SAB H0551-S Manual

SAB Radiostyret legetøj H0551-S

Læs gratis den danske manual til SAB H0551-S (2 sider) i kategorien Radiostyret legetøj. Denne vejledning er vurderet som hjælpsom af 28 personer og har en gennemsnitlig bedømmelse på 4.3 stjerner ud af 14.5 anmeldelser. Har du et spørgsmål om SAB H0551-S, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

100 mm

H0551_Rev01

Brass Female Connector

(H0549-S)

ESC

Plastic Female ESC

Connector Case A

(H0551-S)

Plastic Female ESC

Connector Case B

(H0551-S)

Before installation, we recommend removing

the lower support (part # H0529).

ESC preparation: We recommend the battery wire length

to be approximately 100 mm.

Solder the two bullet connectors (H0549) as shown.

Try to solder the wires with the least amount

of vertical dimension (Z).

Install the bullet connectors and assemble the plastic housing.

Mount the ESC with zip ties.

Metrix Hex Nylon

Nut M2.5

(HC200-S)

Socket Head Cap

Screws M2.5x18mm

(HC032-S)

The correct use of the Zip-Ties.

Finishing Washer M2.5

(H0255-S)

Code

Name

Quantity

H0255

Finishing Washer M2.5

H0549

Brass Female Connector

H0550

Brass Male Connector

H0551

Plastic Male Battery Connector Case

H0552

Plastic Female ESC Connector Case A

H0553

Plastic Female ESC Connector Case B

H0567

Carbon Fiber Battery Tray

Code

Name

Quantity

HC031

Socket Head Cap Screw M2.5x15mm

HC032

Socket Head Cap Screw M2.5x18mm

HC125

Flat Head Cap Screw M2.5x8mm

HC200

Metrix Hex Nylon Nut M2.5

HA035

Double Side Tape 1mm

HA036

Battery Strap

HA113

400mm Charger Cable

Page 1

[ ]

Female

Connector

(H0549-S)

Battery

Connector Case

(H0551-S)

Prepare the battery wires as shown.

Wires suggested lenght: 60-70mm.

Solder the bullet connectors to the battery.

Insert the bullet connectors in the plastic housing,

you can apply a little heat to the plastic to facilitate

the insertion.

Mount the battery to the tray using double sided tape

and the long Velcro straps included.

Make sure to locate the best position of the battery for

the optimum center of gravity.

To insert the battery, simply align the tray in the slots and slide it all the way until it locks in place.

To remove the battery, simply lift up on the locking lever and pull. ( Look the detail A ).

IMPORTANT:

The battery tray must be inside the slots on both sides!

MAKE SURE THE BATTERY IS LOCKED IN PLACE BEFORE FLIGHT.

CHECK VERY WELL THE BATTERY BLOCK AND THEN TRY TO PULL OUT THE TRAY.

Flat Head Cap

Screws M2.5x8mm

(HC125-S)

Battery Tray

(H0567-S)

Double

Sided Tape

(HA035-S)

Battery Strap

(HA036-S)

DETAIL A

- 2 x Brass Female Connector [H0549-S].

- 1 x Battery Connector Case [H0551-S].

- 1 x Battery Tray [H0567-S].

- 2 x Flat Head Cap M2.5x8 [HC125-S].

- 2 x Double Side Tape 1mm [HA035-S].

- 1 x Battery Strap [HA036-S].

- 2 x Brass Female Connector [H0549-S].

- 2 x Brass Male Connector [H0550-S].

- 1 x Battery Connector Case [H0551-S].

- 1 x ESC Connector Case A [H0552-S].

- 1 x ESC Connector Case B [H0553-S].

- 2 x Flat Head Cap M2.5x8 [HC125-S].

- 2 x Socket Head Cap

Screws M2.5x18mm [HC032-S].

[H0552-S] [H0553-S]

BATTERY BLOCK

Page 2

Produkt Specifikationer

Mærke:	SAB
Kategori:	Radiostyret legetøj
Model:	H0551-S
Type:	Radio-Controlled (RC) Model Parts
Produkttype:	Batteribakke
Normal brug:	Helikopter
Kapabilitet:	Goblin 380
Mærke kompatibilitet:	Goblin Helicopter