WyreStorm EX-100-H2-PRO Manual

WyreStorm AV forlænger EX-100-H2-PRO

Læs gratis den danske manual til WyreStorm EX-100-H2-PRO (4 sider) i kategorien AV forlænger. Denne vejledning er vurderet som hjælpsom af 62 personer og har en gennemsnitlig bedømmelse på 4.6 stjerner ud af 31.5 anmeldelser. Har du et spørgsmål om WyreStorm EX-100-H2-PRO, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/4

4K HDR 4:4:4 60Hz HDBaseT™ Extender with DSC

Supporting USB.2.0 Client/host (4K: 100m/328ft)

EX-100-H2-PRO Quickstart Guide

EX-100-H2-PRO v1 Quickstart Guide | 190829

UK: +44 (0) 1793 230 343 | ROW: 844.280.WYRE (9973)

support@wyrestorm.com

1 of 4

WyreStorm recommends reading through this document in its entirety to become familiar with the product’s features prior to starting the

installation process.

Basic Wiring Diagram

HDMI

HDBaseT

Cat6/6a

Ethernet

EX-100-H2-PRO Transmitter (TX)

EX-100-H2-PRO Receiver (RX)

Personal Computer

Wireless Access Point

Isochronous

USB 2.0 Data

USB 2.0 Host

USB

Flash Drive

Short Throw

Projector

Hearing

Induction Loop

12 DC 2A

Power Supply

12 DC 2A

Power Supply

HDMI

Analog Audio

RS-232

Interactive Whiteboard

RS-232 from Control System

KEY

Wireless Router

IMPORTANT! Installation Requirements

• Visit the product page to download the latest rmware, document

versions, additional documentation, and conguration tools.

• Read through the section for important wiring Wiring and Connections

guidelines before creating or choosing premade cables.

• While this product supports CEC, WyreStorm cannot guarantee

compatibility with all forms of CEC communication.

In the Box

1x EX-100-H2-PRO Transmitter (TX)

1x EX-100-H2-PRO Receiver (RX)

1x IR Emitter

1x IR Receiver

2x 3-pin Terminal Block

1x 12V DC 3A Power Supply (US/UK/EU/AU)

4x Mounting Brackets

1x Quickstart Guide (this document)

EX-100-H2-PRO v1 Quickstart Guide | 190829

UK: +44 (0) 1793 230 343 | ROW: 844.280.WYRE (9973)

support@wyrestorm.com

2 of 4

Wiring and Connections

WyreStorm recommends that all wiring for the installation is run and terminated prior to making connections to the switcher. Read through this section in it’s

entirety before running or terminating the wires to ensure proper operation and to avoid damaging equipment.

IMPORTANT! Wiring Guidelines

• The use of patch panels, wall plates, cable extenders, kinks in cables, and

electrical or environmental interference will have an adverse effect on

signal transmission which may limit performance. Steps should be taken

to minimize or remove these factors completely during installation for best

results.

• WyreStorm recommends the use of shielded category cable to minimize

signal noise and interference.

• WyreStorm recommends using pre-terminated HDMI cables due to the

complexity of these connector types. Using pre-terminated cables will

ensure that these connections are accurate and will not interfere with the

performance of the product.

IR TX/RX Guidelines

• Using WyreStorm infrared emitters and receivers is the best way to ensure

that most IR coding formats are transmitted and received Other 3rd party

emitters and receivers can be used; however, these devices must operate in

the same manner as the WyreStorm devices.

• Due to differences in IR across 3rd party control systems their IR ports

should never be connected directly to a WyreStorm system as an

incompatibility may exist. WyreStorm offers a cable that compensates for

voltage differences as well adjusts for differences in the pins used within the

port. Refer to the product page for more information.CAB-IR-LINK

IR TX Port Pinout

Connection for IR TX (transmit) uses a 3.5mm (1/8in) mono plug.

Tip: Anode

Sleeve: Cathode (IR Signal)

IR RX Port Pinout

Connection for IR RX (receive) uses a 3.5mm (1/8in) stereo jack that outputs

+5V DC to power the included IR receiver.

Tip:

Ring: IR Signal

+5V DC

Sleeve: Ground (GND)

Audio Connections

Tip:

Ring:

Left Channel

Right Channel

Sleeve: Ground (GND)

RS-232 Wiring

The EX-100-H2-PRO uses a 3-pin RS-232 with no hardware ow control. Most

control systems and computers are DTE where pin 2 is RX, this can vary from

device to device. Refer to the documentation for the connected device for pin

functionally to ensure that the correct connections can be made.

Refer to for details on setting RS-232 modes.RS-232 Mode Settings

3rd Party Device

Pin 1 TX (Transmit) > To > RX (Receive)--- ---

Pin 2 RX (Receive) > To > TX (Transmit--- ---

Pin 3 G (Gro d) > To > G (Gro d)un --- --- un

WyreStorm Co ectornn

Produkt Specifikationer

Mærke:	WyreStorm
Kategori:	AV forlænger
Model:	EX-100-H2-PRO

Har du brug for hjælp?

Hvis du har brug for hjælp til WyreStorm EX-100-H2-PRO stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

AV forlænger WyreStorm Manualer

WyreStorm EX-70-G2 Manual

27 August 2024

WyreStorm EX-35-H2-ARC Manual

27 August 2024

WyreStorm EX-100-H2-PRO Manual

27 August 2024

WyreStorm RXV-70-4K-G2 Manual

27 August 2024

WyreStorm EXP-EX-80-KVM Manual

27 August 2024

WyreStorm RXV-70-4K-ARC Manual

27 August 2024

WyreStorm NHD-IP-TX Manual

27 August 2024

WyreStorm TX-70-POH Manual

27 August 2024

WyreStorm EX-35-4K Manual

27 August 2024

WyreStorm EX-40-G3 Manual

27 August 2024

AV forlænger Manualer

Nyeste AV forlænger Manualer

Tripp Lite B126-2A0 Manual

31 Juli 2025

Tripp Lite B126-1A1-PLHD Manual

31 Juli 2025

Tripp Lite B013-330 Manual

31 Juli 2025

Tripp Lite B127U-111-PHPH Manual

30 Juli 2025

Tripp Lite B140-101X Manual

30 Juli 2025

Tripp Lite B140-002 Manual

30 Juli 2025

Tripp Lite B140-002-DD Manual

30 Juli 2025

Tripp Lite B130-101-2 Manual

30 Juli 2025

Tripp Lite B127U-002-PDPH2 Manual

30 Juli 2025

Tripp Lite B126-1A1 Manual

30 Juli 2025