Schneider MTN649808 Manual

Schneider Ikke kategoriseret MTN649808

Læs gratis den danske manual til Schneider MTN649808 (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 13 personer og har en gennemsnitlig bedømmelse på 4.5 stjerner ud af 7 anmeldelser. Har du et spørgsmål om Schneider MTN649808, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

The blind actuator REG-K/8x/10 with manual mode

(referred to below as the actuator) can control up to

eight blind/roller shutter drives with limit switch

independently of one another.

You can switch the actuator to manual operation and

check that it works even without ETS programming, and

you can control the connected loads directly at the

actuator in the event of a bus failure.

The actuator has a bus coupler. It is installed on a DIN

rail, with the bus connection made via a bus connecting

terminal. A data rail is not required.

For your safety

HAZARD OF ELECTRIC SHOCK, EXPLOSION, OR

ARC FLASH

Safe electrical installation must be carried out only by

skilled professionals. Skilled professionals must prove

profound knowledge in the following areas:

• Connecting to installation networks

• Connecting several electrical devices

• Laying electric cables

• Connecting and establishing KNX networks

• Safety standards, local wiring rules and regulations

Failure to follow these instructions will result in

death or serious injury.

RISK OF FATAL INJURY FROM ELECTRIC SHOCK

The output may carry electrical current even when the

load is switched off.

• When working on the device: Always disconnect the

device from the supply by means of the fuse in the in-

coming circuit.

• Even if the manual switch is in the „OFF“ position, a

KNX telegram can switch the connections to being

live at any time. Before working on the device, always

diconnect the fuse in the incoming circuit from the

supply.

Failure to follow these instructions will result in

death or serious injury.

The device may be damaged!

• Always operate the product in compliance with the

specified technical data.

• Only connect one motor per channel.

• Only install devices with at least basic insulation next

to the device.

Failure to follow these instruction can result in

equipment damage.

Blind actuator introduction

It is supplied with power both from the bus voltage and

from the mains. This makes three different operating

modes possible:

Bus and mains supply

This is a standard operating mode. The actuator is

supplied by both the bus and mains voltages.

Bus supply only

The actuator is operated solely in bus mode. It can

continue to carry out all functions, but there may be a

slight time delay (e.g. switching of the relays, slat

adjustment). Manual operation is possible.

Mains supply only

It may only be possible to operate the actuator

manually, without bus communication. You can activate

the loads directly using the channel keys.

AMains connection: The actuator has two connecting

terminals each for the N and L cables (looping is

possible).

BUnder the cable cover: Bus connecting terminal,

programming button and programming LED (red)

COperating LED "RUN" (green)

DManual operation LED "Manual" (red)

EManual operation key "Manual"

FChannel terminals for load voltage

GChannel keys for manual control of the

corresponding channel, only respond when manual

operation is switched on

HChannel status LEDs (yellow) for the corresponding

channel

IFlap forward to open

When and how the LEDs light up

1Set the actuator onto the DIN rail.

Connections, displays and operating

elements

Mains and bus voltage

or bus voltage only

mains voltage only

RUN

(green)

On Off

Manual

(red)

during manual

operation

during manual

operation

Channel

(yellow)

during movement during movement

Mounting the actuator

1 2

Hand

L L N N

2Connect KNX.

WARNING

Risk of fatal injury from electrical current. The

device could become damaged.

Safety clearance must be guaranteed in

accordance with IEC 60664-1. There must be at

least 4 mm between the individual cores of the

230 V supply cable and the KNX line.

3Connect the mains voltage.

4Switch on bus/mains voltage.

5Wait at least 30 seconds.

After the bus/mains voltage has been switched on, all

the actuator relays are moved to a predefined position

(factory setting: "Off").

6Connect the load.

7Connect the load voltage.

The device may be damaged!

• Connect the bus connection and the supply voltage

with correct polarity.

• Connect the bus voltage first and only then the load

voltage.

• Connections with a 10 A circuit breaker connected

upstream.

• If the mains voltage is looped, protect the mains con-

nection with a 10 A circuit breaker connected up-

stream as well.

Failure to follow these instruction can result in

equipment damage.

If the toggle times are too short, the blind motor

could be damaged.!

• The toggle time at the factory setting is 500 ms. A

longer toggle time may be necessary for other mo-

tors. Refer to the manufacturer's specifications in the

data sheet for the motor.

Failure to follow these instruction can result in

equipment damage.

1 2

5 mm

230 V

4 mm

KNX

10A

KNX

10A

SpaceLogic KNX

Blind actuator REG-K/8x/10 with manual

mode

Operating instructions

Art. no. MTN649808

Hand

Produkt Specifikationer

Mærke:	Schneider
Kategori:	Ikke kategoriseret
Model:	MTN649808

Har du brug for hjælp?

Hvis du har brug for hjælp til Schneider MTN649808 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Schneider Manualer

Schneider TeSys D LR97D25 Manual

5 November 2025

Schneider Homeline HOM250PSPD Manual

4 November 2025

Schneider BC650-RSX761 Manual

7 Oktober 2025

Schneider P8VNTG Manual

1 Oktober 2025

Schneider QCGK3 Manual

1 Oktober 2025

Schneider Altivar 61 VW3A3319 Manual

1 Oktober 2025

Schneider Altivar 312 VZ3V3103 Manual

1 Oktober 2025

Schneider SCTK30 Manual

1 Oktober 2025

Schneider Altivar 71 VW3A7201 Manual

1 Oktober 2025

Schneider OHBS Manual

1 Oktober 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

DS18 VOC8PRO Manual

5 November 2025

Icron Rover 2850 Manual

5 November 2025

Amaran Peak Manual

5 November 2025

WesAudio Timbre Manual

5 November 2025

MuxLab 500800-TX Manual

5 November 2025

Tripp Lite PDUMH30HVATNET Manual

5 November 2025

NeXtime Plug Inn 2610 ZI Manual

5 November 2025

MSI MS-ND82 Manual

5 November 2025

Sonifex Redbox RB-MSP6 Manual

5 November 2025

NeXtime Plug Inn 2610 ZW Manual

5 November 2025