Panduit CFAPPBL1A Manual
Panduit
Ikke kategoriseret
CFAPPBL1A
Læs gratis den danske manual til Panduit CFAPPBL1A (8 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 7 personer og har en gennemsnitlig bedømmelse på 4.5 stjerner ud af 4 anmeldelser. Har du et spørgsmål om Panduit CFAPPBL1A, eller vil du spørge andre brugere om produktet?
Side 1/8

For Technical Support: www.panduit.com/resources/install_maintain.asp
INSTALLATION INSTRUCTIONS
© Panduit Corp. 2009
FS007A
CONTENTS: (#) indicates FMT2A quantity
OPTICOM QUICKNET Rack Mount Angled Fiber
Cassette Enclosures and Patch Panels
Part Numbers: FMT1A, FMT2A, CFAPPBL1A, CFAPPBL2A
1 - ENCLOSURE
1 (2) - #10-32 x 5/16" SCREWS
4 (5) - #10-32 HEX NUTS
4 - #12-24 x 1/2" SCREWS
4 - M6 x 1 SCREWS
3 - #10 FLAT WASHERS
1 (2) - CABLE ENTRY GROMMET(S)
1 (2) - STRAIN RELIEF BRACKET(S)
2 - ADHESIVE BEVEL ENTRY CLIPS
2 - ADHESIVE BACKED MOUNTS
4 - T
AK-TYs (6" pcs.)
2 - SLACK SPOOLS (FMS1 or FMS2)
Cover (field removable)
Fiber Adapter Panels (FAPs):
Up to 4 for FMT1A
Up to 8 for FMT2A
(sold separately)
Trunk or Interconnect
Cable Entry Grommet
Strain Relief Bracket
Enclosure
CFAPPBL1A
CFAPPBL2A
PG16 Gland
(customer supplied)
1 - CAUTION LABEL
1 - LASER WARNING LABEL
Page 1 of 8
Angled Patch Panel
(CFAPPBL1A shown)
FMT1A
FMT2A
(sold separately)
(sold separately)
ASSEMBLY VIEW showing Fiber Adapter Panels (FAPs) - sold separately
CAUTION:
Fiber optic cable is sensitive to excessive pulling, bending and crushing forces. Consult the manufacturer’s cable specification sheet for
the specific cable in use.
Follow TIA/EIA-568A, 569, 606, and 607 installation guidelines where applicable.
Care should be taken when opening and closing fully loaded drawer in order to protect fiber components.
WARNING: UNMATED CONNECTORS MAY EMIT INVISIBLE LASER RADIATION. DO NOT LOOK DIRECTLY INTO THE END OF THE
CONNECTOR. DO NOT INSPECT WITH MAGNIFYING DEVICES. MAINTAIN CAP ON UNMATED CONNECTORS.

For Technical Support: www.panduit.com/resources/install_maintain.asp
INSTALLATION INSTRUCTIONS
© Panduit Corp. 2009
FS007A
Determine where the cable will enter the
enclosure. Carefully remove the knock-out so as
not to damage the surrounding sheet metal.
DO NOT install the grommet at this stage.
Grommet will be installed after the enclosure is
mounted to the rack.
To remove the cover, unscrew the #10-32 screw,
slide the cover back, lift up and off.
Preparation and Rack Mounting
Figure 3
#10-32 hex nuts and
#10 flat washers
#10-32 screw
Attach the angled patch panel to the enclsoure
with (2) #10 flat washers and (2) #10-32 hex nuts.
Page 2 of 8
Figure 2
Figure 1
Cover
Produkt Specifikationer
Mærke: | Panduit |
Kategori: | Ikke kategoriseret |
Model: | CFAPPBL1A |
Har du brug for hjælp?
Hvis du har brug for hjælp til Panduit CFAPPBL1A stil et spørgsmål nedenfor, og andre brugere vil svare dig
Ikke kategoriseret Panduit Manualer
30 Juni 2025
30 Juni 2025
28 Juni 2025
27 Juni 2025
26 Juni 2025
17 Juni 2025
29 December 2024
29 December 2024
29 December 2024
29 December 2024
Ikke kategoriseret Manualer
- Akrobat
- Zebra
- BlueDri
- Envertech
- Jay-tech
- Meccano
- Edision
- Brother
- Aiphone
- Protector
- Juki
- Arduino
- Ulanzi
- Opus
- Acard
Nyeste Ikke kategoriseret Manualer
3 Juli 2025
3 Juli 2025
3 Juli 2025
3 Juli 2025
3 Juli 2025
3 Juli 2025
3 Juli 2025
3 Juli 2025
3 Juli 2025
3 Juli 2025