Hager TXA661B Manual

Hager Lysdæmper TXA661B

Læs gratis den danske manual til Hager TXA661B (3 sider) i kategorien Lysdæmper. Denne vejledning er vurderet som hjælpsom af 31 personer og har en gennemsnitlig bedømmelse på 4.7 stjerner ud af 16 anmeldelser. Har du et spørgsmål om Hager TXA661B, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/3

6LE000384C

TYA661..

Dimmer 1gang

TXA661..

Dimmer 1gang

6LE000384C1

Safety instructions

Electrical equipment may only be installed and

assembled by a qualied electrician in accord-

ance with the relevant installation standards,

guidelines, regulations, directives, safety and

accident prevention regulations of the country.

Failure to comply with these instructions may

result in damage to the device, re or other

hazards.

Hazard due to electric shock. Disconnect be-

fore working on the device or replacing illumi-

nants. Take into account all circuit breakers

that supply dangerous voltages to the device.

Hazard due to electric shock. The device is not

suited for safe disconnection of the mains sup-

ply. Even when the device is switched off, the

load is not galvanically separated from the

mains supply.

Hazard due to electric shock on the SELV or

PELV installation. Do not connect any loads for

low voltage SELV, PELV or FELV together.

Do not connect any LED or compact uores-

cent lamps that are not expressly suitable for

dimming. The device could get damaged.

Do not connect lights with integrated dimmer.

Do not connect capacitive load and inductive

loads together on the output.

The permissible maximum load per device

must not be exceeded.

These instructions are an integral component

of the product and must be retained by the end

user.

Design and layout of the device

(1)

(2)

(3) (4)

(5)

(6)

(7)

(8)

(9)

(10)

Figure 1: Device overview

(1) Slide switch auto/min/max/manu

(2) Illuminated button for dimming mode

(3) KNX bus connection terminal

(4) Connection of load

(5) Labelling eld with cover

(6) Illuminated programming button

(7) Operation button for manual operation with

status LED

(8) Control LED short-circuit and overload pro-

tection

(9) Control LED overheating protection

(10) Mains connection

Function

System information

This device is a product of KNX system and corre-

sponds to the KNX guidelines. Detailed specialised

knowledge obtained from KNX training courses

is required for comprehension. The planning,

installation and commissioning of the device is

carried out with the help of KNX-certied software.

Systemlink start-up:

The function of the device is software-depend-

ent. The software is to be taken from the product

database. You can nd the latest version of the

product database, technical descriptions as well as

conversion and additional support programmes on

our website.

Easylink start-up:

The function of the device is conguration-de-

pendent. The conguration can also be done using

devices developed specially for simple setting and

start-up.

This type of conguration is only possible with

devices of the easylink system. Easylink stands for

easy, visually supported start-up. Precongured

standard functions are assigned to the in/outputs

by means of a service module.

Functional description

The device has a load output. It works with auto-

matic load detection depending on the connected

load in the phase cut-on or phase cut-off and ena-

bles switching and dimming via the KNX bus of:

- Incandescent lamps and halogen lamps

- Low-voltage halogen lamps with conventional

or electronic transformer

- dimmable LED and energy-saving lamps

Additionally, the device has a learn function for

more efcient control of energy-saving lamps and

230 V LED lamps.

Correct use

- Dimming of electrical loads AC 230 V.

- Installation on DIN rail according to DIN EN

60715 in distribution box.

Product characteristics

- Status display of the output on the device

- Manual activation of the output on the device

possible, building site operation

- Automatic load detection

- Setting the minimum and maximum dimming

value

- Timer functions

- Scene function

- Forced position by higher-level controller

Short-circuit and overload protection

Short-circuit and overload are signalled via the

control LED (8). The load is throttled (see Trouble-

shooting).

Overheating protection

Overheating of the device is signalled by a perma-

nent light of the control LED (9). The connected

load is throttled (see Troubleshooting).

6LE000384C2

Operation

Manual operation

Bus or mains power supply is present.

zPush switch (1) to position .

Manual operation is switched on, the output can

be controlled using the operation button (7).

During manual operation, the controller is deac-

tivated via the KNX bus.

