OttLite Rise Manual

OttLite Lys Rise

Læs gratis den danske manual til OttLite Rise (1 sider) i kategorien Lys. Denne vejledning er vurderet som hjælpsom af 17 personer og har en gennemsnitlig bedømmelse på 4.3 stjerner ud af 9 anmeldelser. Har du et spørgsmål om OttLite Rise, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/1

CONGRATULATIONS!

You’ve purchased the ﬁnest in natural lighting technology with your new OttLite

product.

PRODUCT REGISTRATION FORM

Please complete the enclosed Product Registration Form and return it today by mail, or

WARNING: To prevent electric shock, make sure the lamp is not plugged in until all

steps are complete.

NOTE: THIS UNIT IS FULLY ASSEMBLED

Remove lamp from packing, placing lamp body base (A) ﬂat on a steady surface.

Connect power adapter input (F) into connector (G) in the rear-bottom of the lamp.

3. Plug the power adapter (H) into a standard household 120V AC outlet. Note: Only

use with the supplied power adapter to avoid damage or ﬁre.

4. Power switch (B) is a “touch” switch that controls ON/OFF power, the LED brightness

settings and the color mode function of the lamp.

To power LED settings, slightly touch the switch to achieve the following:

• Turn lamp “ ” to 1st brightness setting; touch the switch “once”;ON

• for 2nd brightness setting; touch the switch “two-times”;

• for 3rd brightness setting; touch the switch “three-times”;

• to turn lamp “ ”; touch the switch “four-times”.OFF

6. This lamp provides three color modes. To adjust lighting color mode slightly “press

and hold” switch (B) for three seconds to switch light color temperature mode;

5000°K, 2700°K, 4000°K.

7. To reposition the light, hold the lamp base (A) steady and grasp either lamp body (C)

or shade (D) depending on needed adjustment.

REFER TO THE FOLLOWING ICON LEGEND FOR CONTROL PANEL (J), AS IT

PERTAINS TO THE INSTRUCTIONS FOR VARIOUS SETTING FUNCTIONS BELOW.

“ ”SETTING BUTTON – to set time and calendar; in alarm mode, push “S” key

to turn off alarm.

M “ ” MODE BUTTON – push to set alarm and snooze

“UP BUTTON” – In setting mode, push to increase.

ˇ – In setting mode, push to decrease. “ ”DOWN BUTTON

CALENDAR AND CLOCK SETTING:

NOTE: Control Panel (J) to set Calendar and Clock is located behind lamp body

(C). NOTE: For clock operation layout and features, see diagram 1.

• Under normal mode, press “ ” to enter setting mode, press SETTING BUTTON

“ ” again for next setting. The sequence of setting is: SETTING BUTTON

HOUR – MINUTE – YEAR – DAY – MONTH. Day of the week changes NOTE:

automatically with date change.

• In setting mode, press

“MODE BUTTON” to quit setting, or it will automatically quit to

normal mode if idle for 60 seconds.

• Under normal mode, press “ ” to switch between “12h” and “24h” displayUP BUTTON

ALARM & SNOOZE FUNCTION SETTING :

• Under normal mode, press “MODE BUTTON” to enter alarm mode.

• Under alarm mode, press “ ” to enter alarm setting, press SETTING BUTTON

“ ” again for next setting, the sequence of setting is: SETTING BUTTON

HOUR – MINUTE – SNOOZE – MUSIC and then exit.

There are 8-music tones to select. NOTE:

• Press “UP BUTTON DOWN BUTTON” and “ ” to adjust alarm time sequence.

•

Under alarm mode, press “UP BUTTON DOWN BUTTON” and “ ” to turn ON/OFF

alarm

and snooze function. “ ” icon will light up on the display to MUSIC NOTE

indicate alarm is set. “ ” will appear on the display to indicate snooze is activated. Zz

Snooze can be set from 1 to 60 minutes.

• When alarm time reached, alarm will ring for 1-minute, then snooze and ring again.

Press “ ” to turn alarm or touch “ ” and “SETTING BUTTON OFF UP BUTTON DOWN

BUTTON” to activate snooze. NOTE : Snooze defaults to 60-minutes, if loss of

power occurs

TEMPERATURE SWITCH SETTING:

• In normal mode, touch “ ” to switch between DOWN BUTTON ºF and ºC display.

SAFETY WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK,

OR INJURY TO PERSONS

1. Turn lamp of f and before handling. WAIT UNTIL LAMP HEAD (D) IS COOL

2. The LED panel (E) might get hot after several hours of continuous use DO NOT place

your hands directly on LED light panel.

