Schneider MTN649202 Manual

Schneider Ikke kategoriseret MTN649202

Læs gratis den danske manual til Schneider MTN649202 (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 48 personer og har en gennemsnitlig bedømmelse på 4.5 stjerner ud af 24.5 anmeldelser. Har du et spørgsmål om Schneider MTN649202, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

DANGER

Risk of fatal injury from electrical current.

All work on the device should only be carried out

by trained and skilled electricians. Observe the

country-specific regulations as well as the valid

KNX guidelines.

½CAUTION

The device could be damaged.

- Only operate the device according to the

specifications stated in the Technical data.

- All devices that are installed next to the actuator

must be equipped with at least basic insulation.

The switch actuator REG-K/2x230/10 with manual mode

(referred to below as the actuator) can switch two

loads via separate, floating make contacts.

You can switch the actuator to manual operation and

check that it works even without ETS programming, and

you can control the connected loads directly at the

actuator in the event of a bus failure.

The actuator has a bus coupler. It is installed on a DIN

rail, with the bus connection made via a bus connecting

terminal. It is supplied with power from the bus voltage.

A data rail is not required.

For your safety

Getting to know the switch actuator

AUnder the cable cover: Bus connecting terminal,

programming button and programming LED (red)

BOperating LED "RUN" (green)

CChannel status LEDs (yellow) for the corresponding

channel

DChannel keys for manual control of the

corresponding channel, only respond when manual

operation is switched on

EChannel terminals for load voltage

FManual operation key "Manual"

GManual operation LED "Manual" (red)

HFlap forward to open

1Set the actuator onto the DIN rail.

2Connect KNX.

WARNING

Risk of fatal injury from electrical current. The

device could become damaged.

Safety clearance must be guaranteed in

accordance with IEC 60664-1. There must be at

least 4 mm between the individual cores of the

230 V supply cable and the KNX line.

Connections, displays and operating

elements

Mounting the actuator

1 2

5 mm

230 V

4 mm

KNX

DANGER

Risk of fatal injury from electrical current.

Voltage may be present at the outputs when the

mains voltage is connected to the system.

If subjected to strong vibrations during

transportation, the switch contacts might change

to the enabled state.

After connecting the bus voltage, wait 30

seconds. The relays of the channels will be

switched off. Set the relays of the channels to the

position desired simply by switching "On/Off".

3Connect the bus voltage.

4Wait at least 30 seconds.

5Set the relays of the channels to the position

desired simply by switching "On/Off".

½CAUTION

The actuator can be damaged. Protect:

- Connections with a 10-A circuit breaker

connected upstream. If you use separate fuses

for the connections of two related switching

channels, these must be on the same phase.

6Connect the load

7Connect the load voltage.

Now you can check the functionality of the actuator and

the connected loads without having to load the

application from the ETS. (See the "Operating the

actuator" section.)

1Press the programming button.

The programming LED lights up.

2Load the physical address and application into the

device from the ETS.

The programming LED goes out.

The operating LED lights up: The application was loaded

successfully, the device is ready for operation.

Putting the actuator into operation

KNX

10A

L L

1 2 1 2

Switch actuator REG-K/2x230/10 with

manual mode

Operating instructions

Art. no. MTN649202

Produkt Specifikationer

Mærke:	Schneider
Kategori:	Ikke kategoriseret
Model:	MTN649202

Har du brug for hjælp?

Hvis du har brug for hjælp til Schneider MTN649202 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Schneider Manualer

Schneider TeSys D LR97D25 Manual

5 November 2025

Schneider Homeline HOM250PSPD Manual

4 November 2025

Schneider BC650-RSX761 Manual

7 Oktober 2025

Schneider P8VNTG Manual

1 Oktober 2025

Schneider QCGK3 Manual

1 Oktober 2025

Schneider Altivar 61 VW3A3319 Manual

1 Oktober 2025

Schneider Altivar 312 VZ3V3103 Manual

1 Oktober 2025

Schneider SCTK30 Manual

1 Oktober 2025

Schneider Altivar 71 VW3A7201 Manual

1 Oktober 2025

Schneider OHBS Manual

1 Oktober 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

MuxLab 500439 Manual

5 November 2025

GVM BL160-II Manual

5 November 2025

Uniprodo UNI_ROLL_03 2in1 Manual

5 November 2025

Rockville SS6 Manual

5 November 2025

Silk'n VacuPedi FTC04 Manual

5 November 2025

MEPROLIGHT MCO PRO Manual

5 November 2025

XPG Battlecruiser II Manual

5 November 2025

Hosa USQ-110 Manual

5 November 2025

JMAZ Centipede Quadro Manual

5 November 2025

Lake People Mic-Amp F311-D Manual

5 November 2025