Holosun Paralow HS403B Manual

Holosun Ikke kategoriseret Paralow HS403B

Læs gratis den danske manual til Holosun Paralow HS403B (3 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 64 personer og har en gennemsnitlig bedømmelse på 4.8 stjerner ud af 32.5 anmeldelser. Har du et spørgsmål om Holosun Paralow HS403B, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/3

Fig 2-1

Features

Important notices

Battery

Installation

Fig1 PARALOW HS403B Red Dot Sight

www.holosun.com

HS403B

PARALOW Thank you for purchasing the PARALOW HS403B Red Dot

sight,Please read the User's Manual carefully.

1. The HS403B projects its aiming dot in

a way that prevents visibility when viewed from the front

beyond several meters.

2. The user can gain

rapid target acquisition and situational awareness while aiming

with both eyes open.

3. Only a few micro-a mperes of current

are required for sight operation. Sight runs on one battery for

up to 30,000 hours.

Concealed aiming:

Full field of view for target acquisition:

Low power consumption:

4. The sensitive motion sensor will turn the

power on with any motion detecon when in sleep mode.

5. arallax 1MOA

Motion power on:

Parallax free optical system: P is .

≤±

6. The sight will be automatically entered into

sleep mode motion less for 8 hours.

7. There are 12 settings(10 Daylight+2NV)

for the reticle so as to match the ambient lighting conditions.

8. The sight will remember the last saved

brightness setting when powered on and off.

9 The top mounted buttons allow

Sleep time delay:

Brightness adjustment:

Memory function:

Two top mounted buttons:

for easy operation without obstructing th e user's vision.

10. IP67 Waterproof:

1. Ensure that the firearm is completely unloaded and safe

before device installation or installing/replacing the

baery.

2. Please keep the packaging should you need to make a

warranty claim.

1.The operating voltage for this device is DC3V using one high

quality CR2032 Lithium battery.

2.The baery life is rated up to 50,000 hours at a mid-brightness

seing.

3.Baery Replacement:

Please follow the steps below for battery replacement

1. The included mount is

compatible with Picatinny Rails.

2. First insert the appropriate Torx wrench(included) into the

crossbolt head, then rotate to loosen cross bolt then

aach the sight into a suitable position,

and finally tighten the clamp screw to 15 IN/LBS using

non-permanent thread locker. (Fig3)

Bri ghtness Decrease Bri ghtness Increase

Protective Cap

Objective Lens

Eyepiece Lens T10 Torx Crossbolt

Model

Fig 3

Clamp

screw headCross bolt

2) Baery installation(Fig2-2):

a) Insert the baery into the battery tray 2032 with

oriented with the POSITIVE SIDE DOWN.

b) Insert and press the tray into the battery compartment.

Fasten screw 1,2.

Caution:

The loss or damage of seal ring will cause water to leak into

the compartment and may damage electronic circuits and

the device.

when battery runs out or for other condions that require

the baery to be changed :

1) Removing the battery (Fig 2-1):

a)Loosen screws 1,2.

b)Insert coin or similar object in the battery tray slot, pry

out the battery tray, and remove the discharged baery

by liing it up. A tool is provided for this purpose.

Fig 2-2

Slot

Screw 1

Screw 2

Screw 1

Battery

cabin

Battery

Seal ring

Sight operation

The operation panel is on the top of sight.(see Fig4)

Zero setting

Maintenance and care

Limited warranty

Fig 4

Brightness Decrease

Brightness Increase

PARALOW HS403B

Red Dot sight

1.On top of sight is the elevation adjusting turret, windage

adjusting turret is on the right side (see Fig5). The sight has

been factory adjusted for approximate zero.

2.The built in screw driver tool on the protective cap can be

used for zeroing alignment (see Fig5).See label inside cap.

3.First open the protective lid (see Fig1), position slot type

screwdriver on the slotted screw, then rotate the screw to

right or left for adjustment. Each left or right click is for one

adjustment, equivalent to 0.5M0A value.

4.Adjust the Elevation turret counterclockwise to move the

point of impact UP. Adjust the Windage turret counter-

clockwise to move the point of impact to the RIGHT. Turning

either turret clockwise moves the point of impact in the

opposite direction.

