Schneider MTN647395 Manual

Schneider Ikke kategoriseret MTN647395

Læs gratis den danske manual til Schneider MTN647395 (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 10 personer og har en gennemsnitlig bedømmelse på 4.6 stjerner ud af 5.5 anmeldelser. Har du et spørgsmål om Schneider MTN647395, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

V6473-562-04 11/21

Switch actuator REG-K/x230/16 with manual mode and current detection© Merten2009V6473-562-0411/21

SpaceLogic KNX

Switch actuator REG-K/x230/16 with

manual mode and current detection

Operating instructions

SpaceLogic KNX

Switch actuator REG-K/2x230/16 with

manual mode and current detection

Art. no. MTN647395

SpaceLogic KNX

Switch actuator REG-K/8x230/16 with

manual mode and current detection

Art. no. MTN647895

SpaceLogic KNX

Switch actuator REG-K/12x230/16

with manual mode and current

detection

Art. no. MTN648495

For your safety

HAZARD OF ELECTRIC SHOCK, EXPLOSION, OR

ARC FLASH

Safe electrical installation must be carried out only by

skilled professionals. Skilled professionals must prove

profound knowledge in the following areas:

• Connecting to installation networks

• Connecting several electrical devices

• Laying electric cables

• Connecting and establishing KNX networks

• Safety standards, local wiring rules and regulations

Failure to follow these instructions will result in

death or serious injury.

RISK OF FATAL INJURY FROM ELECTRIC SHOCK

The output may carry electrical current even when the

load is switched off.

• When working on the device: Always disconnect the

device from the supply by means of the fuse in the in-

coming circuit.

• Even if the manual switch is in the „OFF“ position, a

KNX telegram can switch the connections to being

live at any time. Before working on the device, always

diconnect the fuse in the incoming circuit from the

supply.

Failure to follow these instructions will result in

death or serious injury.

L 2L 1

5 6 7 81 2 3 4

LL 1 2 LL 3 4 LL 5 6 LL 7 8

567891011121234

LL 5 6 LL 7 8 LL 9 10 LL 11 12LL 1 2 LL 3 4

L 2L 1

5 6 7 81 2 3 4

LL 1 2 LL 3 4 LL 5 6 LL 7 8

567891011121234

LL 5 6 LL 7 8 LL 9 10 LL 11 12LL 1 2 LL 3 4

The switch actuator REG-K/x230/16 with manual mode

and current detection (referred to below as the actuator)

can switch

– two loads (MTN647395) or

– eight loads (MTN647895) or

– twelve loads (MTN648495)

via separate, floating make contacts.

You can also manually switch the connected loads with

manual switches on the actuator without bus voltage.

The actuator has a bus coupler. It is installed on a DIN rail

TH 35 according to EN 60715, with the bus connection

made via a bus connecting terminal. It is supplied with

power from the bus voltage. A data rail is not required.

The actuator also has integrated current detection wich

measures the load current of each channel.

ABus connection terminal, max. 4 core pairs

BProgramming LED (red)

CProgramming button

DCable cover

EOperating LED „RUN“ (green)

FManual switch

GScrew terminals

The device may be damaged!

• Always operate the product in compliance with the

specified technical data.

• Do not use the current detection function for applica-

tions relevant to safety.

• Connect only pure ohmic loads to a channel with di-

rect current (DC).

• Only install devices with at least basic insulation next

to the device.

Failure to follow these instruction can result in

equipment damage.

Getting to know the actuator

Connections, displays and operating

elements

L L 2L L 1

KNX

1 2

½CAUTION

Strong magnetic fields can influence the current

measurement. Install devices with a strong mag-

netic field (e.g. wound transformers such as bell

transformers) at least 2 cm away from the actua-

tor.

1Set the actuator onto the DIN rail.

2Connect KNX.

¼WARNING

Risk of death from electric shock. The device

can become damaged.

Safety clearance must be guaranteed in accord-

ance with IEC 60664--1. There must be at least 4

mm between the individual cores of the 230 V

supply cable and the KNX line A.

Mounting the actuator

RISK OF FATAL INJURY FROM ELECTRIC SHOCK

Voltage may be present at the outputs when the mains

voltage is connected to the system.

If subjected to strong vibrations during transportation,

the switch contacts might change to the enabled state.

After connecting the bus voltage, set the relays of the

channels to the position desired simply by switching

„On/Off“ or by changing the manual switch to „OFF“.

Failure to follow these instructions will result in

death or serious injury.

The device may be damaged!

• Protect the switch contacts with a series-connected

16 A circuit breaker.

Failure to follow these instruction can result in

equipment damage.

1 2

3 4

5 mm

230 V

4 mm

Produkt Specifikationer

Mærke:	Schneider
Kategori:	Ikke kategoriseret
Model:	MTN647395

Har du brug for hjælp?

Hvis du har brug for hjælp til Schneider MTN647395 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Schneider Manualer

Schneider TeSys D LR97D25 Manual

5 November 2025

Schneider Homeline HOM250PSPD Manual

4 November 2025

Schneider BC650-RSX761 Manual

7 Oktober 2025

Schneider P8VNTG Manual

1 Oktober 2025

Schneider QCGK3 Manual

1 Oktober 2025

Schneider Altivar 61 VW3A3319 Manual

1 Oktober 2025

Schneider Altivar 312 VZ3V3103 Manual

1 Oktober 2025

Schneider SCTK30 Manual

1 Oktober 2025

Schneider Altivar 71 VW3A7201 Manual

1 Oktober 2025

Schneider OHBS Manual

1 Oktober 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

DS18 VOC8PRO Manual

5 November 2025

Icron Rover 2850 Manual

5 November 2025

Amaran Peak Manual

5 November 2025

WesAudio Timbre Manual

5 November 2025

MuxLab 500800-TX Manual

5 November 2025

Tripp Lite PDUMH30HVATNET Manual

5 November 2025

NeXtime Plug Inn 2610 ZI Manual

5 November 2025

MSI MS-ND82 Manual

5 November 2025

Sonifex Redbox RB-MSP6 Manual

5 November 2025

NeXtime Plug Inn 2610 ZW Manual

5 November 2025