WyreStorm TX-70-POH Manual


Læs gratis den danske manual til WyreStorm TX-70-POH (4 sider) i kategorien AV forlænger. Denne vejledning er vurderet som hjælpsom af 9 personer og har en gennemsnitlig bedømmelse på 4.9 stjerner ud af 5 anmeldelser. Har du et spørgsmål om WyreStorm TX-70-POH, eller vil du spørge andre brugere om produktet?

Side 1/4
4K HDMI over HDBaseT Transmitter
with PoH | Bi-directional IR & RS-232 (70m/230ft)
TX-70-POH
Quickstart Guide
In the Box
1x TX-70-POH Transmitter
1x 2-pin Screw Down Phoenix Connector
1x 3-pin Screw Down Phoenix Connector
1x IR Emitter
1x Broadband IR Receiver (30KHz~50KHz)
2x Mounting Brackets
1x Quickstart Guide (this document)
Basic Wiring Diagram
IR
Key
HDMI/Digital Video HDBaseT/Ethernet
TX-70-POH
IR TX to IR Loop
(Required for remote source control)
MX-0808-PP-POH-CUSTOM with TX-POH-100
UHD Source
IMPORTANT!
Do not connect or disconnect (hot plug) the HDMI, or HDBaseT
connections while the transmitter or receiver is powered on. Doing so
may cause damage to the units or connected devices.
Additional Information
This Quickstart Guide provides the basic steps for the common uses of
this product. Refer to the Installation Guide and other documentation on
the product page for additional information.
Recommended Products
To take full advantage of the features of this receiver, WyreStorm
recommends the following products be used within the system.
HDBaseT Matrix Switchers with HDBT In
The TX-70-POH was designed to be work with the HDBT In found on
some WyreStorm matrixes to allow remote devices to be used as a
source.
MX-0808/1616-PP-POH-CUSTOM with TX-POH-100
SW-1001-HDBT
Cable for Connecting to IR Connecting Blocks/Control Systems
When connecting the IR RX to an IR connecting block or control
system, use the WyreStorm CAB-IR-LINK cable to remove the sleeve
+5V DC supplied by the IR Ext/IR RX ports.
Before Beginning
WyreStorm recommends visiting the product page before installing
this product for updates to this Quickstart Guide as well as other
information about the product.
Verify that all items are included in the packaging per the In The Box
list.
Pre Wire
1. Run a Cat5e/6/6a cable from the transmitter location to the matrix/
receiver location. See Supported Video Resolutions for resolution
distance restrictions. Terminate the cable per the HDMI/HDBaseT
Wiring section.
2. (Optional) If using 3rd party IR emitters or connecting blocks, run
the wire and terminate per the IR TX (Emitter) Wiring section.
3. (Optional) If using 3rd party IR receivers, run the wire and terminate
per the IR RX (Receiver) Wiring section.
4. (Optional) If using RS-232 pass-through, run the wire and terminate
per the RS-232 Wiring section.
Transmitter Installation
1. Install the matrix/receiver following the documentation provided
with the product.
2. Connect an HDMI source to the HDMI In on the transmitter using
an HDMI cable from a high quality brand such as WyreStorm
Express.
3. Using the cable created in Pre Wire step 1, connect the 8-pin RJ-45
female plug to the HDBT In jack.
4. (Optional) Using the included IR emitter or the cable created in
Pre Wire step 2, place an IR emitter onto a source device near the
device’s IR sensor. Connect the 3.5mm (1/8in) Mono Plug to an IR
TX port.
5. (Optional) Using an included IR receiver, connect the 3.5mm (1/8in)
Stereo Plug to an IR Ext port. If using a control system, use the
WyreStorm CAB-IR-LINK or the cable created in Pre Wire step 3.
6. (Optional) If using RS-232 pass-through, connect the 3-pin
connector to the RS-232 port on the receiver and the opposite end
to a port on the device being controlled.
Copyright © 2015 WyreStorm Technologies | wyrestorm.com
TX-70-POH Quickstart Guide | 151124
North America: 518-289-1294 | EMEA/ROW: 44 (0) 1793 230 343
support@wyrestorm.com
1 of 4
WyreStorm recommends reading through this document in its entirety to become familiar with the product’s features prior to starting the
installation process.
PoH-Compatible HDBaseT transmitter to send HD Video & Audio 70m/230ft over HDBaseT.


Produkt Specifikationer

Mærke: WyreStorm
Kategori: AV forlænger
Model: TX-70-POH
Type: AV sender
Vekselstrømsindgangsspænding: 100 - 240 V
Vekselstrømsindgangsfrekvens: 50 - 60 Hz
Bredde: 181.7 mm
Dybde: 94 mm
Højde: 18 mm
Vægt: 400 g
Produktfarve: Sort
Understøttede videotilstande: 1080p
3D: Ja
Opbevaringstemperatur (T-T): -20 - 70 °C
Relativ luftfugtighed ved drift (H-H): 10 - 90 %
HDCP: Ja
Understøttede lydformater: PCM
Driftstemperatur (T-T): 0 - 45 °C
Maksimal opløsning: 4096 x 2160 pixel
Understøttede grafikopløsninger: 1920 x 1080 (HD 1080),3840 x 2160,4096 x 2160
Forbindelsesteknologi: Ledningsført
Certificering: CE, FCC
Strømforbrug (maks.): 7.2 W
LED-indikatorer: Ja
Udgangsstrøm: 2 A
Bæredygtighedscertifikater: RoHS
Firmware kan opgraderes: Ja
Maksimal overførselsafstand: 70 m
HSMI-indgang: 1
Opløsning: 4096 x 2160 pixel
Fjernbetjening (IR) indgang: 1
Fjernbetjening (IR) udgang: 1
HDBaseT-port: Ja
Understøttede kabeltyper: Cat6, Cat6a, Cat7
Video indgang: 1
RJ-45 udgangs-porte: 1
HDBaseT certificeret: Ja
Understøtter forbrugerelektronik (CEC): Ja
Driftsspænding (sender): 12 V

Har du brug for hjælp?

Hvis du har brug for hjælp til WyreStorm TX-70-POH stil et spørgsmål nedenfor, og andre brugere vil svare dig




AV forlænger WyreStorm Manualer

AV forlænger Manualer

Nyeste AV forlænger Manualer

EtherWAN

EtherWAN ED3538 Manual

30 Oktober 2025
Kramer

Kramer TP-120-OD Manual

21 Oktober 2025
Kramer

Kramer VM-218DT Manual

17 Oktober 2025
Kramer

Kramer KIT-401 Manual

16 Oktober 2025
Kramer

Kramer TP-580CT Manual

16 Oktober 2025
CYP

CYP PUV-1230PL-KIT Manual

15 Oktober 2025
Smart-AVI

Smart-AVI DVX-RXPROS Manual

13 Oktober 2025
Extron

Extron FOX3 SR 211 Manual

10 Oktober 2025
Extron

Extron FOX3 T 211 Manual

8 Oktober 2025