Lowell ACS-1510-RPC Manual

Lowell Ikke kategoriseret ACS-1510-RPC

Læs gratis den danske manual til Lowell ACS-1510-RPC (3 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 66 personer og har en gennemsnitlig bedømmelse på 4.3 stjerner ud af 33.5 anmeldelser. Har du et spørgsmål om Lowell ACS-1510-RPC, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/3

INTERNAL USE ONLY: PN 24216

Lowell strives to provide accurate information while reserving the right to change specications and/or improve manufacturing methods without prior notication.

Spec 1108

Model ACS-1510-RPC | Rev. 12.20.23 | pg. 1/3

POWER RATING: 120VAC 60Hz 15A

CHASSIS: 30” x 2” x 2” steel chassis with black powder epoxy finish

TERMINATION: Detachable six-ft. IEC cord with NEMA 5-15P plug

RECEPTACLES: Total of ten NEMA 5-15R receptacles (five duplex). One duplex is un-

switched (always on when supplied with power). Four duplexes are switched (controlled by

a remote switch or sequencer through the RPC terminal).

UNIVERSAL MOUNTING BRACKETS: The universal brackets allow for power strip instal-

lation in a variety of applications with receptacles facing front, center or rear. Brackets are

engineered with multiple mounting points and include two types of hardware to facilitate

easy installation in a rack with adjustable or fixed rails, to a wall, or under a desk/counter.

The brackets can be mounted so they are exposed for easy access or concealed beneath

the power strip for an aesthetically cleaner installation.

CERTIFICATION: ETL Listed in U.S./Canada

ORIGIN: Assembled in the U.S.A. with global components.

INSTALLATION

Use the universal mounting brackets to install the power strip near the equipment. Use

low-voltage cable to connect the RPC terminal to a remote switch or sequencer (required).

The corded power strip with ten 15A receptacles (ve duplex) and remote power control

function (RPC) can be combined with a variety of remote switches or sequencers to provide

a low-voltage method of turning specic equipment on and off from a remote location. The

ability to safely control AC power distribution without directly accessing equipment adds con-

venience, while minimizing the potential for unauthorized system modications.

ACS Series Model No.

ACS-1510-RPC

AC Power Strip w/Remote Power Control

FEATURES

Certied

US Steel

Assembled

In USA

with Global

Components

A&E SPECIFICATIONS

The ETL Listed power strip with low-voltage remote power control shall be Lowell model

ACS-1510-RPC, which shall have a power rating of 120VAC 60Hz 15A with circuit breaker

protection. The chassis shall be steel with black powder epoxy finish, measuring 30” x 2”

x 2”. It shall feature one unswitched and four switched NEMA 5-15R duplex receptacles.

The four switched duplexes shall be controlled by an external power switch or sequencer

(ordered separately) that is connected to the power strip’s remote power control terminal.

The power strip shall be made in the U.S.A. with global components. It shall terminate with

a detachable 6 ft. IEC cord with NEMA 5-15P plug, and include universal mounting brackets

with hardware to mount to a rack, wall or desk.

RPC terminal

connects to a

remote switch

or sequencer.

Four

duplexes are

controlled by a

remote switch

or sequencer

connected to

the RPC terminal.

One duplex

is unswitched

(always on).

Detachable

power cord

Mounting brackets

Note: An external

power switch or se-

quencer is required

(order separately,

pg. 2).

INTERNAL USE ONLY: PN 24216

Lowell strives to provide accurate information while reserving the right to change specications and/or improve manufacturing methods without prior notication.

Spec 1108

Model ACS-1510-RPC | Rev. 12.20.23 | pg. 2/3

On: Green LED indicates AC power is applied to receptacles.

Power: Red LED indicates AC power is available.

Test: Test applies power to receptacles independent of remote switch or sequencer.

SW, Com: Connection between Switch and Common terminals activates internal relay and applies power to receptacles.

V+ Out: +24VDC output. Use only with RPS Series switches

Ex. Lowell RPS Series