli 2025

4 Juli 2025

4 Juli 2025

Ventilator Manualer

Nyeste Ventilator Manualer

Vaxcel Cromwell F0128 Manual

20 December 2025

Vaxcel Kodiak F0103 Manual

20 December 2025

Broan Flex AE80SL Manual

20 December 2025

Vaxcel Huron F0114 Manual

20 December 2025

Vaxcel F0117 Manual

20 December 2025

Vaxcel Acadia F0132 Manual

20 December 2025

Broan Roomside BEL8 Manual

20 December 2025

JONATHAN Y Joanna JYL9611A Manual

20 December 2025

JONATHAN Y Audie JYL9714B Manual

20 December 2025

Vaxcel Curtiss F0111 Manual

19 December 2025