Mikrotik CSS326-24G-2S+RM Manual

Mikrotik Ikke kategoriseret CSS326-24G-2S+RM

Læs gratis den danske manual til Mikrotik CSS326-24G-2S+RM (4 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 48 personer og har en gennemsnitlig bedømmelse på 4.5 stjerner ud af 24.5 anmeldelser. Har du et spørgsmål om Mikrotik CSS326-24G-2S+RM, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/4

CloudSmartSwitch 326

The CSS is a switch with 24 Gigabit Ethernet ports and two SFP+ ports. All ports are connected through a switch chip.

The device runs SwOS operating system, specifically made for Switches.

First use

Connect your devices to the desired ports in any order.

Management IP address of the device is 192.168.88.1.

to access it, your PC needs to be within the same IP network.

The management interface is available from the web browser.

but the device can be discovered using Winbox utility as well.

Username is admin, there is no password.

Powering

The device accepts power from the power jack or from the first Ethernet port (Passive PoE).

Direct-input power jack (5.5mm outside and 2mm inside, female, pin positive plug) accepts 11-30V DC.

The first Ethernet port accepts passive PoE input 11-30V DC.

Power consumption 19 W.

Operating system support

This device runs SwOS, which is the only supported OS for this device. Information about SwOS:

http://wiki.mikrotik.com/wiki/SwOS

Extension slots and ports

24 individual Gigabit Ethernet ports, supporting automatic cross/straight cable connection (Auto MDI/X), so

you can use either straight or cross-over cables for connecting to other network devices.

2 SFP+ ports for using 10G SFP+, 1.25G Optical fiber or copper Ethernet modules

Reset button

Hold this button during boot time until LED light starts to flash. Release the button to reset SwOS configuration and

load backup software for reinstallation and upgrade.

See mikrotik.com/products for the latest version of this document. Document #49066 Modified on: 26.APR.2019

Federal Communication Commission Interference Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of

the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a

residential installation.

This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance

with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that

interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to

correct the interference by one of the following measures:

•Reorient or relocate the receiving antenna.

•Increase the separation between the equipment and receiver.

•Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

•Consult the dealer or an experienced radio/TV technician for help.

FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could

void the user’s authority to operate this equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This

device may not cause harmful interference, and (2) this device must accept any interference received, including

interference that may cause undesired operation.

Note: This unit was tested with shielded cables on the peripheral devices. Shielded cables must be used with the unit

to ensure compliance.

Industry Canada

This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two

conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including

interference that may cause undesired operation of the device.

Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence.

L'exploitation est autorisée aux deux conditions suivantes: (1) l'appareil ne doit pas produire de brouillage, et (2)

l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en

compromettre le fonctionnement.

See mikrotik.com/products for the latest version of this document. Document #49066 Modified on: 26.APR.2019

Produkt Specifikationer

Mærke:	Mikrotik
Kategori:	Ikke kategoriseret
Model:	CSS326-24G-2S+RM
Bredde:	440 mm
Dybde:	144 mm
Højde:	44 mm
Brugervejledning:	Ja
Produktfarve:	Hvid
Formfaktor:	1U
Strømforbrug (typisk):	19 W
Driftstemperatur (T-T):	-40 - 70 °C
Sikkerhedsalgoritmer:	SNMP
Intern hukommelse:	2 MB
Netværksstandarder:	IEEE 802.1Q
Webbaseret administration:	Ja
Knap til nulstilling:	Ja
AC-adapter inkluderet:	Ja
Harmoniseret systemkode (HS):	85176990
Flashhukommelse:	2 MB
Strøm over Ethernet (PoE):	Ja
Indbygget processer:	Ja
Monteringsbeslag inkluderet:	Ja
Switch-type:	Administreret
10G understøttelse:	Ja
Spanning tree protokol:	Ja
VLAN understøttelse:	Ja
Port-spejlning:	Ja
Antal VLAN'er:	4000
Broadcast stormkontrol:	Ja
Basis omskiftning RJ-45 Ethernet porte, antal:	24
Basis omskiftning RJ-45 Ethernet porttype:	Gigabit Ethernet (10/100/1000)
Adgangskontrolliste (ACL):	Ja
Filtrering af MAC-adresser:	Ja
MAC adresselabel:	- entries
Switch kapacitet:	- Gbit/sek.
Stativ-montering:	Ja
Strømstik:	DC-in-stik
Strømforsyning inkluderet:	Ja
Antal SFP + modulslots:	2
Antal strømforsyninger:	1