PAC RPK4-GM2301 Manual

PAC Ikke kategoriseret RPK4-GM2301

Læs gratis den danske manual til PAC RPK4-GM2301 (12 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 19 personer og har en gennemsnitlig bedømmelse på 4.5 stjerner ud af 10 anmeldelser. Har du et spørgsmål om PAC RPK4-GM2301, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/12

Complete Radio Replacement Kit with

Vehicle Information Retention for

Select 11-Bit GMLAN Vehicles

RPK4-GM2301

P ifi A C ti

Rev. 072517 Page 1

PAC-audio.com

Parts List

The RPK4-GM2301 includes everything you need for a professional installation of an aftermarket radio in your 11-Bit GM

Vehicle.

This kit contains:

1. Dash kit

1a. (x1) Double DIN mounting panel

1b. (x1) Single DIN radio ISO mount trim ring

1c. (x1) LCD adapter bracket (for single DIN applications)

1d. (x1) Pocket (for single DIN applications)

1e. (x8) Radio mounting screws

1f. (x1) USB cover (for when USBDMA1 or USBDMA6 is not used with our kit)

1g. (x2) Radio mounting brackets (one left and one right)

2. Radio replacement interface module

3. Radio connection harnesses

4. PAC-LCD

Overview

The RPK4-GM2301 is a complete radio replacement kit with vehicle information retention for select 11-Bit GMLAN Vehicles. This kit utilizes a

user friendly LCD display with onboard buttons to view and adjust vehicle information and settings. The included radio replacement interface

will retain factory steering wheel controls (SWC) and allows you to program two radio functions to each SWC button by using short press long

press dual command functionality. The interface also provides data bus driven outputs such as retained accessory power (RAP), illumination,

vehicle speed sensor (VSS), reverse trigger and parking brake.

Table of Contents: Page:

1. Factory Radio Removal --------------------------------------------------------- 2

2. Radio Replacement Installation and Wiring Instructions --------------- 3

3. Steering Wheel Control Programming --------------------------------- 3-4

4. Dash Kit Assembly --------------------------------------------------------------- 5

5. Using the PAC-LCD -------------------------------------------------------------- 6

1. If a double DIN radio is being installed with this kit, enough wire has been supplied to mount the LCD in the glove box or center console area.

2. The interface comes pre-programmed for all of the vehicle’s factory SWC functions and does not require programming, unless you wish to

re-assign the SWC functions, or utilize short press long press dual command functionality. The SWC can always be restored to default settings

by pressing and releasing the program button on the side of the interface once and waiting 7 seconds for the LED to ash 3 times.

3. The LED will ash whenever a SWC button is pressed.

4. The Interface has the ability to retain the warning chimes and audible turn signal clicks through its onboard piezo. This feature is on by default.

This can be disabled using the supplied PAC-LCD. For more info on disabling the chimes through the module see page 6.

Important Notes

1a.

1d.

1c.

1b.

1e.

1f.

1g.

Complete Radio Replacement Kit with

Vehicle Information Retention for

Select 11-Bit GMLAN Vehicles

RPK4-GM2301

P ifi A C ti

Rev. 072517 Page 2

PAC-audio.com

Removing the factory radio from the vehicle

2004 - 2007 Chevrolet Malibu / Malibu Max / 2008 Chevrolet Malibu Classic

1. Carefully unclip the thin side trims from both the left and right side of the radio trim bezel.

2. Remove the (2) 9/32 screws from below the driver side under-dash panel.

3. Unclip and remove the side edge panel from the left side of the dash.

4. Remove the (2) 9/32 screws securing the left side of the driver side under-dash panel.

5. Unclip the wire harness from the side trim of the driver’s side under-dash panel.

6. Using a panel removal tool, carefully pry downward on the panel at the bottom of the driver’s side under-dash panel. (There are (3) panel

clips).

7. Using a panel removal tool, unclip the top edge of the driver’s side lower dash panel and lower out of the way.

8. Lower the glove box door all the way down.

9. Remove the single 9/32 screw from the middle of the glove box door latch bar.

10. Remove the (4) 9/32 screws securing the glove box dash section to the sub-dash.

11. Carefully remove the side panel from the right side of the dash.

12. Repeat steps 4 and 5 above for the right side of the dash.

13. Unclip and lower the panel below the glove box and remove the single 9/32 screw from the lower left side of the glove box panel.

Remove the glove box and panel.

14. Starting from the bottom of the radio/HVAC control trim bezel, pull bezel outward to unfasten.

15. Disconnect the hazard harness from the radio/climate control bezel and remove bezel.

16. Loosen the (2) 9/32 screws securing the HVAC controls.

17. Remove the (4) 9/32 screws securing the radio to the sub-dash.

18. Carefully pull radio upward and outward, disconnect the wire harness and antenna lead to remove radio.

2005 - 2006 Chevrolet Cobalt

1. Carefully pop the trim above the glove box with a panel removal tool. Remove trim at the top left of dash bezel.

2. Remove the dash panel with a panel removal tool. Note: Dash panel clips are very tight.

3. Disconnect the wire harness behind dash panel.

4. Remove the (4) 9/32 screws securing the radio to the sub-dash.

5. Carefully pull the radio upward and outward, disconnect the wire harness and antenna lead to remove radio.

2005 - 2009 Pontiac G6

1. Remove side trim panels from both driver and passenger side dash with a panel removal tool.

2. Remove (2) 9/32 screws on both driver and passenger side dash.

3. Remove (3) 9/32 screws from under steering column panel. Remove and set aside.

4. Remove (9) 9/32 screws which hold the glove box assembly in place. Lower the glove box and set aside.

5. Gently remove dash assembly from around radio, unclipping 1 plug located between the vents. Remove (4) 9/32 bolts securing the radio in

place.

6. Remove (2) 9/32 bolts securing heater control assembly in place. Slide the HVAC control assembly forward and remove the factory radio.

Illustration / Schematic

RP4-GM23-HAR

To Aftermarket

Radio

SWC Connection

See above chart for

dierent radio type

connections

Acc On/

Programming

LED

Programming

Button

Produkt Specifikationer

Mærke:	PAC
Kategori:	Ikke kategoriseret
Model:	RPK4-GM2301

Har du brug for hjælp?

Hvis du har brug for hjælp til PAC RPK4-GM2301 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret PAC Manualer

PAC CAM-GM51 Manual

11 Juli 2025

PAC TY1A-RS Manual

11 Juli 2025

PAC SR-F15009HX Manual

10 Juli 2025

PAC SRK-RAM13HX Manual

10 Juli 2025

PAC AAI-TY3 Manual

30 Juni 2025

PAC SRK-GM14HX Manual

10 Marts 2025

19 Februar 2025

19 Februar 2025

19 Februar 2025

19 Februar 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Navman MY500XT Manual

1 August 2025

Navman FOCUS150 GPS Manual

1 August 2025

Scheppach TW1000 Manual

1 August 2025

Navman MiVue 750 WIFI Manual

1 August 2025

Navman MiVue Drive FHD Manual

1 August 2025

Midea MEC64 Manual

1 August 2025

Navman MY50T Manual

1 August 2025

Navman M100 Manual

1 August 2025

Navman MiVue 770 SAFETY Manual

1 August 2025

Navman MiVue 790 Manual

1 August 2025