PAC APSUB-FD21 Manual

PAC Ikke kategoriseret APSUB-FD21

Læs gratis den danske manual til PAC APSUB-FD21 (5 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 24 personer og har en gennemsnitlig bedømmelse på 4.3 stjerner ud af 12.5 anmeldelser. Har du et spørgsmål om PAC APSUB-FD21, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/5
© 2020 AAMP Global. All rights reserved. PAC is a Power Brand of AAMP Global.
PAC-Audio.com
C
Page 1
Rev: V1
Date: 091120
Advanced Subwoofer Amplier Interface
for Select Ford Vehicles
APSUB-FD21
The APSUB-FD21 provides a 2-channel non-fading pre-amp output for use with an aftermarket amplier and
subwoofer. Using the full range, xed level head unit output, in conjunction with CAN messages, the APSUB-FD21
delivers a low pass variable 5v RMS pre-amp output with bass equalization and level control capabilities. The signal
has a 350Hz / 24dB Linkwitz-Riley low pass lter applied. A data controlled remote amplier turn on wire is also
provided by the APSUB-FD21.
Introduction and Features
Important Notes
1. This interface is only compatible in vehicles equipped with a data bus controlled premium sound system. To verify
compatibility, look for a Sony badge on the door speakers, center speaker, or factory subwoofer, in the 2019-2020
Super Duty trucks and Mustang; look for a B&O badge.
2. The factory amplier must remain connected, and in the vehicle after the APSUB-FD21 has been installed.
3. The remote output is rated at 2A of current. If more current is needed an external relay must be used.
4. The remote output may remain active once the key has been removed if the vehicle needs to pass chime or SYNC audio.
5. The subwoofer outputs are non-fading. The output level of the subwoofer channel can be controlled using the supplied level
control knob. If the level control knob is not connected the output level will default to 100%.
6. The minimum volume level is set to a default. If you are happy with this level in your particular application then additional
adjustment is not required. Please refer to the Setup and Conguration section on page 2 for more details.
7. Ford Focus: You cannot use the steering wheel controls to activate the minimum volume adjustment.
8. The level control knob must be connected in order to manually adjust the minimum volume settings.
9. The factory radio's speed controlled volume and surround sound mode are not supported by the APSUB-FD21 outputs.
10. No adjustments can be made manually using the programming button, or the factory SWC when the module is connected to
a PC.
To Aftermarket
Amplier
Subwoofer Outputs
Remote Turn On Output
2A Max Output
To Vehicle
Harness
To Radio
To LCD
Screen
Non-Fading
Level Control
Knob
To Vehicle
Harness
AP4-FD21-HAR
The aftermarket amplier must have a very solid ground and the amplier power/ground connections
should be made before connecting the RCA's or Remote Turn On to the APSUB-FD21
© 2020 AAMP Global. All rights reserved. PAC is a Power Brand of AAMP Global.
PAC-Audio.com
C
Page 2
Rev: V1
Date: 091120
Advanced Subwoofer Amplier Interface
for Select Ford Vehicles
APSUB-FD21
Setup and Conguration
1. Turn the ignition on. LED 1 on the interface will turn on and the +12v remote output will turn on.
2. Set the amp gain(s) to the desired level. We recommend using an oscilloscope and test tones to set the amp gain(s).
Please refer to the MECP Advanced study guide (p. 360) if you are unfamiliar with this process.
3. Check volume, balance, fade and EQ settings.
4. If you would like to adjust the minimum volume, do so using one of the methods outlined below. If you are happy with the
default level, no adjustments are necessary.
Manually Setting the Minimum Volume
If the minimum volume of the radio (factory radio volume level 1) is too loud, you can manually set the level of the minimum
volume using either the programming button on the side of the interface or the factory SWC. If you would like to set the
minimum volume using the AmpPRO app, please proceed to the AmpPRO App section.
Installation
Module Layout
Interface Connector 1
Expansion Port
Programming Button
Feature Select
DIP switches
Non-Fading Level Control
Knob Connection
USB Connection
LED 1
Subwoofer Output
LED 2
1. Remove factory radio and LCD screen.
2. Disconnect the 52-pin harness from the LCD screen and the 24-pin harness from the radio.
3. Connect APSUB harnesses to vehicle harnesses.
4. Connect APSUB harnesses to LCD screen and factory radio.
5. Set any feature DIP switches that apply to your install.
a. Set DIP switch 2 on (down) to lower the RCA output voltage to 4v. Leave DIP switch 2 off (up) to keep the RCA output
voltage at 5v.
b. DIP switch 1 is not used. DIP switches 3 and 4 are used for additional troubleshooting. (See page 5 for more details).
6. Connect the APSUB harness to the module.
7. Connect the level control knob to the module and install in an accessible location.
8. connect the signal cables and remote input from the After the aftermarket amplier power/ground connections are made,
aftermarket amplier to the APSUB.
9. Reconnect any additional harnesses removed from the radio and reinstall the radio.
DIP
1 2 3 4
ON
No Function Troubleshooting* Troubleshooting*5v / 4v Preout
1 2 3 4
Set DIP switches to the ON position to activate the corresponding features.
Set DIP switches to the OFF position for any features that are not desired.
* See troubleshooting section on page 5 for more details

Produkt Specifikationer

Mærke: PAC
Kategori: Ikke kategoriseret
Model: APSUB-FD21

Har du brug for hjælp?

Hvis du har brug for hjælp til PAC APSUB-FD21 stil et spørgsmål nedenfor, og andre brugere vil svare dig


Ikke kategoriseret PAC Manualer

PAC

PAC CAM-GM51 Manual

11 Juli 2025
PAC

PAC TY1A-RS Manual

11 Juli 2025
PAC

PAC SR-F15009HX Manual

10 Juli 2025
PAC

PAC SRK-RAM13HX Manual

10 Juli 2025
PAC

PAC AAI-TY3 Manual

30 Juni 2025
PAC

PAC SRK-GM14HX Manual

10 Marts 2025
PAC

PAC C2A-CHY Manual

19 Februar 2025
PAC

PAC MCI-FD22 Manual

19 Februar 2025
PAC

PAC GM6A-RST Manual

19 Februar 2025
PAC

PAC SWI-X Manual

19 Februar 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

IFM

IFM SU9030 Manual

13 September 2025
IFM

IFM O2U554 Manual

13 September 2025
Speco Technologies

Speco Technologies HTi70TM Manual

13 September 2025
QSC

QSC RMXa Manual

13 September 2025
Tineco

Tineco Floor One S2 Series Manual

13 September 2025
Tineco

Tineco Floor One S3 Breeze Manual

13 September 2025
Tineco

Tineco Floor One S5 Steam Manual

13 September 2025
Osram

Osram VX500-CB Manual

13 September 2025
Zelmer

Zelmer ZTS7990 Manual

13 September 2025
Osram

Osram VX250-SP Manual

13 September 2025