PAC AP4-CH41R2 Manual

PAC Ikke kategoriseret AP4-CH41R2

Læs gratis den danske manual til PAC AP4-CH41R2 (6 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 11 personer og har en gennemsnitlig bedømmelse på 4.3 stjerner ud af 6 anmeldelser. Har du et spørgsmål om PAC AP4-CH41R2, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/6
© 2019 AAMP Global. All rights reserved. PAC is a Power Brand of AAMP Global.
PAC-audio.com
C
Page 1
Rev. V12
Date:092019
Advanced Amplier Interface for
Chrysler / Dodge / Jeep / RAM
AP4-CH41 (R.2)
The AP4-CH41 provides a 6-channel pre-amp output for use with aftermarket audio equipment. Using the full range, xed
level head unit output, in conjunction with CAN messages, the AP4-CH41 delivers a variable 5v RMS pre-amp output
with fading, balance, equalization, and level control capabilities. The module also retains all audio from other vehicle
features such as factory navigation prompts, Bluetooth, uConnect, and parking sensor chimes. A data controlled remote
amplier turn on wire is also provided by the AP4-CH41. When used in conjunction with the APA-TOS1 (sold separately),
the module can provide a variable, stereo, digital audio signal over ber optic (TOSLINK).
Introduction and Features
Important Notes
1. These instructions only apply to R.2.1.3.15 or later revisions of the AP4-CH41
2. Compatible with both amplied and non-amplied factory systems.
• Amplied Vehicles
• Compatible with all data-bus controlled amplied systems, no matter the screen size (including the 12" screen). To identify
these systems, look for logos on door speakers, tweeters, dash speakers or the subwoofer to conrm if the vehicle has an
amplied system (Alpine, Beats or Harman Kardon). Some vehicles may not always have branded systems. Unbranded
amplied systems are generally identied by locating a center channel speaker or subwoofer.
• Non-Amplied Vehicles
• Jeep Wrangler: Compatible with all screen sizes (5”, 7”, and 8”).
• All other models: Only compatible in vehicles equipped with the 7” or 8” screen. Vehicles equipped with the 5” screen
are not compatible.
• If you are installing the AmpPRO in a vehicle that is not equipped with a factory amplier, you must add an amplier to
the vehicle's speakers, as the factory radio will no longer have a 4 channel variable output after it has been re-congured
by the AmpPRO. For example, you can not add only a subwoofer to a non-amplied vehicle, as the radio will no longer
power the cabin speakers properly.
• Non-amplied vehicles equipped with an Active Noise Cancellation (ANC) system require the ANC module to be bypassed.
This can be done manually or with the ANC bypass harness ANC-CH01. The following vehicles have an ANC module
that needs to be bypassed:
• 2019 RAM Truck
• 2017-2019 Pacica
3. If a factory amplier is present, it must remain connected and in the vehicle after the Amp PRO has been installed.
4. The remote output is rated at 2A of current. If more current is needed, an external relay must be used.
5. Channels 5 and 6 are non-fading outputs. The output level of channels 5 and 6 can be controlled using the supplied level
control knob.
6. The chime volume and minimum volume levels are set to 0 dB by default. If you are happy with this level in your particular
application, additional adjustment is not required. Please refer to the Setup and Conguration section on page 2 for more details.
7. The level control knob must be connected in order to manually adjust the chime volume and minimum volume settings.
8. The factory radio's speed controlled volume and surround sound mode are not supported by the AP4 outputs.
9. When using the TOSLINK output (APA-TOS1 sold separately), DIP switch 1 must be on in order for all warning chimes to be
heard through the sound system (see page 2 for details).
10. No adjustments can be made manually using the programming button, or the factory SWC, when the module is connected to
a PC.
Module Layout
LED 1
TOSLINK Output
(APA-TOS1 sold separately)
Front Output
Ch. 1(L) and 2(R)
Rear Output
Ch. 3(L) and 4(R)
Non-Fading Output
Ch. 5(L) and 6(R)
LED 2
Interface Connector 1
Expansion Port
Programming Button
Feature Select
DIP switches
Non-Fading Level Control
Knob Connection
USB Connection

Produkt Specifikationer

Mærke: PAC
Kategori: Ikke kategoriseret
Model: AP4-CH41R2

Har du brug for hjælp?

Hvis du har brug for hjælp til PAC AP4-CH41R2 stil et spørgsmål nedenfor, og andre brugere vil svare dig


Ikke kategoriseret PAC Manualer

PAC

PAC CAM-GM51 Manual

11 Juli 2025
PAC

PAC TY1A-RS Manual

11 Juli 2025
PAC

PAC SR-F15009HX Manual

10 Juli 2025
PAC

PAC SRK-RAM13HX Manual

10 Juli 2025
PAC

PAC AAI-TY3 Manual

30 Juni 2025
PAC

PAC SRK-GM14HX Manual

10 Marts 2025
PAC

PAC C2A-CHY Manual

19 Februar 2025
PAC

PAC MCI-FD22 Manual

19 Februar 2025
PAC

PAC GM6A-RST Manual

19 Februar 2025
PAC

PAC SWI-X Manual

19 Februar 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

WALI

WALI PM-003-W Manual

3 November 2025
Beverage-Air

Beverage-Air Horizon HRP3HC-1HG Manual

3 November 2025
ANCEL

ANCEL FX4000 Manual

3 November 2025
Intermatic

Intermatic OP2GY18 Manual

3 November 2025
Hillvert

Hillvert HI-LJE-111 Manual

3 November 2025
Phoenix Contact

Phoenix Contact AXL F DI32/1 1F Manual

3 November 2025
ANCEL

ANCEL FX3000 ELITE Manual

3 November 2025
Unilux

Unilux NYMPHEA Manual

3 November 2025
MSW

MSW PRO-E 20 Manual

3 November 2025
Ikea

Ikea HOTELLRUM 305.780.28 Manual

3 November 2025