PAC AP4-CH42 Manual

PAC Ikke kategoriseret AP4-CH42

Læs gratis den danske manual til PAC AP4-CH42 (6 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 56 personer og har en gennemsnitlig bedømmelse på 4.5 stjerner ud af 28.5 anmeldelser. Har du et spørgsmål om PAC AP4-CH42, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/6

PAC-audio.com Page 1

Rev 1

2/5/2024

Advanced Amplier Interface for

Chrysler / Dodge / Jeep / RAM

AP4-CH42

The AP4-CH42 provides a 6-channel pre-amp output for use with aftermarket audio equipment. Using the full range, xed

level head unit output, in conjunction with CAN messages, the AP4-CH42 delivers a variable 5v RMS pre-amp output with

fading, balance, equalization, and level control capabilities. The module also retains all audio from other vehicle features

such as factory navigation prompts, Bluetooth, uConnect, and parking sensor chimes. A data controlled remote amplier

turn on wire is also provided by the AP4-CH42. When used in conjunction with the APA-TOS1 (sold separately), the module

can provide a variable 2-channel ber optic digital audio output (TOSLINK).

Introduction and Features

Important Notes

1. Compatible with both amplied and non-amplied factory systems.

• Amplied Vehicles

• Compatible with all data-bus controlled amplied systems, no matter the screen size (including the 12" screen). To

identify these systems, look for logos on door speakers, tweeters, dash speakers or the subwoofer to conrm if the

vehicle has an amplied system (Alpine & Harmon Kardon). Some vehicles may not always have branded systems.

Unbranded amplied systems are generally identied by locating a center channel speaker or subwoofer

• Non-Amplied Vehicles

• Jeep Wrangler: Compatible with all screen sizes (5", 7" and 8.4").

• All other models: Only compatible in vehicles equipped with the 7" or 8.4" screen. Vehicles equipped with the 5"

screen are not compatible.

• If you are installing the AmpPRO in a vehicle that is not equipped with a factory amplier, you must add an amplier

to the vehicle's speakers, as the factory radio will no longer have a 4 channel variable output after it has been re-

congured by the AmpPRO. For example, you can not add only a subwoofer to a non-amplied vehicle, as the radio

will no longer power the cabin speakers properly.

• Non-amplied vehicles equipped with an Active Noise Cancellation (ANC) system require the ANC module to be

bypassed. This can be done manually or with the ANC bypass harness ANC-CH01. See page 2 Step 6d to re-congure

the factory radio.

2. If a factory amplier is present, it must remain connected and in the vehicle after the AmpPRO has been installed.

3. The remote output is rated at 2A of current. If more current is needed an external relay must be used.

4. Channels 5 and 6 are non-fading outputs. The output level of channels 5 and 6 can be controlled using the supplied level

control knob.

5. The chime volume and minimum volume levels are set to 0 dB by default. If you are happy with this level in your particular

application, additional adjustment is not required. Please refer to the Setup and Conguration section on page 2 for more details.

6. The level control knob must be connected in order to manually adjust the chime volume and minimum volume settings.

7. The factory radio's speed controlled volume and surround sound mode are not supported by the AP4 outputs.

8. When using the TOSLINK output (APA-TOS1 sold separately), DIP switch 1 must be on in order for all warning chimes to be

heard through the sound system (see page 2 Step 6a for details).

9. No adjustments can be made manually using the programming button, or the factory SWC when the module is connected to

a PC.

Module Layout

Interface Connector 1

Expansion Port

Programming Button

Feature Select

DIP switches

Non-Fading Level Control

Knob Connection

USB Connection

LED 1

TOSLINK Output

(APA-TOS1 sold separately)

Front Output

Ch. 1(L) and 2(R)

Rear Output

Ch. 3(L) and 4(R)

Non-Fading Output

Ch. 5(L) and 6(R)

LED 2

Produkt Specifikationer

Mærke:	PAC
Kategori:	Ikke kategoriseret
Model:	AP4-CH42

Har du brug for hjælp?

Hvis du har brug for hjælp til PAC AP4-CH42 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret PAC Manualer

PAC CAM-GM51 Manual

11 Juli 2025

PAC TY1A-RS Manual

11 Juli 2025

PAC SR-F15009HX Manual

10 Juli 2025

PAC SRK-RAM13HX Manual

10 Juli 2025

PAC AAI-TY3 Manual

30 Juni 2025

PAC SRK-GM14HX Manual

10 Marts 2025

19 Februar 2025

19 Februar 2025

19 Februar 2025

19 Februar 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Waterstone 7800 Manual

11 December 2025

Kwikset 258 Manual

11 December 2025

Schlage F170 Manual

11 December 2025

Moen Align 7565EV Manual

11 December 2025

Energy Sistem ESG M3 Neon Manual

11 December 2025

ALNO MC10244 Manual

11 December 2025

JET TAK-ZX Manual

11 December 2025

Crosley Nashville CF1165 Manual

11 December 2025

Waterstone 1455 Manual

11 December 2025

Laica NE2015 Manual

11 December 2025