PAC AOEM-FRD24 Manual

PAC Ikke kategoriseret AOEM-FRD24

Læs gratis den danske manual til PAC AOEM-FRD24 (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 21 personer og har en gennemsnitlig bedømmelse på 4.4 stjerner ud af 11 anmeldelser. Har du et spørgsmål om PAC AOEM-FRD24, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

Pacific Accessory Corporation – 835 835 3233 1502 S. Santa Fe Street, Santa Ana, CA 92705Voice: 714- - -3133 Fax: 714 -

OEM-1 REV. 12- -1 00

Cables for replacing Factory head unit.

Installation instructions for cables on list “A”

This “A” cable, is used when replacing a factory radio. (the appropriate cable from list “B” is also required). One end of

cable plugs into or connects to your new aftermarket head unit and the other end plugs into the 18 pin connector of the OEM-

1. When using the complete OEM-1 system the radio will be current protected by the vehicle fuse. The installer must

decide to transfer any other fuses or noise filters from the harness provided with the head unit. Use the wire / terminal

identification chart below to locate the correct power wires.

While every effort has been made to insure this cable was made to connect properly to your aftermarket head unit,

changes in models and configurations do occur. To prevent potential damage consult your stereo’s owners manual

and check wire function (as shown below) with that of the head unit you have. Move any wires that are not in the

correct pin location for you head unit.

Installation instructions for cables on list “B”

This “B” cable, is used when replacing a factory radio. (the appropriate cable from list “A” is also required). One end of

this cable plugs into the vehicle dash harness that was removed from the factory radio. (the AMP-UNV harness must be

spiced into the vehicle harness, use the 16 pin chart below for wire identification) The other end plugs into the 16 pin

connector of the OEM-1.

WIRE AND TERMINAL IDENTIFICATION

Output of the OEM-1, 16 pin connector (cable “B” or AMP-RCA). Looking into connector / wire side of cable.

WIRE COLOR WIRE COLOR CIRCUIT CIRCUIT

ORANGE ILLUMINATION 8 16 IGNITION SWITCH 12V RED

BLUE/WHITE AMP TRIGGER 7 15 BATTERY YELLOW

BLACK GROUND 6 14 POWER ANTENNA BLUE

PURPLE/ BLK RIGHT REAR (-) 5 13 RIGHT REAR (+) PURPLE

GREEN/ BLACK LEFT REAR (-) 4 12 LEFT REAR (+) GREEN

N/C 3 11 N/C

GRAY/ BLACK RIGHT FRONT ( -) 2 10 RIGHT FRONT (+) GRAY

WHITE/ BLACK LEFT FRONT ( -) 1 9 LEFT FRONT (+) WHITE

Input of the OEM-1, 18 pin connector (cable “A” or “C”). Looking into connector / wire side of cable.

WIRE COLOR WIRE COLOR CIRCUIT CIRCUIT

WHITE/ BLK LEFT FRONT ( -) 9 18 LEFT FRONT LOW LEVEL (+) WHITE/ RED

GRAY/ BLK RIGHT FRONT ( -) 8 17 LEFT FRONT HIGH LEVEL (+) WHITE

GREEN/ BLK LEFT REAR (-) 7 16 RIGHT FRONT LOW LEVEL (+) GRAY/ RED

PURPLE/ BLK RIGHT REAR (-) 6 15 RIGHT FRONT HIGH LEVEL (+) GRAY

BLACK GROUND 5 14 LEFT REAR LOW LEVEL (+) GREEN/ RED

BLUE POWER ANTENNA 4 13 LEFT REAR HIGH LEVEL (+) GREEN

ORANGE ILLUMINATION/ DIMMER 3 12 RIGHT REAR LOW LEVEL (+) PURPLE/ RED

BLUE/WHITE AMP TRIGGER 2 11 RIGHT REAR HIGH LEVEL (+) PURPLE

RED IGNITION/ SWITCHED 1 10 BATTERY YELLOW

Pacific Accessory Corporation – 835 835 3233 1502 S. Santa Fe Street, Santa Ana, CA 92705Voice: 714- - -3133 Fax: 714 -

Cables for adding or replacing factory amplifier.

Installation instructions for cables on list “C”

This “C” cable, is used when replacing or adding aftermarket amplifiers to a factory amplified system. (the cable

model # AMP-RCA is also required) This cable plugs in between the factory radio and the dash harness that was removed

from the factory radio. The 18 pin connector then plugs into the OEM-1. The factory system remains unchanged using this

cable. The ADD-UNV cable is used for universal connection to the vehicle harness for vehicles not listed. (splicing required)

Audio should be at a low level when using this cable.

Use the AMP- -RCA cable connected to the 16 pin connector of the OEM-1 to connect your aftermarket amplifier. The AMP

RCA provides 2 pair of female RCA jacks and a remote turn on lead.

Installation instructions for the AMP-RCA cable

This cable is used when replacing or adding aftermarket amplifiers to a factory amplified system. (the appropriate

cable from list “C” is also required) The AMP-RCA cable connects to the 16 pin connector of the OEM-1 and provides 2 pair

of female RCA jacks and a remote turn on lead for connection to your aftermarket amplifier.

Produkt Specifikationer

Mærke:	PAC
Kategori:	Ikke kategoriseret
Model:	AOEM-FRD24

Har du brug for hjælp?

Hvis du har brug for hjælp til PAC AOEM-FRD24 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret PAC Manualer

PAC CAM-GM51 Manual

11 Juli 2025

PAC TY1A-RS Manual

11 Juli 2025

PAC SR-F15009HX Manual

10 Juli 2025

PAC SRK-RAM13HX Manual

10 Juli 2025

PAC AAI-TY3 Manual

30 Juni 2025

PAC SRK-GM14HX Manual

10 Marts 2025

19 Februar 2025

19 Februar 2025

19 Februar 2025

19 Februar 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Advantech MIC-3811 Manual

30 Juli 2025

Intermatic EI230W Manual

30 Juli 2025

Rockboard LED Light V2 Manual

30 Juli 2025

Advantech USB-5817 Manual

30 Juli 2025

Electro Harmonix 9DC-100 Manual

30 Juli 2025

Advantech UTC-515H Manual

30 Juli 2025

Extron MGP 641 xi 5K Manual

30 Juli 2025

Festo EMME-AS-80-M-LS-AMB Manual

30 Juli 2025

Tiptop Audio Octogain Manual

30 Juli 2025

Artec SE-ADL Manual

30 Juli 2025