EXSYS EX-1346 Manual

EXSYS Ikke kategoriseret EX-1346

Læs gratis den danske manual til EXSYS EX-1346 (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 22 personer og har en gennemsnitlig bedømmelse på 3.9 stjerner ud af 11.5 anmeldelser. Har du et spørgsmål om EXSYS EX-1346, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

6 5

Die EX 1346 ist ein Modul zur Umsetzung von USB 2.0 auf eine RS 422/485 Schnittstelle mit - -

FIFO 16C550 Port für den Anschluss von High Speed seriellen RS 422/485 Peripherie Geräten -

(z.B. Modem, Plotter usw.). Die EX 1346 ist mit einem USB 2.0 A Stecker zum Anschluss an - -

den PC und einem RS 422/485 seriellen 9 Pin Stecker ausgestattet. Das USB Modul ist Hot -

Plug & Play fähig. Für die Einstellungen der I/O Adressen und Interrupts sind keine Jumper und

Einstellungen notwendig, da die Einstellungen automatisch vom System BIOS und bei der

Installation des Betriebssystems vorgenommen werden.

Kompatibilität: USB 1.1, 2.0 & 3.2

Betriebssysteme: Windows 9.x / ME / 2000 / XP / Vista / 7 / 8.x / 10 / 11 / Server 20xx /

Linux / MAC

Anschlüsse: 1x USB 2.0 A Stecker, 1x 9 Pin Stecker Seriell RS 422/485 - -

Lieferumfang: 1346, Adapter 9 Pin Buchse zu 5 Pin Terminal Block, EX-

2x Sechskantmuttern, Treiber CD, Anleitung

Zertifikate:

BESCHREIBUNG & TECHNISCHE DATEN

AUFBAU

Anleitun

Vers. 1.2 / 06.09.24

E 134

ANSCHLÜSSE, STATUS LED S & DIP SCHALTER‘-

USB 2.0 A Stecker -

zum Anschluss an PC

S1: 9 Pin Stecker Seriell RS 422/485-

2x Sechskantmuttern

DB 9M RS 422/485 Anschlussbelegung:-

CONNECTORS, STATUS LED S & DIP SWITCH‘-

DB9 (EX-1346) DB9 (Endgerät)

1 TXD 1 TCD- -

2 TXD+ 2 TXD+

3 RXD+ 3 RXD+

4 RXD- 4 RXD-

5 GND 5 GND

DIP Schalter-

HARDWARE INSTALLATION

Because there are large differences between PC s, we can give you only a general installation ’

guide for the EX-1346. Please refer your computers reference manual whenever in doubt.

1. - - Connect the EX 1346 USB to the USB A Port at the your PC.

2. -If you would like to screw the serial cable to the 9 Pin connector of the EX 1346, then

unscrew the screws (see Picture 1) and screw the supplied hexagon nuts into the holes on

the EX 1346 (see Picture 2). Now you can attach the serial cable to the EX- -1346.

USB 2.0 A Plug:-

USB 2.0 A Plug-

Pin Signal Pin Signal

1 VCC 3 DATA+

2 DATA 4 GND -

Status LED‘s:

RXD

TXD

DIP Switch Position Description-

ON (Factory Settings) 2 wire RS 485 Mode- -

OFF 4 wire RS 485 or RS 422 Mode - - -

ON Reserved for features in future

OFF (Factory Settings) Reserved for features in future

ON 120 Ohm TXD Termination Resistor is Enabled

OFF (Factory Settings) 120 Ohm TXD Termination Resistor is Disabled

ON 120 Ohm RXD Termination Resistor is Enabled

OFF (Factory Settings) 120 Ohm RXD Termination Resistor is Disabled

DIP Switch:-

DRIVER INSTALLATION

CLEANING

Windows

After the hardware installation Windows will recognize the device automatically and install the

drivers. If the driver shoul not be installed automatically, please insert the Driver CD into your

CD-Rom drive (e.g. Drive D:) and open the folder USB_to_IO/FTDI Please select the folder „ “.

with your operating system and install the driver (see Picture). Follow the hardware assistant

and finish the installation. Restart your PC in any case after installing the drivers.Important!

For cleaning please use only a dry fluff less cloth and remove the dirt with gently pressure. In

the area of the connectors please make sure that no fibres from the cloth remain in the connect-

ors. Attention! Never use a moist or wet cloth for cleaning!

CHECK INSTALLED DRIVER

Open the . Now you should see at >Device manager< „Ports (COM & LPT) USB“ and „-

Controller“ the following new entry:

If you see this or a similar information the device is installed correctly.

Picture 1 Picture 2

Remove the Screws Insert the Hexagon Nuts

3. Now set the DIP Switch to the desired settings (see figure DIP- -Switch on page 2).

4. When you are ready you can start your PC and continue with the point „Driver Installation“.

HARDWARE INSTALLATION

RS- -422 und RS 485 4 Draht Anschlussbelegung-

RS- -485 2 Draht Anschlussbelegung

DB9 (EX-1346) DB9 (Endgerät)

1 NC 1 NC

2 NC 2 NC

3 DATA- 3 DATA -

4 DATA+ 4 DATA+

5 GND 5 GND

Produkt Specifikationer

Mærke:	EXSYS
Kategori:	Ikke kategoriseret
Model:	EX-1346

Har du brug for hjælp?

Hvis du har brug for hjælp til EXSYS EX-1346 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret EXSYS Manualer

EXSYS EX-44344 Manual

23 September 2025

EXSYS EX-44343 Manual

23 September 2025

EXSYS EX-45032IS Manual

24 Juli 2025

EXSYS EX-42034 Manual

24 Juli 2025

EXSYS EX-1311VIS Manual

24 Juli 2025

EXSYS EX-47925 Manual

24 Juli 2025

EXSYS EX-47200 Manual

23 Juli 2025

EXSYS EX-1305 Manual

23 Juli 2025

EXSYS EX-40032 Manual

23 Juli 2025

EXSYS EX-1332HMV Manual

23 Juli 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Kenu Airframe Wireless AFW-KK-NA Manual

4 November 2025

Beverage-Air Horizon HF1HC-1HS Manual

4 November 2025

EKO K400FDGC Manual

4 November 2025

Intermatic OP5GY24 Manual

4 November 2025

Abus Secoris BUBE60020 Manual

4 November 2025

Hillvert HT-TEMPLE-1 Manual

4 November 2025

Yamazen KABF-120H Manual

4 November 2025

RADEMACHER RolloTron Standard 1300 Manual

4 November 2025

ANCEL MT700 Manual

4 November 2025

Schneider Homeline HOM250PSPD Manual

4 November 2025