Hager EE870 Manual

Hager Bevægelsesdetektor EE870

Læs gratis den danske manual til Hager EE870 (4 sider) i kategorien Bevægelsesdetektor. Denne vejledning er vurderet som hjælpsom af 19 personer og har en gennemsnitlig bedømmelse på 4.8 stjerner ud af 10 anmeldelser. Har du et spørgsmål om Hager EE870, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/4

+ 90°/- 30°

+/-80°

Description

Detection zone

Installation

Setting

Shutters

Connection by PIN system

(4 plug-in pins)

α = 220/360°

The optimal height of installation is 2.5 m.

The detection field must remain free.

2,5 m

LED A LED B

Accessories for corner  xing

8 m 16 m Ø 6 m

16 m

4 m

Plate for wall  xing

Swivelling detection head

Vertical adjustment

Setting potentiometers

Fixed time

(length of time

of lighting)

Luminosity Sensitivity

(modification

of the range)

Caution!

This device is to be installed only by a professional

electrician  tter according to local applicable

installation standards.

Do not plug in or unplug this product when it is live.

DETECTOR 220/360°

EE870 White

EE871 Charcoal

ACCESSORY FOR

CORNER FIXING

EE855 White

EE856 Charcoal

6E7582.C1

6E7582.C

EE87.

izMotion detectors comfort 220/360°

For use in Australia and New Zealand

Operating precautions

In order to obtain optimal detection conditions, it is recommended that the following advice:

- the detection is sensitive to solar radiation and bad weather. Detection performance is optimal up to

35 °C and above 40 °C.

- It is preferable to maintain à distance of 1 m. between a light source and the detector.

When mounting on a box, make sure that you do not distort the wall plate through excessive tightening

of the screws.

Montage

Surface-mounting or ceiling-mounted :

- x the wall plate using the screws provided

- connect the wall plate terminal block (see cabling plans in annex)

- fully insert the detector on the wall plate

- tighten the screws to ensure the product is sealed.

For corner xing, the wall plate is to be xed between the accessory and the detector.

Cable entry (breakable partitions) are possible:

- by the back (box mounting) or by the bottom.

LN S'

60 mm

Ateha raceways

ref. ATA 12200

or ATA 63000

Wiring and connections (provide installation with xed wiring)

Action Settings Potentiometer

Use Auto settings

(factory) or set by

the remote control

to switch the light

automatically for a

given time.

Auto Settings

Put the Lux potentiometer on

“auto test”.

The settings are predefined:

Lux = o

(operating at night only)

time = 3 min,

sensitivity = max.

Remote control settings

(Manual Settings inhibited).

Automatically switch

on the light for a

defined time.

Installer settings

Control a timer, a bell

etc.

Impuls V

Auto settings are usable with

time = 1s. (cannot be changed)

Test and validate the

detection zone.

Test mode

Move the potentiometer to 2

“auto test”. On this position, the

remote control can be used.

Adjust the sensitivity. Allows setting the range

to avoid disturbance.

“Normal” operation (on/off)

The lighting is activated whenever the level of

luminosity dened by the potentiometer 2 is

judged to be insufcient and a movement is

detected.

After detection, the light stays on for the length

of time predened by the potentiometer 1.

The xed timing is reset after each detection.

Please note: when the potentiometer is on “auto

test”, the settings are predened.

Control by timer

An impulse is generated every 10 s whenever the

level of luminosity is judged to be insufcient and

a movement is detected when the potentiometer

1 is on .V

This pulse mode is not suitable for connections to

power devices (except at low power loads).

Using the remote control (option,

ref. EE806)

The detector receives instructions from the remote

control when the Lux potentiometer is on the “auto

test” position.

If the potentiometer is put on another value, the

local setting resumes.

The LED B of the detector lights up to confirm the

signal with the remote control.

It flashes quickly for 2 s when an instruction is

received and 5 s for a reset.

When an instruction is not authorised, the LED

lights up for 1 s.

The available settings are:

- fixed time

- level of luminosity

- sensitivity

- on / off

- holidays (simulation of presence)

- activation of the detection A.

Testing and validating

the detection zone

Put the potentiometer on Test mode and if 2

necessary, use the shutters to define the detection

zone.

The Test mode is available for 3 min. Every

movement detected switches on the light for 1s.

After 3 min without detection of movement, the

product returns to normal operation.

Limiting the detection zone

You can limit the detection zone by using the

shutters provided or by tilting the head.

Product presentation

and operating principles

This detector allows automatic control of a

light source for a dened length of time when a

movement is detected in the surveillance zone.

The LED A indicates a movement. It is inhibited by

default except in Test mode.

Settings and Test

The detectors have 2 modes of operation:

Fixed time and Control by timer.

Power supply

The detector switches the light on for 40 s.

After 40 s, it activates the Normal mode.

6E7582.C2

Produkt Specifikationer

Mærke:	Hager
Kategori:	Bevægelsesdetektor
Model:	EE870

Har du brug for hjælp?

Hvis du har brug for hjælp til Hager EE870 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Bevægelsesdetektor Hager Manualer

21 Juli 2025

30 December 2025

9 December 2024

9 December 2024

9 December 2024

9 December 2024

9 December 2024

9 December 2024

9 December 2024

9 December 2024

Bevægelsesdetektor Manualer

Nyeste Bevægelsesdetektor Manualer

Hikvision DS-TDSB00-EKH Manual

28 Juli 2025

Blaupunkt IR-S1 Manual

28 Juli 2025

Panasonic ST4 Manual

25 Juli 2025

Steinel L 331 S Manual

25 Juli 2025

Steinel MD-8 ECO COM1 Manual

25 Juli 2025

Steinel PD-24 ECO COM1 Manual

25 Juli 2025

Steinel IS 3360 COM1 Manual

25 Juli 2025

Steinel PD-8 ECO COM1 Manual

25 Juli 2025

Steinel IS 3180 COM1 Manual

25 Juli 2025

Vimar 19485.M Manual

24 Juli 2025