Panduit PPTEH Manual

Panduit Ikke kategoriseret PPTEH

Læs gratis den danske manual til Panduit PPTEH (4 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 25 personer og har en gennemsnitlig bedømmelse på 4.5 stjerner ud af 13 anmeldelser. Har du et spørgsmål om Panduit PPTEH, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/4

Page: 1 of 4

PNEUMATIC TOOL OPERATION INSTRUCTIONS

PPTEH PA22213A01

REV: 03 10-2015

PPTEH TENSION

AIR R EQUIRE D: MIN: 80 P SIG (5, 4 ba r)

AIR REQUI RED: M IN: 80 P SIG (5,4 ba r)

M AX: 90 PS IG ( 6,1 ba r)

M AX: 90 P SIG ( 6,1 bar )

1 - 4 5 - 8

H EH

INTRODUCTION

The PPTEH Tool installs Panduit Heavy (H) and Extra Heavy

(EH) cross section cable ties (plastic tie down straps), for

medium to high volume cable tie applications. The tool

pneumatically tensions the cable tie to a tool-controlled

tension, and cuts off the tip.

GENERAL SAFETY PRACTICES

1. Tension Indicator 3. Hose Fitting

2. Selector Knob 4. Trigger

PPTEH Pneumatic Tool

• Only qualified and trained operators should install, adjust or use the pneumatic tool

• DO NOT modify this pneumatic tool. Modifications can reduce the effectiveness of safety measures and increase the risks

to the operator

• DO NOT discard the safety instructions; give them to the operator

• DO NOT use the pneumatic tool if it has been damaged

• Tools shall be inspected periodically to verify that the ratings and markings required by this part of ISO 11148 are legibly

marked on the tool. The employer/user shall contact the manufacturer to obtain replacement marking labels when

necessary

• DO NOT use tool for purposes not intended. Unexpected tool movement or breakage of tool may cause injuries to hand

• Unsuitable postures may not allow counteracting of normal or unexpected movement of the tool

For multiple hazards, read and understand the safety instructions before installing, operating, repairing, main-

taining, changing accessories on, or working near the pneumatic tool.

Safety glasses must be worn at all times by all persons within ten (10) feet of any part of the system.

CAUTION: Be aware of the ejection of cable tie scrap from tool.

DO NOT use tool on live electrical sources.

DO NOT place fingers near gripper during tool actuation. Fingers may be pinched by moving gripper.

DO NOT use tool in an explosive atmosphere.

Ear protection should be worn when operating the tool.

Projectile Hazards:

• Disconnect the pneumatic tool from the energy source when changing inserted tools or accessories

• Always wear impact-resistant eye protection during operation of the tool. The grade of protection required should be

assessed for each use

• Ensure that the workpiece is securely fixed

• Be aware that working on brittle material can cause harmful splinters

TOOL SPECIFICATIONS

Weight: 52 oz. (1474 gr.)

Dimensions*: 11.6” (294mm) Long X 8.6” (218mm) High

*Dimensions in parentheses are metric; all dimensions are

approximate, and for reference only.

• For multiple hazards, read and understand the safety

instructions before installing, operating, repairing,

maintaining, changing accessories on, or working near the

pneumatic tool. Failure to do so can result in serious

bodily injury.

Page: 2 of 4

OPERATION

1. Reading the selector knob from the bottom of the tool, flip the knob to

select the cross section of cable ties to be installed:

H: Approx. 0.30" (7,6 mm) and 0.35" (8,9 mm) wide cable ties

EH: Approx. 0.50" (12,7 mm) wide cable ties

If necessary, further adjust tension per Tension Adjustment

instructions below.

2. Loop cable tie around bundle and insert the tip through the head. Pull

the tie up snug on the bundle by hand.

3. Insert the strap of the cable tie into the side of the tool. With the nose

of the tool flush to the cable tie head, squeeze the trigger to tighten the

cable tie. Typically, only one depression of trigger is necessary for

cable tie cut-off.

