Master Lock T8-331ML Manual

Master Lock Pengeskab T8-331ML

Læs gratis den danske manual til Master Lock T8-331ML (25 sider) i kategorien Pengeskab. Denne vejledning er vurderet som hjælpsom af 26 personer og har en gennemsnitlig bedømmelse på 4.8 stjerner ud af 13.5 anmeldelser. Har du et spørgsmål om Master Lock T8-331ML, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/25

Security Safe Owner’s Manual

T6-331ML, T8-331ML, T0-331ML

: Masterlock.eu/Safes

INSTRUCTIONS FOR USE ......................................................... 2

MODE D’EMPLOI .....................................................................3

GEBRAUCHSANWEISUNG .........................................................4

GEBRUIKSAANWIJZING ...........................................................5

INSTRUCCIONES DE USO ..........................................................6

ISTRUZIONI PER L’USO ............................................................7

INSTRUÇÕES DE UTILIZAÇÃO ....................................................8

ΟΔΗΓΙΕΣ ΧΡΗΣΗΣ ...................................................................9

BRUKSANVISNING ..................................................................10

BRUGSANVISNING .................................................................11

KÄYTTÖOHJE ..........................................................................12

BRUKSANVISNING ..................................................................13

INSTRUKCJA UŻYCIA ...............................................................14

HASZNÁLATI ÚTMUTATÓ ..........................................................15

MOD DE UTILIZARE ................................................................. 16

NÁVOD K POUŽITÍ ...................................................................17

ИНСТРУКЦИЯ ПО ПPИMEHEHИЮ.............................................18

KULLANIM TALİMATI ...............................................................19

ENGLISH

To ADD a User code (Option 2):

1 Press and release red setup

button on the inside of

the door near the hinge.

The green light on the

keypad will ﬂash and

beep twice.

2 While the green light is on. Enter a 5 digit user code of

your choice. The light will turn off.

Programming the Secondary Code

To ADD a Secondary code:

1 Press the “Prog” key two times.

2 Enter the 5 digit user code previously programmed.

The green light will remain on.

3 Enter the 5 digit secondary code of your choice.

The light will turn off.

NOTE: To enter a new secondary code, repeat the above steps.

To DELETE a Secondary code:

1 Press the “Prog” key two times.

2 Enter the 5 digit user code.

3 Enter 0,0,0,0,0.

Bolt Down Instructions

1 Set a suitable and convenient location for your safe.

2 Set the safe in place and use the holes provided in the bottom or

back of the safe to mark the location of the holes to be drilled in

the ﬂoor or wall.

NOTE: It is not recommended to attempt to bolt to both ﬂoor and wall.

If bolting to a wall, please ensure that the safe is resting on a

supported surface, i.e. ﬂoor, table, or shelf.

3 Move the safe away and drill holes of the appropriate diameter

and depth for the type of hardware being used and the

mounting surface.

4 Place the safe back over the holes and install the fasteners

as required.

Security Safe

Thank you for choosing Master Lock to store all your important documents and valuables.

We hope that this product will help you stay organized and provide you with the peace-of-mind of knowing the things most important to you are protected.

Warning

Your safe is only part of your total security protection.

Master Lock recommends that you store your safe in a closet, ofﬁce,

basement, bedroom or any other location that is convenient for you but

out of direct line of sight from prying eyes. The location of the safe does

not affect the safe’s ability to protect your valuables inside.

Preparing Your Safe for the

First Time

Installing Your Batteries

NOTE: Do not use rechargeable batteries or any other type of

non-alkaline battery. Do not mix old and new batteries.

Do not mix alkaline with standard batteries.

1 Remove the keypad by rotating

the cover counter-clockwise and

pulling towards you.

2 Insert your override key

(skeleton key) in the hole

and rotate clockwise.

3 Open the door using the lever

handle of the safe.

4 Locate the key hook plate

located on the inside back of

the door. Remove the plate by

sliding the cover upwards and

then pull towards you.

5 Insert four (4) alkaline AA

batteries as indicated.

6 Replace the key hook plate on

the back of the door.

NOTE: This override key can be used to access the safe in case of a

forgotten combination or low battery power. DO NOT store the

override key inside the safe.

Using Your Safe

M100TEST

SN100TEST01*

12345

Enter the ﬁve digit factory code

(located on last page of this

owner’s manual) .

2 Push lever down and pull

open door.

NOTE: The lock automatically enters a two-minute delay mode after

an invalid code has been entered three consecutive times.

Programming Safe Features

Your Digital Lock

Factory code:

The safe will ALWAYS unlock using this 5 digit code (found on the back

of the owner’s manual). This code cannot be deleted.

User code:

A 5 digit programmable code of your choosing that can be changed.

Secondary code:

A second 5 digit programmable code of your choosing that can be

changed or deleted. Can only be programmed after a user code has

been activated.

Programming a User Code

NOTE: Always test your combination several times with the door open

before placing valuables inside the safe.

To ADD a User code (Option 1):

1 Press the “Prog” key.

2 Enter the 5 digit factory code found on the back of your

owner’s manual. The green light will remain on.

3 Enter a 5 digit user code of your choice. The light will turn off.

NOTE: To change the user code, repeat the above steps.

Troubleshooting

THE PROBLEM: WHY IT IS HAPPENING: THE SOLUTION:

Red LED light + three (3) beeps 1. You pressed program key out of sequence

2. You have entered an invalid code

3. You have let ﬁve (5) seconds or more elapse

between key entries

Try entering your factory, user or secondary code again.

Yellow LED light Indicates a low battery Replace the four (4) AA alkaline batteries in your safe.

NOTE: When the new batteries are installed, the yellow

LED may come ON and stay ON during the ﬁrst

lock operation before it turns off.

Safe won’t open An invalid code has been entered three

consecutive times which has activated the time

delay mode

Wait for 2-minutes and then try entering your factory,

user or secondary code again.

Got a question?

If you ever have any questions regarding your Master Lock product, please visit our website masterlock.eu/safes.

Produkt Specifikationer

Mærke:	Master Lock
Kategori:	Pengeskab
Model:	T8-331ML
Type:	Fritstående pengeskab
Bredde:	550 mm
Dybde:	502 mm
Højde:	700 mm
Vægt:	88500 g
Produktfarve:	Sort
Antal:	1
Materiale:	Stål
Indvendige mål (B x D x H):	520 x 352 x 655 mm
Strømkilde type:	Batteri
Batteritype:	AA
Antal understøttede batterier:	4
Kapacitet:	119.9 L
Antal hylder:	3 hylder
Låsetype:	Code, Electronic, Key
Låsning:	Ja
Justerbare hylder:	Ja
Bedste anvendelsesmuligheder:	Document, Jewelry, Small electronics
Antal bolte:	3
Antal nøgler inkluderet:	2 stk