PAC APSUB-CH41 Manual

PAC Ikke kategoriseret APSUB-CH41

Læs gratis den danske manual til PAC APSUB-CH41 (6 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 31 personer og har en gennemsnitlig bedømmelse på 4.6 stjerner ud af 16 anmeldelser. Har du et spørgsmål om PAC APSUB-CH41, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/6
© 2020 AAMP Global. All rights reserved. PAC is a Power Brand of AAMP Global.
PAC-Audio.com
C
Page 1
Rev: V1
Date: 091120
Advanced Subwoofer Amplier Interface
for Select Chrysler / Dodge / Jeep Vehicles
APSUB-CH41
To Aftermarket
Amplier
Subwoofer Outputs
Remote Turn On Output
2A Max Output
APSUB-CH41-HAR
To Radio To Vehicle
Harness
Non-Fading
Level Control
Knob
Introduction and Features
Important Notes
Wiring Connection Chart
To Factory
Amplier
To Amplier
Harness
ANC-CH02-HAR
The aftermarket amplier must have a very solid ground and the amplier power/ground connections
should be made before connecting the RCA's or Remote Turn On to the APSUB-CH41
The APSUB-CH41 provides a 2-channel non-fading pre-amp output for use with an aftermarket amplier and
subwoofer. Using the full range, xed level head unit output, in conjunction with CAN messages, the APSUB-CH41
delivers a low pass variable 5v RMS pre-amp output with bass equalization and level control capabilities. The signal
has a 350Hz / 24dB Linkwitz-Riley low pass lter applied. A data controlled remote amplier turn on wire is also
provided by the APSUB-CH41.
1. This interface is only compatible in vehicles equipped with a data-bus controlled amplied sound system. To verify
compatibility, look for an Alpine, Beats, or Harmon Kardon badge on the door speakers, center speaker, or factory
subwoofer. If none of these brands are shown; check for the presence of a center speaker or subwoofer.
2. The factory amplier must remain connected, and in the vehicle after the APSUB-CH41 has been installed.
3. The remote output is rated at 2A of current. If more current is needed an external relay must be used.
4. The subwoofer outputs are non-fading. The output level of the subwoofer channel can be controlled using the supplied
level control knob. If the level control knob is not connected the output level will default to 100%.
5. The minimum volume level is set to a default. If you are happy with this level in your particular application then additional
adjustment is not required. Please refer to the Setup and Conguration section on page 2 for more details.
6. The level control knob must be connected in order to manually adjust the minimum volume setting.
7. No adjustments can be made manually using the programming button or the factory SWC when the module is connected
to a PC.
8. If the vehicle is equipped with Active Noise Cancellation (ANC), the ANC can be disabled using the included ANC-CH02
harness. See page 3.
© 2020 AAMP Global. All rights reserved. PAC is a Power Brand of AAMP Global.
PAC-Audio.com
C
Page 2
Rev: V1
Date: 091120
Advanced Subwoofer Amplier Interface
for Select Chrysler / Dodge / Jeep Vehicles
APSUB-CH41
Setup and Conguration
1. Turn the ignition on. LED 1 on the interface will turn on and the +12v remote output will turn on.
2. Set the amp gain(s) to the desired level. We recommend using an oscilloscope and test tones to set the amp gain(s).
Please refer to the MECP Advanced study guide (p. 360) if you are unfamiliar with this process.
3. Check volume, balance, fade and EQ settings.
4. If you would like to adjust the minimum volume, do so using one of the methods outlined on the next page. If you are happy
with the default levels, no adjustments are necessary.
Manually Setting the Minimum Volume (optional)
If the minimum volume of the radio (factory radio volume level 1) is too loud or too quiet, you can manually set the level of the
minimum volume using either the programming button on the side of the interface or the radio dash panel controls. If you would
like to set the minimum volume using the AmpPRO PC app, please proceed to the AmpPRO PC app section.
Installation
DIP
1 2 3 4
ON
No Function No Function No Function5v / 4v Preout
1 2 3 4
Set DIP switches to the ON position to activate the corresponding features.
Set DIP switches to the OFF position for any features that are not desired.
Module Layout
Interface Connector 1
Expansion Port
Programming Button
Feature Select
DIP switches
Non-Fading Level Control
Knob Connection
USB Connection
LED 1
Subwoofer Output
LED 2
1. Remove factory radio.
2. Disconnect the main 52-pin factory harness connector from radio.
3. Connect APSUB harness to vehicle harness.
4. Connect APSUB harness to factory radio.
5. Set any feature DIP switches that apply to your install.
a. Set DIP switch 2 on (down) to lower the RCA output voltage to 4v. Leave DIP switch 2 off (up) to keep the
RCA output voltage at 5v.
b. DIP switches 1, 3, and 4 are not used.
6. Connect the APSUB harness to the module.
7. Connect the level control knob to the module and install in an accessible location.
8. onnect the signal cables and remote input from After the aftermarket amplier power/ground connections are made, c
the aftermarket amplier to the APSUB.
9. Reconnect any additional harnesses removed from the radio and reinstall the radio.

Produkt Specifikationer

Mærke: PAC
Kategori: Ikke kategoriseret
Model: APSUB-CH41

Har du brug for hjælp?

Hvis du har brug for hjælp til PAC APSUB-CH41 stil et spørgsmål nedenfor, og andre brugere vil svare dig


Ikke kategoriseret PAC Manualer

PAC

PAC CAM-GM51 Manual

11 Juli 2025
PAC

PAC TY1A-RS Manual

11 Juli 2025
PAC

PAC SR-F15009HX Manual

10 Juli 2025
PAC

PAC SRK-RAM13HX Manual

10 Juli 2025
PAC

PAC AAI-TY3 Manual

30 Juni 2025
PAC

PAC SRK-GM14HX Manual

10 Marts 2025
PAC

PAC C2A-CHY Manual

19 Februar 2025
PAC

PAC MCI-FD22 Manual

19 Februar 2025
PAC

PAC GM6A-RST Manual

19 Februar 2025
PAC

PAC SWI-X Manual

19 Februar 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

IFM

IFM SU9030 Manual

13 September 2025
IFM

IFM O2U554 Manual

13 September 2025
Speco Technologies

Speco Technologies HTi70TM Manual

13 September 2025
QSC

QSC RMXa Manual

13 September 2025
Tineco

Tineco Floor One S2 Series Manual

13 September 2025
Tineco

Tineco Floor One S3 Breeze Manual

13 September 2025
Tineco

Tineco Floor One S5 Steam Manual

13 September 2025
Osram

Osram VX500-CB Manual

13 September 2025
Zelmer

Zelmer ZTS7990 Manual

13 September 2025
Osram

Osram VX250-SP Manual

13 September 2025