PAC TY1A-RS Manual


Læs gratis den danske manual til PAC TY1A-RS (7 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 2 personer og har en gennemsnitlig bedømmelse på 4.4 stjerner ud af 1.5 anmeldelser. Har du et spørgsmål om PAC TY1A-RS, eller vil du spørge andre brugere om produktet?

Side 1/7
Radio Replacement and
Steering Wheel Control Interface
for Toyota / Lexus / Scion Vehicles
TY1A-RS
© 2019 AAMP Global. All rights reserved. PAC is a Power Brand of AAMP Global.
PAC-audio.com
Pacific Accessory Corporation
Page 1
Rev: V4
Date:090519
Introduction and Features
Important Notes
The TY1A-RS interface allows the replacement of a factory radio in select Toyota/Lexus/Scion vehicles and will retain
factory features such as steering wheel controls (SWC), USB ports (in most cases), AM / FM antenna, and the factory
audio amplier. This interface also allows you to program two radio functions to each SWC button by using short press
long press dual command functionality, and also provides outputs such as: vehicle speed signal (VSS), illumination,
reverse trigger and parking brake.
1. Connection of the OBD connector, with the White / Red and White / Black wires, is not always necessary. Use of these wires
will be dependent on whether or not the aftermarket radio requires specic connections, and whether the vehicle provides these
outputs at the radio. See the “Installation Steps” section starting on page 3 for additional information.
2. Adjustment of the vehicle settings through the original radio’s vehicle settings menu will be disabled after installation of the new
radio. It is advised to make sure all settings are as you desire prior to removal of the original radio.
3. The TY1A-RS does not retain Rear Seat Entertainment.
4. After installation, if you do not initially hear any audio, you may need to cycle the ignition again to initialize the factory amplier.
5. Speaker fading on factory amplied systems is only supported with the “amplied output” connection of the TY1A-RS.
6. When using real time fade, if the fader setting is biased more to the front or rear, as the radio turns on the sound may begin at
the default setting and then quickly transition to your custom setting.
7. Aftermarket radio features such as High Pass Filters (crossovers), DSP or “Network Mode” will interfere with proper fader
function. In order for the TY1A-RS’s fader function to work, the audio from the aftermarket radio’s output must match so it can
compare the front and rear audio levels and determine the proper fader setting for the factory amplier.
8. The USB-TY1 and USB-TY2 are included in order to retain the factory USB port for most (but not all) applications. Please refer
to www.pac-audio.com to see which harness you will need.
9. Best Kit’s part number BAA44 is included for vehicles that require an antenna adapter.
10. The CAM-TY11 or CAM-TY12 must be purchased in order to retain the factory reverse camera. Please refer to
www.pac-
audio.com to see which harness you will need. If the required harness is not available, it is possible to hardwire the
reverse camera using the information provided in Appendix A on Page 7.
Module Layout
Module Status LED
USB Status LED
Interface Connector 1
Expansion Port
Interface Connector 2
Amplied Audio Output
Non-Amplied Audio Output
Programming Button
USB Port
Radio Select DIP switches
Interface Connector 4
Amplied Audio Output Level Adjustment
Radio Replacement and
Steering Wheel Control Interface
for Toyota / Lexus / Scion Vehicles
TY1A-RS
© 2019 AAMP Global. All rights reserved. PAC is a Power Brand of AAMP Global.
PAC-audio.com
Pacific Accessory Corporation
Page 2
Rev: V4
Date:090519
Interface Connectors
Plug Interface Connectors 1, 2 and 4 into the appropriate port on the TY1A-RS interface (using the diagram on page 1 or the
label on the bottom of the TY1A-RS interface). The Connector 3 connection will be dependent upon whether or not the vehicle
has a factory amplied system. Connect to the appropriate port on the TY1A-RS.
Vehicle Connectors
Depending on the application, the
TY1A-RS will need 2 or 3 of the 5
vehicle connectors. The additional
connectors will be left unused on
the harness. Any additional radio
harnesses in the vehicle that do
not plug into one of the vehicle
connectors shown above, will not
be used. Below you will nd the
combinations needed for most
vehicles.
Interface Connector 1
Interface Connector 2
Interface Connector 4
Interface Connector 3
Vehicle Connector 1
Vehicle Connector 2
Vehicle Connector 3
Vehicle Connector 4
Vehicle Connector 5
Combination 1
Typical 2004 to 2013 NON-AMPLIFIED
Vehicle Connector 3 Vehicle Connector 4 Vehicle Connector 5
Combination 2
Typical 2004 to 2013 AMPLIFIED
Vehicle Connector 1 Vehicle Connector 3
Combination 3
Typical 2014 to 2017 AMPLIFIED AND NON-AMPLIFIED
Vehicle Connector 2
Vehicle Connector 4
Vehicle Connector 5
Combination 4
Non-Typical 2012 to 2014 AMPLIFIED
Vehicle Connector 2
Vehicle Connector 1
*OBD-2 V3
*The OBD-2 V3 harness provides
CAN bus from the vehicle to the
TY1A-RS for select vehicles
that do not already provide CAN
bus to the radio. Only use the
OBD-2 V3 if the aftermarket radio
requires connections for Vehicle
Speed Sense, Parking Brake, or
Reverse Signal for the following
applications:
1. Combination 1 from below.
2. Combination 2 from below.


Produkt Specifikationer

Mærke: PAC
Kategori: Ikke kategoriseret
Model: TY1A-RS

Har du brug for hjælp?

Hvis du har brug for hjælp til PAC TY1A-RS stil et spørgsmål nedenfor, og andre brugere vil svare dig




Ikke kategoriseret PAC Manualer

PAC

PAC CAM-GM51 Manual

11 Juli 2025
PAC

PAC TY1A-RS Manual

11 Juli 2025
PAC

PAC SR-F15009HX Manual

10 Juli 2025
PAC

PAC SRK-RAM13HX Manual

10 Juli 2025
PAC

PAC AAI-TY3 Manual

30 Juni 2025
PAC

PAC SRK-GM14HX Manual

10 Marts 2025
PAC

PAC C2A-CHY Manual

19 Februar 2025
PAC

PAC NU-GM4 Manual

19 Februar 2025
PAC

PAC OnStar OS-311b Manual

17 Februar 2025
PAC

PAC BT-SWC-NI1 Manual

11 Februar 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer