Hager EE805A Manual

Hager Bevægelsesdetektor EE805A

Læs gratis den danske manual til Hager EE805A (2 sider) i kategorien Bevægelsesdetektor. Denne vejledning er vurderet som hjælpsom af 42 personer og har en gennemsnitlig bedømmelse på 3.5 stjerner ud af 21.5 anmeldelser. Har du et spørgsmål om Hager EE805A, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

1 09/2017 - 6LE002943AHager Controls S.A.S., 33 rue Saint-Nicolas, B.P. 10140, 67703 SAVERNE CEDEX, France - www.hager.com

6LE002943A

EE804A

Presence and motion detector

360°, surface-mounted

EE805A

Presence and motion detector

360°, flush-mounted

Design and layout of the device

(Figure 1/2)

(1) Connecting terminals

(2) Mounting device locking screw

(3) Release opening

(4) Fastening grids

(5) Detector lens

(6) Response brightness potentiometer

(7) Potentiometer delay time

(8) Cover for potentiometer

(9) Locking screw

(10) Fixing springs

(11) Strain relief with mounting device for cable

ties

(12) Cover for connection compartment

Function

Correct use

- automatic switching of electric loads depend-

ing on heat motion and ambient brightness

- EE804A: Surface-mounted installation or in-

stallation on mounting box according to DIN

49073

- EE805A: Cavity installation

Product characteristics

- Combination of presence and motion detector

with enhanced detection sensitivity in the cen-

tral presence-detection area

- Response brightness adjustable

- Delay time adjustable

Behaviour during operation

The motion detector detects heat motion caused

by people, animals, or objects.

- will be switched on for the delay time if move-

ments are detected in the detection area and

the set response brightness is undershot.

Each detected movement restarts the delay

time.

- will be switched off if no additional movements

are detected in the detection area and the set

delay time has elapsed or the set response

brightness is exceeded.

Information for electricians

Installation and electrical connection

DANGER!

Touching live parts can result in an

electric shock!

An electric shock can be lethal!

Disconnect the connecting cables

before working on the device and

cover all live parts in the area!

Selecting installation location

The motion detector must be installed horizontally

on the ceiling. It has an detection angle of 360°.

The diameter of the detection area depends on the

installation height. At an installation height of 2.5

m, the diameter at ground level is approx. 6 m. The

diameter of the inner detection area with enhanced

detection sensitivity is 4 m (gure 3).

At an installation height greater than 2.5 m, the

detection area increases. At the same time, the

detection sensitivity decreases.

Observe the motion orientation: a distinction is

made between "direct approach" and "trans-

verse motion". Motions transverse to the motion

detector can be detected better than motions

toward the motion detector (Fig. 4).

If used as a presence detector, the device must

be installed so that areas with less motion activ-

ity (desk, seating area) are within the detection

area (gure 3).

Avoid sources of interference in the detection

area. Sources of interference, e.g. heating

elements, ventilation systems, air conditioners

and lamps that are cooling down can cause

undesired switching (Fig. 5).

Select an installation location that is free of

vibration. Vibrations can cause undesired

switching.

Connecting and installing the surface-mounted

variant EE804A (gure 7)

Run the connection cable through the insertion

opening (13).

Install device socket under the cover using the

screw dowel set enclosed. Installation can be

done on a ush-mounted box if available

Connect device according to connection dia-

gram (gure 6).

Snap onto base

Screw in locking screw (9).

Congure settings.

Close cover (8).

Safety instructions

Electrical equipment may only be installed and

assembled by a qualied electrician in accord-

ance with the relevant installation standards,

regulations, directives and safety and accident

prevention directives of the country.

Failure to comply with these installation in-

structions may result in damage to the device,

re or other hazards.

Due to its detection behaviour the device is not

suitable for use in burglary detection or alarm

systems.

These instructions are an integral component of

the product and must be retained by the end user.

(1)

(8)

(9)

(2)

(3)

(5)

(4)

(6) (7)

(4)

(5)

(10)

(11)

(12)

(10)

(6) (7)

0 m 2 m2 m

1 m

2 m

2,5 m

3 m3 m

Produkt Specifikationer

Mærke:	Hager
Kategori:	Bevægelsesdetektor
Model:	EE805A

Har du brug for hjælp?

Hvis du har brug for hjælp til Hager EE805A stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Bevægelsesdetektor Hager Manualer

10 August 2025

10 August 2025

9 August 2025

9 August 2025

9 August 2025

9 August 2025

21 Juli 2025

30 December 2025

9 December 2024

9 December 2024

Bevægelsesdetektor Manualer

Nyeste Bevægelsesdetektor Manualer

Theben TheLeda P24 WH Manual

18 December 2025

ORNO OR-CR-285 Manual

16 December 2025

Heath Zenith 4170 Manual

11 December 2025

Heath Zenith 5846 Manual

10 December 2025

Heath Zenith 4305 Manual

10 December 2025

Heath Zenith 7163 Manual

9 December 2025

Heath Zenith 7161 Manual

9 December 2025

MDT SCN-P360R306.01 Manual

8 December 2025

MDT PSE-PMC06.01S Manual

7 December 2025

MDT SCN-KP360R306.01 Manual

6 December 2025