Lowell ACS-2006-3C-RPCP-HW Manual

Lowell Ikke kategoriseret ACS-2006-3C-RPCP-HW

Læs gratis den danske manual til Lowell ACS-2006-3C-RPCP-HW (3 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 33 personer og har en gennemsnitlig bedømmelse på 4.3 stjerner ud af 17 anmeldelser. Har du et spørgsmål om Lowell ACS-2006-3C-RPCP-HW, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/3

Lowell strives to provide accurate information while reserving the right to change specications and/or improve manufacturing methods without prior notication.

Spec 2319

Model ACS-2006-3C-RPCP-HW Rev. 12-08-21 | pg. 1/3

INTERNAL USE ONLY: PN 24552

This hardwired power strip features three circuits featuring a total of (3) 20A duplex outlets.

One circuit with a duplex outlet is unswitched (always on). The other two circuits (one duplex

each) are activated by a compatible sequencer (model SEQ-P4 or SEQR-P4) which is required

for activation (order separately).

FEATURES:

• Outlets: Total of three (3) NEMA 5-20R duplex outlets

• Power Rating: 120VAC 60Hz 20A each circuit

• Unswitched Circuits: One unswitched circuit is always on (1 duplex).

• Switched Circuits: Two switched circuits (1 duplex each) are controlled by an external

sequencer. Each circuit has its own DIP switch to set its position in the sequencing order (1,

2, 3, or 4). Set one (and only one) step for each circuit.

Note: Two or more circuits can be assigned to the same sequencing step. However, each

circuit must only be assigned a single step (because it can only activate once). If any circuit is

not assigned a step, that circuit will not activate. If any circuit is assigned more than one step,

the entire system will malfunction.

• Pass-through RJ45 Jacks:

– The switched circuits are internally connected to the RJ45 jacks and will therefore be

controlled by the external sequencer when it's connected to either jack (using Cat5/6 cable,

not included).

– The RJ45 jacks can be used to daisy chain compatible remote power controls or relays (up

to 20 devices per step). See RPC-P or RY-P Series on last page.

• Surge Protection: Each of the two switched circuits includes surge protection — the

unswitched circuit is not protected.

– Maximum Surge Current: 10,000A

– VPR: 400V

– Response Time: 1 nanosecond

– EMI/RFI Noise Reduction: 20dB@100kHz

– Protection Mode: Line to Neutral

– Ground Contamination: None

• Chassis: 30" x 2" x 2" steel chassis with black powder epoxy finish.

• Non-metallic Flexible Conduit: Terminates to six ft. flexible conduit with pigtail leads tagged

for circuit identification. Conduit can be trimmed in the field as needed.

• Mounting Brackets: Universal mounting brackets provide versatility allowing the outlets to

face forward, center or rear of rack. Minimal rack panel space required = 33.25" (19U).

• Origin: Made in the U.S.A. with global components.

• Third Party Listing: ETL Listed (to UL 60065)

• A&E Specifications: The hardwired power strip shall be Lowell model ACS-2006-3C-RPCP-HW

with power rating of 120VAC 60Hz 20A. The 30" x 2" x 2" steel chassis with black powder epoxy

finish shall include three circuits and three NEMA 5-20R duplex outlets. One duplex outlet shall

be on an unswitched circuit (always on). The other duplex outlets shall be on two switched circuits

which shall be activated and deactivated by Lowell power sequencer model SEQ-P4 or SEQR-P4

(ordered separately). The power strip shall feature surge protection up to 10,000A on the two

switched circuits; the unswitched circuit shall not have protection. The unit shall include universal

mounting brackets and a six ft. non-metallic flexible conduit with pigtail leads. The power strip shall

be made in the USA with global components. It shall be ETL Listed.

3-circuit power strip with pass-thru jacks: ACS-2006-3C-RPCP-HW

Unswitched

Circuit:

(always on)

Rotating connector

for 6 ft. exible

conduit

Pass-through

RJ45 jacks –

in from a sequencer

(out to compatible

devices, if desired)

Switched

Circuit 1:

Switched

Circuit 2:

LED status

indicator and

sequence step

switch

LED status

indicator and

sequence step

switch

Mounting brackets

Made in USA

Produkt Specifikationer

Mærke:	Lowell
Kategori:	Ikke kategoriseret
Model:	ACS-2006-3C-RPCP-HW

Har du brug for hjælp?

Hvis du har brug for hjælp til Lowell ACS-2006-3C-RPCP-HW stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Lowell Manualer

Lowell PCMB-6 Manual

1 September 2025

Lowell RPC-20-CD Manual

28 August 2025

Lowell ACS-1530-IEC Manual

3 April 2025

Lowell ACS-2020-IG-6C-HW Manual

11 December 2024

Lowell ACR-SEQ4-1509 Manual

11 December 2024

Lowell ACS-2006-3C-RPCP-HW Manual

10 December 2024

Lowell ACS-2014-HW Manual

7 December 2024

Lowell ACS-1510-RPC Manual

7 December 2024

Lowell RPC-30 Manual

7 December 2024

Lowell ACS-2012 Manual

7 December 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

PAG Mini link 6002 Manual

4 November 2025

Wamsler K128 Manual

4 November 2025

Sonifex Redbox RB-DSD8 Manual

4 November 2025

Zotac ZBOX MI561 nano Manual

4 November 2025

MuxLab 500800-RX Manual

4 November 2025

Hawke Laser/LED Foregrip Manual

4 November 2025

Wooden Camera 213900 Manual

4 November 2025

Chauvet Freedom Flex Stick Battery Manual

4 November 2025

DS18 VOC8LD-PK Manual

4 November 2025

Sony XDCAM PXW-Z90 Manual

4 November 2025