Page 1
Rev. 070717
$GYDQFHG$PSOL¿HU,QWHUIDFH
IRU)RUG/LQFROQ
AP4-FD11
The AP4-FD11 provides a 6-channel pre-amp output for use with aftermarket audio equipment. Using the full range,
¿[HGOHYHOKHDGXQLWRXWSXWLQFRQMXQFWLRQZLWK&$1PHVVDJHVWKH$3)'GHOLYHUVDYDULDEOHY506SUHDPS
RXWSXWZLWKIDGLQJEDODQFHHTXDOL]DWLRQDQGOHYHOFRQWUROFDSDELOLWLHV7KHPRGXOHDOVRUHWDLQVDOODXGLRIURPRWKHU
YHKLFOHIHDWXUHVVXFKDVIDFWRU\QDYLJDWLRQSURPSWV%OXHWRRWK6<1&DQGSDUNLQJVHQVRUFKLPHV A data controlled
UHPRWHDPSOL¿HUWXUQRQZLUHLVDOVRSURYLGHGE\WKH$3)':KHQXVHGLQFRQMXQFWLRQZLWKWKH$3$726VROG
VHSDUDWHO\WKHPRGXOHFDQSURYLGHDYDULDEOHFKDQQHO¿EHURSWLFGLJLWDODXGLRRXWSXW726/,1.
Introduction and Features
Important Notes
1. This interface is only compatible in vehicles equipped with a data bus controlled premium sound system. To verify
compatibility, look for a Sony or THX badge on the door speakers, center speaker, or factory sub woofer. If none of these
brands are shown, check for the presence of a center speaker or sub woofer.
2. 7KHIDFWRU\DPSOL¿HUPXVWUHPDLQFRQQHFWHGDQGLQWKHYHKLFOHDIWHUWKH$PS352KDVEHHQLQVWDOOHG
3. 7KHUHPRWHRXWSXWLVUDWHGDW$RIFXUUHQW,IPRUHFXUUHQWLVQHHGHGDQH[WHUQDOUHOD\PXVWEHXVHG
4. Channels 5 and 6 are non-fading outputs. The output level of channels 5 and 6 can be controlled using the supplied level
control knob.
5. The chime volume and minimum volume levels are set to 0 dB by default. If you are happy with this level in your particular
DSSOLFDWLRQWKHQDGGLWLRQDODGMXVWPHQWLVQRWUHTXLUHG3OHDVHUHIHUWRWKH6HWXSDQG&RQ¿JXUDWLRQVHFWLRQRQSDJHIRU
more details.
6. You can only use the factory seek / track buttons to activate the chime and minimum volume adjustment in vehicles
equipped with the factory center stack radio.
7. The chime volume only controls the level of the radio button beep. This can be turned off in the radio settings menu.
8. The level control knob must be connected in order to manually adjust the chime volume and minimum volume settings.
9. 7KHIDFWRU\UDGLRVVSHHGFRQWUROOHGYROXPHDQGVXUURXQGVRXQGPRGHDUHQRWVXSSRUWHGE\WKH$3RXWSXWV
10. No adjustments can be made manually using the programming button, or the factory SWC when the module is connected to
D3&
Wiring Connection Chart
To Aftermarket
Amplier
Non-FadingRearFront
1(L) 2(R) 4(R) 5(L) 6(R)3(L)
Remote Turn On Output
2A Max Output
To Vehicle
HarnessTo Radio
Non-Fading
Level Control
Knob
AP4-FD11-HAR
