Eliminator Lighting Aqua LED Manual

Eliminator Lighting Ikke kategoriseret Aqua LED

Læs gratis den danske manual til Eliminator Lighting Aqua LED (1 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 3 personer og har en gennemsnitlig bedømmelse på 5.0 stjerner ud af 2 anmeldelser. Har du et spørgsmål om Eliminator Lighting Aqua LED, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/1

AQUA LED

SPECIFICATIONS:

Model: Aqua LED

Supply Voltage: 120V/60Hz

LED: 1 x 10W LED

Power Consumption: 12W

Fuse: 1Amp

Weight: 6 lbs./ 2.7 kgs.

Size: 8” L x 9” W x 9” H

Beam Angle:

Working Position: Any Safe position

Duty Cycle: None

Warranty: 1 Year

CAUTION! Please read and understand

these instructions before installing or oper-

ating this unit.

Introduction and Operation: The unit is ready to be hung or set on flat surface. This fixture is

designed to operate as a stand alone unit. It has been tested at the factory there is no assemand -

bly necessary. The Aqua LED is a rippling water eect. Plug this xture in and it will light right up.

On the rear of the unit there is a toggle switch that is used to control the internal color wheel. When

toggle switch is one position the color wheel will automatically and continuously scroll through the

color wheel. When the color wheel toggle switch is in the opposite position the color wheel will lock

in place. You can create a more dramatic effect by using split color combinations by stopping the

wheel anywhere between two adjacent colors.

©Eliminator® Los Angeles, CA. - www.EliminatorLighting.com

1 Year Limited Warranty: Eliminator Lighting warranty is valid from the date of purchase. Our

1 year limited warranty covers manufacturing defects only. Serial number, place of purchase with

dated valid receipt must be submitted at time of service. Eliminator Lighting warranty does not cover

items or parts prone to wear and tear: lamps, fuses, brushes and belts. Eliminator Lighting warranty

is only valid with-in the United States.

Caution! Never open unit when in use.

Always disconnect main power before

replacing the fuse. Remember to always

replace with the exact same type of fuse.

Fuse Replacement: Locate and remove the unit’s power cord. Once the cord has been removed

located the fuse holder located inside the power socket. Insert a flat-head screw driver into the power

socket and gently pry out the fuse holder. Remove the bad fuse and replace with a new one. The fuse

holder has a built-in socket for a spare fuse be sure not to confuse the spare fuse with active fuse.

Produkt Specifikationer

Mærke:	Eliminator Lighting
Kategori:	Ikke kategoriseret
Model:	Aqua LED

Har du brug for hjælp?

Hvis du har brug for hjælp til Eliminator Lighting Aqua LED stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Eliminator Lighting Manualer

Eliminator Lighting Aqua LED Manual

14 August 2025

Eliminator Lighting Electro Panel 192 Manual

14 August 2025

Eliminator Lighting MAC8M Manual

14 August 2025

Eliminator Lighting Vortex 150 Manual

13 August 2025

Eliminator Lighting Electro MH25R Manual

13 August 2025

Eliminator Lighting Elektron Bar FX Manual

13 August 2025

Eliminator Lighting Electro 86 Manual

13 August 2025

Eliminator Lighting Trio Par LED Manual

13 August 2025

Eliminator Lighting Electro 56 LED Manual

13 August 2025

Eliminator Lighting Electro Splash Manual

13 August 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Adj Event Bar Q4 Manual

14 August 2025

Bartscher A114003 Manual

14 August 2025

Swann SRNHD-888MSDWB2 Manual

14 August 2025

Adj Flashback 4 Manual

14 August 2025

Panduit FO6CB Manual

14 August 2025

Renkforce RF-WAT-300 Manual

14 August 2025

American Audio ETR 1000R Manual

14 August 2025

Swann SWIFI-MPRST Manual

14 August 2025

American Audio SENSE8 Manual

14 August 2025

Adj Vortex 1200 Manual

14 August 2025