SETUP

1. Connect 1/8” NPT male fitting of PPH10 Air Supply Hose to 1/8” NPT female port of PL289N1 Filter/Regulator.

2. Connect 1/8” female quick disconnect socket end of Air Supply Hose to 1/8” male quick disconnect plug at end of PPTEH

Tool.

3. Connect filter/regulator to main NON-LUBRICATED air supply and set regulator at 85 PSIG (5,9 bar). See Air Supply

specifications on Page 3.

Operating Hazards:

• Use of the tool may expose the operator’s hands to hazards, including impacts, cuts, abrasions and heat; wear

suitable gloves to protect hands

• Operators and maintenance personnel shall be physically able to handle the bulk, weight and power of the tool

• Hold the tool correctly; re ready to counteract normal or sudden movements and have both hands available

• Maintain a balanced body position and secure footing; avoid awkward or off-balanced postures, change posture during

extended tasks; this can help avoid discomfort and fatigue

• Use only lubricants recommended by the manufacturer

• Be aware of the risk of a whipping compressed air hose

Repetitive Motion Hazards:

• When using a pneumatic tool to perform work-related activities, the operator can experience discomfort in the hands, arms

shoulders, neck or other parts of the body

• While using a pneumatic tool, the operator should adopt a comfortable posture while maintaining secure footing and avoid-

ing awkward or off-balance postures. The operator should change posture during extended tasks; this can help avoid

discomfort and fatigue

• If the operator experiences symptoms such as persistent or recurring discomfort, pain, throbbing, aching, tingling,

numbness, burning sensations or stiffness; these warning signs should not be ignored. The operator should tell the

employer and consult a qualified health professional

Workplace Hazards:

• Slips, trips and falls are major causes of workplace injury. Be aware of slippery surfaces caused by use of the tool and also

of trip hazards caused by the air line or hydraulic hose

• Proceed with care in unfamiliar surroundings. There can be hidden hazards, such as electricity or other utility lines

• Ensure that there are no electrical cables, gas pipes, etc., which can cause a hazard if damaged by use of the tool

Additional Safety Instructions:

• Air under pressure can cause severe injury. Always shut off air supply, drain hose of air pressure and disconnect tool from

air supply when not in use, before changing accessories or when making repairs

• Whipping hoses can cause severe injury. Always check for damaged or loose hoses and fittings

• DO NOT exceed the maximum air pressure stated on the tool

• Never carry a pneumatic tool by the hose

Periodic Maintenance:

Make sure tool is clean before each use.

Produkt Specifikationer

Mærke:	Panduit
Kategori:	Ikke kategoriseret
Model:	PPTEH

Har du brug for hjælp?

Hvis du har brug for hjælp til Panduit PPTEH stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Panduit Manualer

Panduit C2CAC06ABWPAB1 Manual

2 September 2025

Panduit MIW094 Manual

2 September 2025

Panduit MIW125 Manual

2 September 2025

Panduit PES400 Manual

2 September 2025

Panduit CUCGF06DPW1 Manual

2 September 2025

Panduit CUEFRCKITW1 Manual

2 September 2025

Panduit MIM125 Manual

2 September 2025

Panduit CUSREORCPB1 Manual

2 September 2025

Panduit VS2-AVT-3IB Manual

27 August 2025

Panduit VS-AVT-C08-L10 Manual

27 August 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Turbo Air TBC-65SB-N6 Manual

2 September 2025

Speco Technologies N4WNRMM Manual

2 September 2025

Fromm & Starck STAR_FR_04 Manual

2 September 2025

XPower BR-282A Manual

2 September 2025

Grunkel SAN-GRILLNG Manual

2 September 2025

Phoenix Contact BL2 PPC AIO65 7000 Manual

2 September 2025

AVer DL10 Manual

2 September 2025

Rigol HDO1204 Manual

2 September 2025

XPower A-2B Manual

2 September 2025

Horizon Micro FCJJ-44 Manual

2 September 2025