3. Never use with an extension cord unless the plug can be fully inserted into the

receptacles in the extension cord.

4. Do not alter the plug.

5. The lamp head included with this unit cannot be replaced by the consumer.

6. INDOOR USE ONLY.

NOTE: The important safety instructions appearing in this instruction sheet are not meant

to cover all possible conditions and situations that may occur. It must be understood that

common sense, caution, and care must be used with any electrical product.

BATTERY REPLACEMENT

• This lamp uses a CR2032 battery. For battery replacement see diagram 2.

Battery compartment (K) is located behind lamp body (C).

• To remove/install button cell battery: use a screwdriver to remove bat tery

compartment door (M). Button cell bat tery is to be installed with the “+” or ﬂat side

facing upward.

BATTERY DISPOSAL:

Battery disposal should be in compliance with local regulations

pertaining to the disposal of hazardous materials. DO NOT INCINERATE.

SAFETY WARNING:

• CAUTION: DO NOT INGEST BATTERY; CHEMICAL BURN HAZARD!

• This lamp contains a coin/button cell battery. If the coin/button cell battery is

swallowed, it can cause severe internal burns in just two hours and can lead to death.

• Keep new and used batteries away from children.

• If the battery compartment does not close securely, stop using the product and

keep it away from children.

• If you think batteries might have been swallowed or placed inside any part of the

body, seek immediate medical attention.

NOTE: Coin/button cell bat teries are small, single cell devices having a diameter

greater than their height.

CAUTION!

IF THE EXTERNAL FLEXIBLE CABLE OR CORD OF THIS LUMINAIRE

IS DAMAGED, IT SHALL BE EXCLUSIVELY REPLACED BY THE MANUFACTURER OR ITS

SERVICE AGENT OR A SIMILAR QUALIFIED PERSON IN ORDER TO AVOID A HAZARD.

CAUTION!

THE LIGHT SOURCE OF THIS LUMINAIRE IS NOT REPLACEABLE; WHEN

THE LIGHT SOURCE REACHES ITS END OF LIFE THE WHOLE LUMINAIRE SHALL BE REPLACED.

CAUTION : Any change or modiﬁcation to product not expressly recognized by Ot tLite

Technologies voids OttLite’s responsibility for proper function of product.

POWER ADAPTER SPECIFICATION:

Input: AC 100-240V, 50/60 Hz, 0.8A Max

Output: 12V DC, 1.5A with a Male DC Plug

THIS LAMP CONTAINS a 5V, 2,1A USB output port (L) located on the bottom rear of

lamp. USB port can charge items such as tablets, cellular phones, etc.

ENGLISH Rise LED Desk Lamp with Digital Display

Rise LED Desk Lamp with Digital Display

CSE13G59 U11B

INS190519 REV090919

CAUTION!

Battery Safety: This

product contains a button

battery. If swallowed, it

could cause severe injury

or death in just 2 hours.

Seek medical attention

immediately.

Diagram 2

Diagram 1

DOWN

SETTING MODE

Produkt Specifikationer

Mærke:	OttLite
Kategori:	Lys
Model:	Rise

Har du brug for hjælp?

Hvis du har brug for hjælp til OttLite Rise stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Lys OttLite Manualer

OttLite CS309G5W Manual

10 Februar 2025

OttLite Covington L1604NK9-SHPR Manual

22 Januar 2025

OttLite Archer L1604BS9-SHPR Manual

22 Januar 2025

OttLite P93009 Manual

22 Januar 2025

OttLite Creative Curves A30009-FFP Manual

12 Januar 2025

OttLite Good Housekeeping Manual

11 November 2024

OttLite Aglow Manual

10 November 2024

OttLite Rise Manual

11 September 2024

OttLite Shine Manual

11 September 2024

OttLite Power Up Manual

11 September 2024

Lys Manualer

Nyeste Lys Manualer

Nitecore MH25 Pro Manual

27 September 2025

Nitecore NWL20 Manual

27 September 2025

Nitecore LR70 Manual

27 September 2025

Nitecore HC65 UHE Manual

27 September 2025

Nitecore MH15 Manual

27 September 2025

Globo 54802S-6 Manual

26 September 2025

LUPO DayledPro 2000 Manual

26 September 2025

DiO 54855 Manual

26 September 2025

Novy Shelf 70013 Manual

26 September 2025

DiO 54736 Manual

26 September 2025