Little Giant WF5 Manual

Little Giant Pumpe WF5

Læs gratis den danske manual til Little Giant WF5 (8 sider) i kategorien Pumpe. Denne vejledning er vurderet som hjælpsom af 10 personer og har en gennemsnitlig bedømmelse på 5.0 stjerner ud af 5.5 anmeldelser. Har du et spørgsmål om Little Giant WF5, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/8
INTRODUCTION
EN
You are now the owner of the finest fish-safe pond waterfall
designed specifically for garden and koi ponds. Please follow
these instructions to ensure a successful installation. The pond
waterfall is an important element of your water garden pond.
Waterfall features:
• Biovort™ technology for even water distribution on filter pads
and solids separating
• Industrial corrugated wall design
• Stainless steel band clamp for easy liner attachment
• Back-flush port offers easy maintenance and removal of settling
solid bio-loads, and helps to drain water from the waterfall
• Artificial rock and waterfall ledge with built-in drip ledge
IMPORTANT
Before beginning, read all instructions to familiarize yourself
with the products and additional accessories that can be used.
This will help to ensure that your water garden pond has been
developed to meet your needs and ensure a proper installation.
LOCATING THE WATERFALL
The waterfall can be located adjacent to the pond edge
in a simple configuration. It can also be located many feet
away from the pond with a stream connecting it to the pond. It is
recommended that the waterfall, or waterfall stream entering the
pond, be located on the opposite side of the pond in relation to
the pond skimmer.
EXCAVATING FOR THE WATERFALL
Refer to Figures 1 and 2 for rough-sizing the hole for the water-
fall vaults. Do not excavate too deep, especially in flat, low-lying
yards. The waterfall is meant to be slightly elevated in relation to
the pond for the most enjoyable water feature presentation.
INSTALLING THE WATERFALL
1. Determine which side of the vault will be the inlet. This is labeled
"INLET" and will always be the right-hand port.
2. If using 2" diameter PVC (rigid or flex), use a 3" hole saw to cut
the inlet opening. If using 3" diameter PVC, use a 4" hole saw.
NOTE: Do not cut the inlet opening with anything other than a
hole saw.
NOTE: The WF5 comes with a 2" adapter, and the WF10 with a
2" and 3" adapter.
3. Install the pipe grommet as shown in Figures 3a, 3b, and 4.
For easier installation, apply the provided Magic Lube to the
inside of the pipe grommet and the outside of the pipe to be
installed.
4. If using a manual back-flush system, it is recommended to cut
the hole in the left-hand port at this time. Refer to the instruc-
tions from the appropriate back-flush kit being used. If using a
Little Giant kit, use a 3" hole saw to cut this opening. The port
is provided with 3" diameter template.
5. Place the empty waterfall vault in the hole or desired location,
and check for clearance around the sides for backfilling.
IMPORTANT: Be sure the bottom of the hole, or surface sup-
porting the bottom of the waterfall vault, is compacted soil.
When excavating the location for the waterfall vault, dig a
round hole and leave ample clearance around for back-filling
with soil. Be sure to leave access to the inlet and back-flush
ports. If a hole is not being excavated, then be sure to back-fill
around the base and heavily compact to support the structure
(see Figure 3a).
IMPORTANT: Set the rear portion of the waterfall approxi-
mately 1/2" higher than the front. This provides the best pre-
sentation of water flowing over the rock, while also minimizing
1
WF5, WF10
Waterfall
Cascade
Caída de agua
31.5”
30.0”
25.0”
26.0”
Figure 1
Figure 2
Model: WF5
Pump Range: 1000 - 5000 GPH
Pond Size: 1000 - 5000 gallons
Material: High density polyethylene
Contents: Waterfall vault, mesh net bag with drawstring and
biological media, 2 filter pads, Biovort
™
, Biovort
™
support plate, artificial rock, band clamp, screw,
washer, and wingnut
Model: WF10
Pump Range: 5000 - 10000 GPH
Pond Size: 5000 - 10000 gallons
Material: High density polyethylene
Contents: Waterfall vault, mesh net bag with drawstring and
biological media, 2 filter pads, Biovort
™
, Biovort
™
support plate, artificial rock, band clamp, screw,
washer, and wingnut
Franklin Electric Co., Inc.
P. O. Box 12010
Oklahoma City, OK 73157-2010
888.956.0000 • Fax: 405.947.8720
www.LittleGiantLandscapeProducts.com
CustomerService-WTS@fele.com
Liner
Toile
Forro
Figure 5
the small amount of water that migrates to the drip ledge
(see Figures 3a and 3b). Back-filling above the level shown
in Figure 3a is optional (see Figure 3b). If desired, additional
soil, rocks, or plants may be incorporated to hide the waterfall
vault.
ATTACHING LINER AND WEIR
By this time the skimmer should be back-filled and the liner can be
attached. Be sure there is an adequate amount of liner available
below the waterfall prior to installing the liner. It is recommended
to have some slack to ensure the liner is not pulled due to rocks
that are added later. There is no need for silicone for the liner
attachment.
1. Hold outstretched liner up against front of waterfall weir ledge.
2. Measure a minimum of 7" out from the weir opening on both sides
of the waterfall and make a mark on the liner (Figure 5).
3. Make a 5" long cut down from the edge of the liner at the
location of the two marks made in Step 2. (Figure 5).
4. Wrap the portion of the liner (in between the two cuts made in
Step 3) over the top of the band clamp.
5. With the liner wrapped around the band clamp, position the
clamp in place on the band clamp sealing ledge (see Figure 6).
Make sure the wrapped portion of the liner doesn’t slip while
being installed.
6. Install the bolt in one end of the band clamp clasp and feed it
through other end of the band clamp clasp. Apply washer and
wing nut. Tighten wing nut until liner is snug (check by pulling
on the liner below the water fall weir ledge).
7. Inspect liner attachment to make sure liner is properly wrapped
around band clamp. This can be checked by raising the liner
up and looking underneath (you should be able to see the
liner protruding down from between the band clamp and the
band clamp sealing ledge on the vault). Tighten wing nut
further, if required. Be careful not to deform the clasp ends of
the band clamp.
INSTALLING THE ARTIFICIAL ROCK
When installing the artificial rock, make sure the surface of the
waterfall weir ledge is clean and dry. Similarly, check the bottom
surface of the artificial rock and make sure it is clean and dry.
Apply a generous amount of a polyurethane foam sealant (which
can be purchased at your local hardware store) to the entire
surface of the waterfall weir ledge. Be sure that some of this foam
is sprayed in the corners as well (Figure 7) so that it is forced
up between the rock and the vertical wall of the weir (Figure 8).
Right port: inlet water supply
Port de droite : entrée
d’alimentation en eau
Puerto derecho: entrada del
suministro de agua
Pipe grommet location
Lieu de la pipe oeillet
Ubicación de la tubería de drenaje timpánico
Left port: back-flush
Port de gauche :
rétrobalayage
Puerto izquierdo:
contraflujo
IMPORTANT:
Back-fill under
vault
IMPORTANT :
Remblayer sous le
bassin
IMPORTANTE:
Relleno
debajo del
bastidor
Install with back
end raised up 1/4”
Installer avec la
partie
arrière surélevée 6
mm (1/4 po)
Instalar con el
extremo posterior
levantado 6 mm
(1/4 pulg)
Figure 3a
Optional back-fill:
soil, rocks
Remblayage facultatif :
terre, rochers
Relleno opcional:
tierra, rocas
Required back-fill
Remblayage exigé
Relleno requerido
Right port: inlet water supply
Port de droite : entrée
d’alimentation en eau
Puerto derecho: entrada del
suministro de agua
Left port: back-flush
Port de gauche :
rétrobalayage
Puerto izquierdo:
contraflujo
Pipe grommet location
Lieu de la pipe oeillet
Ubicación de la tubería de drenaje timpánico
Figure 3b
Inside wall
of vault
Paroi intérieure
de la voûte
Pared interna
de la bastidor
Pipe grommet
Oeillet de tuyau
Tubería anillo protector
Outside wall
of vault
Paroi extérieure
de la voûte
Pared externa
de la bastidor
Figure 4
Figure 6
2

Produkt Specifikationer

Mærke: Little Giant
Kategori: Pumpe
Model: WF5

Har du brug for hjælp?

Hvis du har brug for hjælp til Little Giant WF5 stil et spørgsmål nedenfor, og andre brugere vil svare dig


Pumpe Little Giant Manualer

Little Giant

Little Giant WF5 Manual

22 August 2025
Little Giant

Little Giant TP 553674 Manual

6 Juli 2025
Little Giant

Little Giant 5MSP-WG Manual

6 Juli 2025

Pumpe Manualer

Nyeste Pumpe Manualer

DAB

DAB Evoplus 80/180 M Manual

4 Oktober 2025
DAB

DAB Jet 132 M Manual

4 Oktober 2025
DAB

DAB Genix 130 Manual

3 Oktober 2025
DAB

DAB Jet 82 M Manual

3 Oktober 2025
DAB

DAB Jet 102 M Manual

3 Oktober 2025
Draper

Draper Expert 07039 Manual

1 Oktober 2025
Intex

Intex Quick-Fill 166640 Manual

1 Oktober 2025
Intex

Intex QuickFill 166637 Manual

1 Oktober 2025
Intex

Intex Quick Fill 168609 Manual

1 Oktober 2025
Neptun

Neptun NRP-E 40 Manual

29 September 2025