5.Caution:

Don't try to over rotate a turret, if you feel the turret can

Holosun Technologies Inc.

www.holosun.com

Phone: 909-594-2888

Email: @holosun.com

V2 2

warranty

1.Operation

1)Switch on: Press and release either brightness button

(”+”or”-”) to turn on the sight.

2) Brightness adjustment: There are 12 brightness settings.

The default brightness is the 7th level. Press the “+”or”-”

button until the red dot has a sufficient intensity to contrast

against the target. One changes

brightness

3)Power o: Press the”+”and”-”buttons simultaneously

turn the power and motion sensor off.

The sight will remember the last saved brightness

setting when powered on and off.

momentary press

by one step.

Note:

2.Motion sensor

1)Motion sensor is always enabled when the sight is on or in

sleep mode.

2)The sight will instantaneously wake up and turn on with any

motion detection to last saved setting.

1) Please note that your red dot will automatically

3. Sleep ime elayT r D

by default

a enter into sleep mode fter 8 hours of no movement.

2)The sleep time delay c be adjusted from 0 to 12 hours.

3)Sleep time delay

a)Press the “+”button for 3 seconds to enter time adjustment

mode. The red dot will blink .The number of blinks represents

the current time delay. One blink represents one hour of time

delay 8 blinks 8 hours

b)Press the “+”or”-”button to set the time. Pressing”+” or”-”

one or more times will increase or decrease the time by one

hour for each press. The LED will blink once to confirm each

button press. If the sleep time delay is set to”0”

the feature is disabled

c) ress the “+”button for 3 seconds to confirm the new

setting and exit the time adjustment mode.

. For example, equals .

r blinks

. 5 rapid blinks confirms this setting.

not be rotated, this indicates you have reached the

adjustment limit, otherwise the device may be damaged.

If the required adjusting range is beyond the limits, consider

adding an extra spacer between the device and mounting rail

to allow for additional adjustment.

This device is a precision instrument that deserves

reasonably cautious care. The following tips are provided to

ensure long lasting use of the sight.

The optical system, including the objective lens and

eyepiece lens are multi-coated optical glass. When cleaning

the lenses, blow away the dust on surface , wet the lens

with lens cleaner or clean water, wiping the fingerprint or

other oi stain with lens tissue, soft coon or microfiber cloth.

No special maintenance is needed for the housing surface.

Avoid touching the glass surface with dry cloth or tissue paper.

Do not use organic solvents such as alcohol or acetone. Do not

try to dismantle the device as the internal parts are specially

cleaned and sealed and with an anti-fog treatment. Any such

attempt will void the warranty.

If repair is needed, you can call our customer service center,

visit our website, or send an email to us.

We provide a limited lifetime warranty from the date of

purchase on parts and workmanship to the original purchaser.

At our sole discretion, we will repair or replace product found

to be defective under normal use and service without charge,

excluding any delivery costs, which will be born by purchaser.

We will not be liable for incidental, consequential, or

special damages arising out of or in any connection with the

use or performance of this product. This warranty is void if

the product has been misused, modified, neglected, or

disassembled prior to its return.

Please refer to http://www.holosun.com for current and

complete warranty information and other conditions.

SUMMARY

Produkt Specifikationer

Mærke:	Holosun
Kategori:	Ikke kategoriseret
Model:	Paralow HS403B

Har du brug for hjælp?

Hvis du har brug for hjælp til Holosun Paralow HS403B stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Holosun Manualer

Holosun HE530G Manual

6 Juli 2025

Holosun P.ID Plus Manual

3 April 2025

Holosun HS407C X2 Manual

3 April 2025

Holosun P.ID Dual Manual

3 April 2025

Holosun P.ID HC Manual

2 April 2025

Holosun HS407K X2 Manual

2 April 2025

Holosun P.ID Manual

2 April 2025

Holosun Paralow HS403B Manual

20 November 2024

Holosun AEMS-CORE-120101 Manual

5 September 2024

Holosun HS507C X2 Manual

5 September 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

10 Oktober 2025

10 Oktober 2025

10 Oktober 2025

10 Oktober 2025

Oras Saga 3970 Manual

10 Oktober 2025

TOA AT-4030B-EB Manual

10 Oktober 2025

TOA VX-030DA Manual

10 Oktober 2025

TOA RS-481 Manual

10 Oktober 2025

TOA AT-4200B-EB Manual

10 Oktober 2025

Xerox DocuShare Manual

10 Oktober 2025