PAC APSUB-TY13 Manual

PAC Ikke kategoriseret APSUB-TY13

Læs nedenfor 📖 manual på dansk for PAC APSUB-TY13 (6 sider) i kategorien Ikke kategoriseret. Denne guide var nyttig for 18 personer og blev bedømt med 4.6 stjerner i gennemsnit af 9.5 brugere

Download PDF
Side 1/6
© 2021 AAMP Global. All rights reserved. PAC is a Power Brand of AAMP Global.
PAC-audio.com
C
Page 1
Rev: 2
Date: 052721
®
Advanced Subwoofer Amplier Interface
for Select Toyota and Lexus Applications
APSUB-TY13
The APSUB-TY13 provides a 2-channel non-fading output for use with an aftermarket amplier and subwoofer. Using the
full range, xed level head unit output, in conjunction data bus messages, the APSUB-TY13 delivers a variable 5v RMS
pre-amp output with bass equalization and level control capabilities. The signal has a 350Hz / 24dB Linkwitz-Riley low
pass lter applied. A data controlled remote amplier turn on wire is also provided by the APSUB-TY13.
Introduction and Features
Important Notes
1. Only compatible in vehicles equipped with a data bus controlled premium sound system. To verify compatibility in Toyota,
look for a JBL logo on the radio. In Lexus, compatible applications will have a center channel or factory subwoofer.
2. Toyota Safety Connect / Lexus Enform (SOS) audio mute can be retained. See the page 3 for detailed instructions.
3. The factory radio's speed controlled volume, DSP, and surround sound mode are not supported by the APSUB outputs.
4. Thefactoryampliermustremainconnected,andinthevehicleaftertheAPSUBhasbeeninstalled.
5. The radio's minimum volume level is set to 0 dB by default. If you are happy with this level in your particular application,
additionaladjustmentisnotrequired.PleaserefertotheSetupandCongurationsectiononpage3formoredetails.
6. The remote output is rated at 2A of current. If more current is needed, an external relay must be used.
7. The subwoofer channels are non-fading outputs. The output level of subwoofer channels can be controlled using the
supplied level control knob.
Wiring Connection Chart
To Aftermarket
Amplier
Subwoofer Outputs
Non-Fading
Level Control
Knob
Remote Turn On Output (2A Max)
SOS Mute ( - Trigger Input )
GRAY GRAY
BLACK BLACK
28-pin
10-pin
© 2021 AAMP Global. All rights reserved. PAC is a Power Brand of AAMP Global.
PAC-audio.com
C
Page 2
Rev: 2
Date: 052721
®
Advanced Subwoofer Amplier Interface
for Select Toyota and Lexus Applications
APSUB-TY13
Installation
1. Remove the factory radio.
2. Disconnect the 28-pin harness and the 10-pin connectors from the
radio.
3. Ensure that you only remove the 28-pin connector that is closest
to the 10-pin connector, the correct 28-pin connector will be either
gray or white depending on the vehicle. There is another 28-pin
connector on the radio that will not be used. See Figure 1.
4. Connect the APSUB harnesses to the vehicle harnesses.
5. Connect the APSUB harnesses to the factory radio.
6. Set any feature DIP switches that apply to your install:
a DIP switch 1 is not used and should remain off (up).
b. Set DIP switch 2 on (down) to lower the RCA output voltage to 4v.
Leave DIP switch 2 off (up) to keep the RCA output voltage at 5v.
c. *Set DIP switch 3 on (down) to increase the input gain for the
vehicles listed on Page 3. All others, leave DIP switch 3 off (up)
to keep the input gain at the default value.
d. DIP switch 4 is not used and should remain off (up).
7. Connect the APSUB harness to the module.
8. Connect the level control knob to the module and install in an
accessible location.
9. Connect the signal cables and remote input from the aftermarket
amplier.
10. The Yellow / Black "SOS Mute" wire will be used in conjunction with
the Safety Connect / Lexus Enform (SOS) Retention. See Page 3
for more details.
DIP
1234
ON
Not Used 5v / 4v Preout Input Gain Setting* Not Used
1 2 3 4
Set DIP switches to the ON position to activate the corresponding features.
Set DIP switches to the OFF position for any features that are not desired.
Module Layout
LED 1
Interface Connector 1
Expansion Port
Programming Button
Feature Select
DIP switches
Non-Fading Level Control
Knob Connection
USB Connection
Subwoofer Outputs
LED 2
Fig.1
10-pin 28-pin NOT USED
The aftermarket amplier must have a very solid ground and the amplier power/ground
connections should be made before connecting the RCA's or Remote Turn On
to the APSUB-TY13

Produkt Specifikationer

Mærke: PAC
Kategori: Ikke kategoriseret
Model: APSUB-TY13

Har du brug for hjælp?

Hvis du har brug for hjælp til PAC APSUB-TY13 stil et spørgsmål nedenfor, og andre brugere vil svare dig


Ikke kategoriseret PAC Manualer

PAC

PAC OnStar OS-311b Manual

17 Februar 2025
PAC

PAC BT-SWC-NI1 Manual

11 Februar 2025
PAC

PAC OnStar OS-311 Manual

11 Februar 2025
PAC

PAC LCCH21 Manual

11 Februar 2025
PAC

PAC APSUB-TY13 Manual

28 December 2024
PAC

PAC RP4-GM31 Manual

6 September 2024
PAC

PAC NU-CTS2 Manual

6 September 2024
PAC

PAC TR7 Manual

6 September 2024
PAC

PAC OS-5 Manual

6 September 2024
PAC

PAC NDK735MG Manual

29 August 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Ikea

Ikea RAMSHULT 404.305.50 Manual

6 Juni 2025
Celly

Celly USBCUSBCNYL Manual

6 Juni 2025
Vocopro

Vocopro DVG-888K II Manual

6 Juni 2025
Wiesenfield

Wiesenfield WIE-AT-300 Manual

6 Juni 2025
Mitsubishi

Mitsubishi WB-PA3 Manual

6 Juni 2025
HMS Premium

HMS Premium STR05 Manual

6 Juni 2025
Fulgor Milano

Fulgor Milano F7RT30S1 Manual

6 Juni 2025
MSW

MSW -PBR-1270 Manual

6 Juni 2025
Royal Catering

Royal Catering RCAT-100/50-WTP Manual

6 Juni 2025
Ikea

Ikea DAJLIEN 805.526.72 Manual

6 Juni 2025