Stagg ADBA 40 Manual

Stagg Modtager ADBA 40

Læs gratis den danske manual til Stagg ADBA 40 (2 sider) i kategorien Modtager. Denne vejledning er vurderet som hjælpsom af 20 personer og har en gennemsnitlig bedømmelse på 4.5 stjerner ud af 10.5 anmeldelser. Har du et spørgsmål om Stagg ADBA 40, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/2
BACK PANEL:
WARNING: This amplier must be earthed. Please check that the supply voltage details given on the
rating label (located on the rear panel) are in accordance with your electricity supply.
1. POWER SWITCH: This switch turns the amplier on or off.
2. MAINS INPUT: This is the input socket into which the mains power cable must be connected. This
amplier is supplied with a power cable with a moulded-on plug. If the socket outlets in the home are not
suitable for this plug, use an appropriate plug adapter that can handle the power required for the amplier.
3. POWER FUSE: In the event of the power fuse having to be replaced, rst unplug the power cable
from the mains outlet. Then remove the fuse cover and replace the power fuse with another fuse of the
same type and value. Never plug the power cable back into the mains outlet without the fuse cover. If
the power fuse blows up again when powering on the amplier, take the apparatus to a suitable service
centre for repair.
4. CD/MP3 INPUT: This is a line level 1/8” (Ø 3.5 mm) mini stereo jack into which an MP3/CD/Tape
5. LINE OUT: This 1/4” (Ø 6.3 mm) mono jack output can be connected directly to a mixing desk or a
more powerful amplifying system.
6. HEADPHONES: This is a 1/4” (Ø 6.3 mm) standard jack output to connect the headphones. When
headphones are connected, no sound is produced from the speaker.
Features and Specications are subject to change without notice.
FRONT PANEL:
1 MIC INPUT (XLR): Here you can plug in a microphone, using an XLR cable.
2 MIC VOLUME: This control determines the output volume for the microphone channel.
3 INSTRUMENT INPUT: Plug your electric double bass in here, using a 1/4” (Ø 6.3 mm) jack cable. We
recommend that you always use a high-quality shielded cable to prevent any background noise interference
or unwanted feedback.
4 ACTIVE / PASSIVE LATCHING SWITCH: Press or release this switch according to whether your
double bass is active or passive.
5 INSTRUMENT GAIN: This control determines the gain level for the instrument channel.
6 INSTRUMENT COMPRESSION: This control reduces the dynamic range of the output signal and
evens out the changes in volume that occur according to how hard you play or slap your electric double
bass. Adding compression will make your electric double bass smoother and clearer.
7 TREBLE: This control determines the level of high frequencies in the output signal. Adding treble will
make the double bass sound brighter and sharper.
8 MIDDLE: This control determines the level of middle frequencies in the output signal. Adding mid will
make your double bass sound rounder and fuller.
9 PARAMETRIC MIDDLE: Parametric mid is a more sophisticated way of boosting or cutting middle
frequencies. In a traditional EQ, the frequency area that is boosted or cut is xed. With a parametric mid
EQ, this frequency area is adjustable from mid low to mid high. Use this knob to select the required range
of middles, then use knob # to determine the level of the selected range of mid frequencies.8.
10 BASS: This control determines the level of low frequencies in the output signal. Adding bass will make
your double bass sound warmer and heavier.
11 MASTER: This control determines the overall volume of the amplier.
12 POWER LED: Is lit up when the amplier is switched on.
2 3
USER’S MANUALSUSER’S MANUAL ADBA 40 ADBA 40
1 2
1
2
3
4 5 6
3 4 5 6 7 8 9 10 11 12
TECHNICAL SPECIFICATIONS
Max. Rated Power / Loudspeaker 40W RMS @ 8Ω load / 8” Woofer w/ Coaxial Tweeter
Frequency Response 45Hz to 15kHz
Total Harmonic Distortion ≤ 0.8%
Signal to Noise Ratio - 68dB (@ max. Rated Power)
Input Impedance 240Ω (Mic) / 47kΩ (Instrument)
Power Consumption 70W max
Maximum Input Level (Volts RMS) 12mV (Mic) / 72mV (Instrument)
Maximum Gain 72dB (Mic) / 72dB (Instrument)
Dimensions (H x W x D) 38 x 37 x 26cm / 15 x 14.6 x 10.2in.
Weight 12.2kg / 26.9lb
5 5 5 0 0 5 0 5
EQ
MIC
INSTRUME NT
Volume Input
Active/
Passive
Gain Comp Treble Middle Para Mid Bass MasterInput

Produkt Specifikationer

Mærke: Stagg
Kategori: Modtager
Model: ADBA 40

Har du brug for hjælp?

Hvis du har brug for hjælp til Stagg ADBA 40 stil et spørgsmål nedenfor, og andre brugere vil svare dig


Modtager Stagg Manualer

Stagg

Stagg KBA 40 Manual

24 Juni 2025
Stagg

Stagg ADBA 40 Manual

2 Juni 2025

Modtager Manualer

Nyeste Modtager Manualer

Atoll

Atoll AM400 Evolution Manual

8 December 2025
Atoll

Atoll MA100 Manual

8 December 2025
Fostex

Fostex AP25 Manual

7 December 2025
Fostex

Fostex PC200USB-HR Manual

7 December 2025
Atoll

Atoll CD400 Evolution Manual

7 December 2025
Fostex

Fostex PC200USB Manual

7 December 2025
Fostex

Fostex AP05 Manual

6 December 2025
Atoll

Atoll AV500 Manual

6 December 2025
Atoll

Atoll AV100 Manual

5 December 2025
Atoll

Atoll AM300 Evolution Manual

5 December 2025