PAC AAI-GM9 Manual

PAC Ikke kategoriseret AAI-GM9

Læs gratis den danske manual til PAC AAI-GM9 (1 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 23 personer og har en gennemsnitlig bedømmelse på 4.9 stjerner ud af 12 anmeldelser. Har du et spørgsmål om PAC AAI-GM9, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/1

Pacic Accessory Corporation - 1502 S. Santa Fe Street, Santa Ana, CA 92705

techsupport@pac-audio.com • Voice: 714-835-3022 • Fax: 714-835-3233 • www.pac-audio.com

11-16-05

AAI-GM9

Auxiliary Audio Input for GM Vehicles

The AAI-GM9 allows direct interface of any preamp level audio source to a GM factory radio

with a slave unit, eliminating the need for sound degrading solutions like an FM modulator.

The AAI-GM9 interface inputs sources from units such as a DVD, VCP, MP3, Satellite Radio

or PlayStation.

• Lower cost and higher quality sound than a FM modulator.

• Perfect for SUV’s like Escalade, Tahoe, Suburban, Denali and Yukon.

• Comes with a three position switch which allows you to switch between two auxiliary inputs and the

factory slave unit.

• High quality audio isolation IC eliminates engine noise.

• Internal CMOS electronic switching for long term reliability.

• Completely plug & play. Requires no external wiring.

• Seamless operation with OnStar® equipped vehicles.

Requirements: For 1995-2002 vehicles* the Sedan or SUV factory headunit must have a

working slave unit which uses the GM 9 pin connector. Slave unit examples are: factory/

aftermarket CD changer, separate factory cassette player or single CD player.

Installation

1. Remove factory 9 pin connector from radio and insert the AAI-GM9 male plug in it’s place.

Plug factory 9 pin connector into the AAI-GM9 female connector as shown in Fig.1 below.

2. Plug RCA cables from rst audio source into Aux1 input of AAI-GM9. If there is a second

audio source, plug RCA into Aux2 input.

3. Mount the toggle switch in a suitable location.

AAI-GM9

GM Auxiliary Audio Input

Aux 1

Input

Aux 2

Input

Pacific Accessory Corporation, Santa Ana, CA 91792

Left

Right

Aux1/Aux2

Switch

Insert these two plugs in between the

factory headunit and factory 9 pin plug

DELCO ELECTRO NICS

123

4 5 6

SEEK

TAPEAUX

AM FM

FADE BAL BASS TREB

EJECT

PWR VOL

TUNE

RECALL

Factory wire harness

to factory slave unit

DVD player

or Satellite Radio VCP player

or Playstation

Fig. 1

Brown wire

Testing

1. Turn radio on and select Tape or CD changer source. Note: a cassette or CD must be

inserted into the slave unit and playing.

2. With the switch in the middle position you should hear the Tape or CD audio.

3. When you ip the switch left or right of the middle position, you should hear Aux1 or Aux2

audio.

4. Vehicles with OnStar®: When activating OnStar® with the AAI-GM9 switch to either

Aux1 or Aux2, the auxiliary audio will be automatically overridden so OnStar® audio can

be heard. When turning off OnStar®, Aux1 or Aux2 audio will resume.

5. Connect the brown wire to chassis ground only if the portable player Portable Players:

and other audio source is not using the vehicle’s battery as a power supply.

OnStar® Ready!

Most overhead video consoles have a +12 volt

trigger output when the video system is turned

on. Use a SPDT relay as shown and connect

pin 30 of relay to the AAI-GM9 switch’s red wire.

Connect pin 87 to the AAI-GM9 switch’s shield

wire. Use Aux2 as the external audio source

input and leave switch in the middle position.

This automatic feature will only work on Aux2

input and not Aux1.

87a

To overhead

+12v trigger output

Tap into AAI-GM9

switch's red wire

Tap into AAI-GM9

switch's shield(bare) wire

Terminal side of switch

Red

White

Shield

Using external video source to automatically trigger the AAI-GM9 for Aux2

Description

Bulletin

1999-2000 Escalade, Denali and 1999-2002 Pontiac Grand Prix

1999-2000 Cadillac Escalade, GMC Denali and 1999-2002 Pontiac Grand Prix, see bulletin.

To retain the automatic switching when OnStar® is activated, relocating the Lt..

green wire from the AAI-GM9 to the factory

21 pin radio connector will be necessary.

1. Cut the Lt.. green wire coming from the

AAI-GM9 at white plug leaving the wire in be-

tween the two connectors intact. Tap the wire

into pin #15 dark green wire of the factory 21

pin connector shown to the right.

11 20

1 10

Factory Plug Shown from

pin side not wire side

Produkt Specifikationer

Mærke:	PAC
Kategori:	Ikke kategoriseret
Model:	AAI-GM9

Har du brug for hjælp?

Hvis du har brug for hjælp til PAC AAI-GM9 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret PAC Manualer

PAC CAM-GM51 Manual

11 Juli 2025

PAC TY1A-RS Manual

11 Juli 2025

PAC SR-F15009HX Manual

10 Juli 2025

PAC SRK-RAM13HX Manual

10 Juli 2025

PAC AAI-TY3 Manual

30 Juni 2025

PAC SRK-GM14HX Manual

10 Marts 2025

19 Februar 2025

19 Februar 2025

19 Februar 2025

19 Februar 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Waterstone 7800 Manual

11 December 2025

Kwikset 258 Manual

11 December 2025

Schlage F170 Manual

11 December 2025

Moen Align 7565EV Manual

11 December 2025

Energy Sistem ESG M3 Neon Manual

11 December 2025

ALNO MC10244 Manual

11 December 2025

JET TAK-ZX Manual

11 December 2025

Crosley Nashville CF1165 Manual

11 December 2025

Waterstone 1455 Manual

11 December 2025

Laica NE2015 Manual

11 December 2025