AFX Evanston EVNP2532LAJUDSN Manual

AFX Lys Evanston EVNP2532LAJUDSN

Læs gratis den danske manual til AFX Evanston EVNP2532LAJUDSN (2 sider) i kategorien Lys. Denne vejledning er vurderet som hjælpsom af 19 personer og har en gennemsnitlig bedømmelse på 4.4 stjerner ud af 10 anmeldelser. Har du et spørgsmål om AFX Evanston EVNP2532LAJUDSN, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

Indoor Luminaire

Evanston Pendant

120~277VAC / 60Hz

Page 1 of 2 8061256 R0

Model EVNP2532LAJUDSN #

Safety Precautions

 Read all safety precautions and installation instructions carefully before installing or servicing this xture. Failure to comply with these instructions could result in

potentially fatal electric shock and/or property damage.

 It is recommended that a qualied electrician perform all wiring. This fixture must be wired in accordance with all national and local electrical codes.

 Do not handle any energized xture or attempt to energize any xture with wet hands or while standing on a wet or damp surface or in water.

 This xture is designed for use in a 120-277VAC, 60Hz fused circuit. The xture is compatible with Triac (forward-phase or leading edge) / ELV (reverse phase or trailing

edge) and 0-10 V dimmers. Make sure that the power source conforms to the requirements of the xture. (See labels on the xture housing).

 To reduce the risk of electrical shock, and to assure proper operation, this xture must be adequately grounded. To accomplish proper grounding, there must be a

separate ground wire (green) contact between this xture and the ground connection of your main power supply panel.

 This xture is intended to be used for general indoor lighting in dry or damp wet locations.

 Disclaimer

Changes or modications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. NOTE: This

equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules and Canadian ICES-005 (B) / NMB-005

(B). These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate

radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no

guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be

determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiver antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.

• Consult with the dealer or an experienced radio/TV technician for help.

Any modications to this xture may void the warranty and interfere with the safe operation of the luminaire.

Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference

that may cause undesired operation of the device.

Assembly Instructions

1. Preparing for installation-

A. before installing or servicing any part of this xture. Disconnect electrical power

B. Remove xture from box. Separate contents of parts bag.

2. Fixture Assembly.

A. Attach xture shade (1) to xture LED pan (2) using 6 provided screws (3). Hand

tighten to make sure they are secured tightly. Do not over tighten and strip threads.

B. Choose desired height for xture stems using any , stems of the 6” 12” & 18”

provided to achieve your preferred hang length to the top of the shade.

C. Feed xture wiring from top of shade up through both stems that are going to be

used all the way through the Hang Straight into the canopy.

D. Starting with the bottom stem thread each stem together one at a time until the

Canopy is securely tightened to the stems.

E. Tighten the stems to the canopy at the three locations with the desired stem lengths

to get the look wanted.

3. Wiring- all wiring must take place inside junction box.

Caution: Make sure power is o at fuse or circuit breaker box. Check power wires for any damage or scrapes. Use wire suitable for at least 90C (194F).

Note: Most dwellings built before 1985 have supply wire rated to 60C. Consult a qualied electrician before installing.

A. ical shock, overheating, low or no light output, and This unit will not operate properly unless connected to a “grounded” electrical circuit. Electr

shortened LED life can result if proper grounding is not done. Securely attach power source ground wire and xture ground wire to green ground

screw on circular mounting bracket.

B. r NEC (National Electrical Code) requirements, cut the co Then remove the ends of the three wires for Fo rd about 7” above the canopy. 3/8” from

connection purposes.

C. . Fixture will operate normally w/o connection to any dimmers. Connect white xture lead to white (N) wire from supply For none-dimming xture

power source. Connect black xture lead to black (L) wire from supply power source. Gray and purple wires are not to be used and must be

individually capped to prevent shorting.

D. Connect white xture lead to (N) wire from dimming source per dimmer wiring instructions. Connect black xture lead to For TRIAC dimming.

black (L) wire from dimmer supply power source. Gray and purple wires are not to be used and must be individually capped to prevent shorting.

E. . Connect gray wire from the xture to the dimmer source gray wire. Connect purple wire from the xture to the For (0-10V) dimming xture

dimmer source purple wire. Connect white xture lead to white (N) wire from supply power source. Connect black xture lead to black (L) wire from

dimmer supply power source.

F. . Pull on each wire lead to make sure connections are secure. Make certain no bare wires are exposed outside of wire Do not mix wires

connectors. Tuck all connections neatly into junction box.

Limited Factory Warranty

AFX Inc. hereby warranty that this xture is free from defects in materials and workmanship when installed and used under normal operating

conditions for a period of 5 years from the date of shipment from the factory. This warranty covers all component parts and extends only to

replacement of defective xture or components: it does not cover failure due to improper installation, misuse, mishandling or damage

incurred in transit.

Produkt Specifikationer

Mærke:	AFX
Kategori:	Lys
Model:	Evanston EVNP2532LAJUDSN

Har du brug for hjælp?

Hvis du har brug for hjælp til AFX Evanston EVNP2532LAJUDSN stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Lys AFX Manualer

AFX RAMV3603L30D1SN Manual

11 December 2025

AFX TPWW70050LWH Manual

10 December 2025

AFX JAXF1515L30D1 Manual

9 December 2025

AFX SADW0518L30D1 Manual

9 December 2025

AFX DAXV2705L30D1 Manual

9 December 2025

AFX Bowen BWNS051412L30D1SB Manual

18 August 2025

AFX Echo ECHP4830LAJMVBK Manual

18 August 2025

AFX LED Security BWSW2400L41RB Manual

18 August 2025

AFX Ion IONS032015L30D2SN Manual

18 August 2025

AFX SPARKLING-PRO Manual

25 Juli 2025

Lys Manualer

Nyeste Lys Manualer

NUVO 65/748 Manual

16 December 2025

NUVO 65/213 Manual

16 December 2025

Dainolite CER-3LEDT Manual

16 December 2025

Alora Belmont PD536107 Manual

16 December 2025

V-TAC VT-ST20CCT Manual

16 December 2025

Dals CFLEDSQ06-CC Manual

16 December 2025

Dals CFLEDR14-CC Manual

16 December 2025

V-TAC VT-11025 Manual

16 December 2025

NUVO 60/6028 Manual

15 December 2025

NUVO 60/6114 Manual

15 December 2025