CRUX RVCVW-73L Manual

CRUX Bakkamera RVCVW-73L

Læs gratis den danske manual til CRUX RVCVW-73L (2 sider) i kategorien Bakkamera. Denne vejledning er vurderet som hjælpsom af 40 personer og har en gennemsnitlig bedømmelse på 4.8 stjerner ud af 20.5 anmeldelser. Har du et spørgsmål om CRUX RVCVW-73L, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

- Codes the factory radio to turn on the reverse camera function.

- OEM type license plate light camera with white LED included.

- Includes camera power down circuit to extend the life of the camera.

- MFD3 or RNS-315 Navigation Radios.

In the event this unit is to be returned for any reason, the customer must “decode”

the radio before doing so to receive a replacement or refund. See instructions on

page 2 on how to decode the radio.

RVCVW-73L

MODULE

RVCVW-73L

HARNESS

OBD II ENCODER

CVW- L 07

CAMERA

POWER DOWN

CIRCUIT

The parking lines are there to assist you while reversing. To activate the parking lines simply

cut/disconnect the WHITE loop wire located near the 4-pin camera connector.

What the Lines mean:

Green Line: CLEAR

Yellow Line: GETTING CLOSE

Red Line: WARNING - VERY CLOSE

rev.020521

1 / 2

GREEN

YELLOW

RED

INSTALLING THE CAMERA AND INTERFACE

1. Open the trunk and find a location that will allow you to access the license plate area.

2. Remove the left side license plate light, disconnect and remove the light bulb from the

assembly.

3. Insert the light bulb into the new license plate light camera housin g.

4. Fish the camera cable through the license plate light and inside the cabin. You may need

to drill a pass through hole if you cannot find one.

5. Prepare to wire the Power Down Circuit provided in the kit. Please see diagram on the

next page for wiring instructions.

6. Place the new license plate light camera housing into the empty slot and snap it in place.

7. Run the camera extension cable along the side of the vehicle towards the radio.

8. Remove the radio to gain access to the factory connectors.

9. Make the power and video connections

Please follow these steps to code the radio for reverse camera option:

1. Close all the doors.

2. Put the key to the ON position. (Do not start the car)

3. Connect the OBD II coder to the OBD II port. vehicle’s

4. Look at the GREEN LED inside the OBD II coder. LED should be solid GREEN.

5. Disconnect the OBD II coder.

6. Turn the key OFF and remove key.

7. Open and close the driver door, then lock the car.

8. Wait for approximately 2 minutes.

9. Start the car, put into reverse gear and confirm if reverse imager is on the screen.

10. Keep the OBD II encoder stored in the vehicle in case the radio would need to be recoded.

To decode the radio, repeat steps above.

The RVC - L module has 2 LEDs on the side of the Molex connector that confirms its VW 73

functionality as follows:

Flashing LEDs = Coding vehicle

Solid GREEN = Activated

Solid RED = Deactivated

Solid RED and GREEN = Error

VOLKSWAGEN

2012 2015 Beetle–

rev.020521

2 / 2

Produkt Specifikationer

Mærke:	CRUX
Kategori:	Bakkamera
Model:	RVCVW-73L

Har du brug for hjælp?

Hvis du har brug for hjælp til CRUX RVCVW-73L stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Bakkamera CRUX Manualer

24 Juli 2025

29 December 2024

29 December 2024

29 December 2024

29 December 2024

CRUX RVCCH-75RC Manual

18 November 2024

CRUX RVCCH-75DC Manual

16 August 2024

CRUX RVCCH-75WTC Manual

15 August 2024

CRUX CNS-03V Manual

15 August 2024

CRUX CVW-07G Manual

15 August 2024

Bakkamera Manualer

Nyeste Bakkamera Manualer

Pyle PLCMTR72 Manual

8 August 2025

Pyle PLCM4590WIR Manual

8 August 2025

Pyle PLCMTR78WIR Manual

8 August 2025

Biltema 43-170 Manual

25 Juli 2025

Rockville RBC-1 Manual

22 Juli 2025

Rockville RBC-5 Manual

22 Juli 2025

Dometic PerfectView CAM 12 Manual

21 Juli 2025

Rockville RBC4 Manual

16 Juli 2025

Rockville RBC2 Manual

16 Juli 2025

Rockville RBC3 Manual

16 Juli 2025