Systemlink start-up:

Depending on the programming, the manual

operation is either activated permanently or for

a time period congured via the application soft-

ware. If the manual operation is disabled via the

application software, no activation takes place.

Or:

zMove switch (1) to position .auto

The manual operation is switched off. Operation

takes place solely via the KNX bus. The output

adopts the brightness predened by the bus

controller.

Operating output in manual operation

Operation takes place by a short or long press on

the operation button (table 1).

If the integrated LED ashes when pressing the

operation button, no load is connected.

Status Performance when pressing

the button

Load is switched

off.

Status LED of

the button (7)

is off.

Short press on button:

Switch ON the connected load.

LED lights up.

Long press on button:

Dim up to maximum brightness.

Status LED of the button (7)

lights up.

Load is switched

on.

Status LED of

the button (7)

lights up.

Short press on button:

Switch OFF the connected load.

Status LED (7) of the button

goes out.

Long press on button:

Changes the current bright-

ness. Dimming takes place in

the opposite direction of the last

dimming operation until maxi-

mum or minimum brightness.

Table 1: Manual operation

Information for electricians

Installation and electrical connection

DANGER!

Touching live parts can result in an

electric shock!

An electric shock can be lethal!

Disconnect the connecting cables

before working on the device and

cover all live parts in the area!

CAUTION!

Impermissible heating if the load of

the device is too high!

The device and the connected cables

may get damaged in the connection

area!

Do not exceed the maximum current

carrying capacity!

Observe temperature range. Provide sufcient

cooling.

zMount device onto DIN rail in accordance with

DIN EN 60715.

Connect device

Fig 2: Installation/deinstallation with plug-in terminals

Charge

(11)

Fig 3: Device connection

(11) Load

zConnect bus cable via connecting terminal (3).

Connect load (11) on the lower terminal strip (4)

of the device.

Start-up

Systemlik: Loading the physical address and

application software

The switch for manual operation (1) is in position

auto.

zSwitch on bus voltage.

zPress programming button (5).

The button lights up.

If the button does not light up, no bus voltage is

present.

zLoad the physical address into the device.

Status LED of the button goes out.

zLoad application software.

zNote down the physical address on the labelling

eld (5).

Easylink:

Information on the system conguration can be

taken from the extensive description of the service

module easylink.

Start up the device.

Switch on mains supply.

Functional test

The functionality of the outputs is displayed via the

status LED of the operation button (7).

LED status Meaning of the signal

LED lights up

permanently

Load is activated

LED ashes No load connected

Setting minimum and maximum dimming value

on the device

The device is ready for operation.

zSetting brightness value

The brightness value can be set by manual

operation on the device or by the programmed

dimming button of an operating unit.

zSet switch (1) to max. in order to apply the set

brightness as maximum dimming value.

Or:

zSet switch (1) to min. in order to apply the set

brightness as minimum dimming value.

zKeep the operation button (7) pressed for more

than 3 s.

The status LED ashes twice. The set bright-

ness value is saved.

If the minimum or maximum dimming value are

outside the setting range, the status LED (7)

ashes permanently after the save operation.

Setting dimming mode on the device

In the factory setting, the device performs an

automatic load detection for ohmic, inductive and

capacitive loads and selects the suitable dimming

performance. If the load type is known, this can

be specied on the device without performing an

automatic load detection.

The device is ready for operation.

zKeep the dimming mode button (2) pressed

until the status LED of the operation button (7)

ashes.

zBriey press the dimming mode button (2)

repeatedly until the coloured lighting of the

button (2) displays the desired operating mode

(Table 2).

zKeep the dimming mode button (2) pressed

until the lighting of the button (2) ashes quickly.

While the button is ashing quickly, the selected

operating mode is set. After that, the operating

mode is displayed for approx. 3 s before the

button goes out.

If the setting is not conrmed by holding down

the button, the device will revert to its previous

dimming mode after 2 minutes.

If the operating mode selected is not suitable

for the connected load, the dimming channel

will reset to „factory setting“ automatically.

Produkt Specifikationer

Mærke:	Hager
Kategori:	Lysdæmper
Model:	TXA661B
Kode for international beskyttelse (IP):	IP20
Produktfarve:	Grå
Driftstemperatur (T-T):	-5 - 45 °C
Antal produkter inkluderet:	1 stk