PAC BCI-CH41 Manual

PAC Ikke kategoriseret BCI-CH41

Læs gratis den danske manual til PAC BCI-CH41 (8 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 13 personer og har en gennemsnitlig bedømmelse på 4.8 stjerner ud af 7 anmeldelser. Har du et spørgsmål om PAC BCI-CH41, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/8

Reverse Camera Input and Navigation Unlock

Interface for Chrysler / Dodge / Jeep / RAM Vehicles

BCI-CH41 (v2)

PAC-audio.com

Rev: V3

Date: 040918 Page 1

The BCI-CH41 will program your Chrysler / Dodge / Jeep / RAM radio to allow the addition of a reverse camera or Rear

Media input if the vehicle is not equipped with these features from the factory (reverse camera and video source sold

separately). The BCI-CH41 will also allow the factory navigation features of your radio to be used by the passenger at

anytime. The interface can also be congured to add even more features, such as: Blind Spot Cameras, Front Camera,

Eco Mode Memory, Auto Start / Stop Memory, Sport Mode Memory, Remote Start Climate Restore, Steering Wheel

Control (SWC) swap, EQ Presets, and three programmable 12v outputs. The BCI-CH41 also has on-demand activation

of rear or front camera.

Introduction & Features

Important Notes

1. These instructions only apply to rmware version 14 and harness version 3. The versions can be found on a small white sticker on the

interface and harness.

2. RAM trucks equipped with a manual transmission will not support the forced Reverse Camera or Reverse Output Trigger features.

3. The Jeep Cherokee and Chrysler 200 will not support the addition of Reverse Camera or Rear Media input.

4. 2017 Dodge Charger, Challenger, Chrysler 300 and vehicles equipped with the 5” screen do not support the addition of Rear Media Mode.

5. It is very important to follow the exact sequence of installation steps as listed below. Failure to do so will result in the interface not

working as intended.

6. If you change the DIP switch settings, you must disconnect and reconnect power for the change to take effect

7. The navigation unlock feature must be activated by the SWC every time the key is cycled.

8. The VS41 video switcher, AVS21 A/V switcher, or possibly both, must be used in order to use more than one video source with the

BCI-CH41.

9. If navigation is being used and the camera input is engaged UNDER 20 MPH, it will affect the navigation guidance until the camera

input is switched off.

10. Vehicles without audio SWC (located on the back of the steering wheel) will not support the Navigation Unlock or SWC Swap features.

11. You cannot force the front camera when the reverse camera is active as reverse camera always takes priority.

1. Set DIP switches to the ON position that correspond with the features you want to add. Feature DIP switches (1-3) must be set before

connecting the interface to the vehicle harness.

a. DIP switch 4 - Turning ON DIP switch 4 will allow you to access the Feature Settings Menu through the vehicles Multi Function Display

to turn additional features On / Off. These features can also be set using the BCI App. Please see Page 6 for a full list and description

of each of the BCI features.

2. At this point, you can plug the BCI into a Windows PC and set up the programmable outputs, blind spot and / or front camera operation,

as well as enable any other features of the BCI using the BCI App. See page 6 for more details on the BCI app.

3. Remove the factory radio and disconnect the factory harness(es).

4. Connect the factory harness into the female connector on the BCI-CH41 harness.

Installation Steps

Module Layout

Reset Button

USB Port

Feature Select

DIP switches

LED 1

LED 2

Interface

Connector 1

Expansion Port

Interface Connector 2

Reverse Camera Navigation Unlock Feature Settings MenuRear Media

1 2 3 4

Set DIP switches to the ON position to activate the corresponding features.

Set DIP switches to the OFF position for any features that are not desired.

Produkt Specifikationer

Mærke:	PAC
Kategori:	Ikke kategoriseret
Model:	BCI-CH41

Har du brug for hjælp?

Hvis du har brug for hjælp til PAC BCI-CH41 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret PAC Manualer

PAC CAM-GM51 Manual

11 Juli 2025

PAC TY1A-RS Manual

11 Juli 2025

PAC SR-F15009HX Manual

10 Juli 2025

PAC SRK-RAM13HX Manual

10 Juli 2025

PAC AAI-TY3 Manual

30 Juni 2025

PAC SRK-GM14HX Manual

10 Marts 2025

19 Februar 2025

19 Februar 2025

19 Februar 2025

19 Februar 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Waterstone 7800 Manual

11 December 2025

Kwikset 258 Manual

11 December 2025

Schlage F170 Manual

11 December 2025

Moen Align 7565EV Manual

11 December 2025

Energy Sistem ESG M3 Neon Manual

11 December 2025

ALNO MC10244 Manual

11 December 2025

JET TAK-ZX Manual

11 December 2025

Crosley Nashville CF1165 Manual

11 December 2025

Waterstone 1455 Manual

11 December 2025

Laica NE2015 Manual

11 December 2025