PAC CAM-NI1 Manual

PAC Ikke kategoriseret CAM-NI1

Læs gratis den danske manual til PAC CAM-NI1 (3 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 20 personer og har en gennemsnitlig bedømmelse på 4.3 stjerner ud af 10.5 anmeldelser. Har du et spørgsmål om PAC CAM-NI1, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/3

CAM-NI1

Reverse Camera T-Harness

for Select VehiclesNissan

Rev. 112817

Introduction & Features

Installation:

The CAM-NI1 is a reverse camera T-harness that gives the ability to add a reverse camera input for compatible Nissan

radios. Simple plug and play installation.

1. Disassemble dash and remove the radio.

2. Disconnect the 32 pin connector from the back of the factory radio (if equipped) and install the T-harness.

3. Connect the RCA from the aftermarket camera to the female RCA located in the T-harness

3. The OEM radio, when connected to this harness, may provide a +6v power output on the Yellow wire if needed Mos. t

aftermarket cameras require +12v for power, if your camera requires +12v then you will need to nd a reliable source of

+12 volt ACC power. If not being used please insulate the Yellow wire.

4. To function properly the camera must have power before the vehicle is placed into reverse, so using the reverse lamp as a

power source is not recommended for proper functionality.

5. It may be necessary to provide a reverse trigger to the radio. Normally a reverse trigger is provided by the vehicle

manufacturer, as long as the camera has power when the vehicle is placed into reverse, the radio should automatically switch

to the reverse camera. In the event that the radio does not automatically switch to the reverse camera a +12v reverse signal

will need to be added to Pin 30 of the 32 pin connector. To do this, cut the Green / Purple wire in pin 30 in half and apply the

+12v reverse signal to the radio side of the cut wire. See Fig 1 and Fig 2.

Adding a reverse camera to an OEM radio:

Fig. 1

Fig. 2

PAC-audio.com

VEHICLE

SIDE

RADIO

SIDE

Produkt Specifikationer

Mærke:	PAC
Kategori:	Ikke kategoriseret
Model:	CAM-NI1

Har du brug for hjælp?

Hvis du har brug for hjælp til PAC CAM-NI1 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret PAC Manualer

PAC CAM-GM51 Manual

11 Juli 2025

PAC TY1A-RS Manual

11 Juli 2025

PAC SR-F15009HX Manual

10 Juli 2025

PAC SRK-RAM13HX Manual

10 Juli 2025

PAC AAI-TY3 Manual

30 Juni 2025

PAC SRK-GM14HX Manual

10 Marts 2025

19 Februar 2025

19 Februar 2025

19 Februar 2025

19 Februar 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

IFM SU9030 Manual

13 September 2025

IFM O2U554 Manual

13 September 2025

Speco Technologies HTi70TM Manual

13 September 2025

QSC RMXa Manual

13 September 2025

Tineco Floor One S2 Series Manual

13 September 2025

Tineco Floor One S3 Breeze Manual

13 September 2025

Tineco Floor One S5 Steam Manual

13 September 2025

Osram VX500-CB Manual

13 September 2025

Zelmer ZTS7990 Manual

13 September 2025

Osram VX250-SP Manual

13 September 2025