Qazqa 44964 Manual

Qazqa Lettelse 44964

Læs gratis den danske manual til Qazqa 44964 (2 sider) i kategorien Lettelse. Denne vejledning er vurderet som hjælpsom af 5 personer og har en gennemsnitlig bedømmelse på 4.9 stjerner ud af 3 anmeldelser. Har du et spørgsmål om Qazqa 44964, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

INSTRUCTION MANUAL

These instructions are for your safety. Please read through them thoroughly prior to installation and

retain them for future reference.

Warnings

 This product is Class I and must be earthed.

 It is recommended that this fitting is installed by a qualified electrician.

 This fitting should be fitted in accordance with IEE Regulations and the Building Regulations.

 For you safety, switch off at the mains supply before installing or maintaining this fitting. Ensure

other persons cannot restore the electricity supply without you acknowledgement.

 If you are in any doubt, please consult a qualified electrician.

 If replacing an existing fitting, make a note of the connections.

 Always use the correct type and wattage bulb. Never exceed the wattage stated.

 When changing a bulb, always switch off at the mains and allow the old bulb to cool down before

handling. Dispose of used bulbs carefully.

 The bulb and surrounding parts can become extremely hot during use.

 Cable Type - The correct cable must be used for wiring this fitting. We suggest that you use

H05RN-F specification cable (not supplied) which is an outdoor grade, rubber sheathed cable.

Running it inside a plastic conduit (not supplied) should further protect it. Alternatively, if the cable is

to be in an area where it could become damaged, you should use special armoured cable. This type

of cable has a sheath that is strengthened to protect against damage from objects such as garden

tools, lawnmowers etc. The cable must have a minimum cross sectional area of 1.0mm² and

wherever possible, cables should be run horizontally. Bury the cable minimum of 50cm.

 A light fitting should be connected to a lighting circuit protected by a 5-amp fuse, (or 6-amp residual

current device). If a light fitting is to be connected to a ring main, a fused connection unit fitted with a

3-amp fuse should be installed. This product is only suitable for connection to AC 220-240V / 50Hz

supply.

 We always recommend the use of an approved RCD unit.

 Replace any cracked/damaged diffuser immediately-do not use if they are damaged.

 The fitting is suitable to be installed in normally non-accessible areas. The product cannot be

mounted in areas where motor vehicles may circulate, carriageways, parking areas.

 The product has a rated maximum surface temperature of 160 ºC.

 Dangerous voltage! To indicate hazards arising from dangerous voltages.

 We recommend only using the lamp that is with ultraviolet ray filter.

Specifications

Product type: 44964

Rated voltage: AC 220-240V, 50Hz

Source of light: 70W, G12 (included)

Degree of protection: IP67 ＆ IP65

Protection class: I

44964

Produkt Specifikationer

Mærke:	Qazqa
Kategori:	Lettelse
Model:	44964

Har du brug for hjælp?

Hvis du har brug for hjælp til Qazqa 44964 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Lettelse Qazqa Manualer

30 December 2025

24 August 2024

24 August 2024

23 August 2024

Qazqa RLX-1201 Infrared Sensor Instruction Manual

23 August 2024

23 August 2024

23 August 2024

23 August 2024

23 August 2024

23 August 2024

Lettelse Manualer

Nyeste Lettelse Manualer

Dainolite V166-1W Manual

5 April 2025

Dainolite OFE-161P Manual

5 April 2025

Dainolite DMLED10-A-5D Manual

5 April 2025

Dainolite DM1958F Manual

5 April 2025

NUVO Ballerina 60/1265 Manual

4 April 2025

NUVO SF77/196 Manual

4 April 2025

NUVO Ballerina 60/329 Manual

4 April 2025

NUVO Cordello 60/7883 Manual

4 April 2025

NUVO Destin 60/7706 Manual

4 April 2025

NUVO Livingston 60/7669 Manual

4 April 2025