PAC LPHFD21 Manual

PAC Ikke kategoriseret LPHFD21

Læs gratis den danske manual til PAC LPHFD21 (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 11 personer og har en gennemsnitlig bedømmelse på 4.1 stjerner ud af 6 anmeldelser. Har du et spørgsmål om PAC LPHFD21, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/2
© 2021 AAMP Global. All rights reserved. PAC is a Power Brand of AAMP Global.
PAC-audio.com
C
Rev.7
1/5/2022
LPH Harness Instruction Guide
®
Wiring Connection Chart (All Models)
MODELS:
• LPA-E4
• LPA2.4 / LPA2.2
• LPA1.4 / LPA1.2
Important Note: This harness is provided
with a inline fuse installed. Please remove
prior to install and reinsert once nished.
If your vehicle does not provide ACC
source your harness will not have a
"RED" wire to connect.
It will use DC O󰀨set to turn on as well
as trigger the "REM OUT" on the LPA.
On LPA-E4 there will be a jumper that
you can move based on your application.
This harness is designed to work on
OEM NON-AMPLIFIED systems.
Connect the RED BUTT Connector to
the aftermarket system turn on for your
ampliers.
Fully open terminals
before inserting wire.
© 2021 AAMP Global. All rights reserved. PAC is a Power Brand of AAMP Global.
PAC-audio.com
C
Rev.7
1/5/2022
LPH Harness Instruction Guide
®
Example Installation - 4-Channel Amplier - (HARNESS CUT REQUIRED)
Example Installation - Mono Amplier - (HARNESS CUT NOT REQUIRED)
RCA FROM LPA
"CUT HERE
AND INSULATE"
• Cut the harness close as possible to the
"CUT HERE AND INSULATE" label. You
must insulate wires to prevent damage to
OEM radio.
• The cut speaker wires will need to be
connected to your aftermarket amplier.
(REFER TO LABEL ON HARNESS)
• Please refer to the chart on the rst page
for wiring your loose wires to your LPA.
• This harness is designed to work on OEM
NON-AMPLIFIED systems.
OEM RADIO HARNESS
LPH TO RADIO CONNECTION
LOOSE WIRES TO LPA
REM OUT FROM LPA
DO NOT CUT!!
• If using a 2-Channel input LPA
use the front speaker wires
and insulate the remaining rear
speaker wires.
• DO NOT CUT the speaker wires
inbetween the "CUT HERE"
Lables in order to keep the
factory speakers functional.
• This harness is designed to
work on OEM NON-AMPLIFIED
systems.
OEM RADIO HARNESS
LOOSE WIRES TO LPA
"CUT HERE AND
INSULATE"
"CUT HERE AND CONNECT TO
AFTERMARKET AMPLIFIER"
LPH TO RADIO CONNECTION
RCA FROM LPA
REM OUT FROM LPA
AFTERMARKET AMPLIFIER
AFTERMARKET AMPLIFIER
"CUT HERE AND CONNECT TO
AFTERMARKET AMPLIFIER"
(CUT SPEAKER WIRES)

Produkt Specifikationer

Mærke: PAC
Kategori: Ikke kategoriseret
Model: LPHFD21

Har du brug for hjælp?

Hvis du har brug for hjælp til PAC LPHFD21 stil et spørgsmål nedenfor, og andre brugere vil svare dig


Ikke kategoriseret PAC Manualer

PAC

PAC CAM-GM51 Manual

11 Juli 2025
PAC

PAC TY1A-RS Manual

11 Juli 2025
PAC

PAC SR-F15009HX Manual

10 Juli 2025
PAC

PAC SRK-RAM13HX Manual

10 Juli 2025
PAC

PAC AAI-TY3 Manual

30 Juni 2025
PAC

PAC SRK-GM14HX Manual

10 Marts 2025
PAC

PAC C2A-CHY Manual

19 Februar 2025
PAC

PAC MCI-FD22 Manual

19 Februar 2025
PAC

PAC GM6A-RST Manual

19 Februar 2025
PAC

PAC SWI-X Manual

19 Februar 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Navman

Navman MY500XT Manual

1 August 2025
Navman

Navman FOCUS150 GPS Manual

1 August 2025
Scheppach

Scheppach TW1000 Manual

1 August 2025
Navman

Navman MiVue 750 WIFI Manual

1 August 2025
Navman

Navman MiVue Drive FHD Manual

1 August 2025
Midea

Midea MEC64 Manual

1 August 2025
Navman

Navman MY50T Manual

1 August 2025
Navman

Navman M100 Manual

1 August 2025
Navman

Navman MiVue 770 SAFETY Manual

1 August 2025
Navman

Navman MiVue 790 Manual

1 August 2025