PAC LPHTY02 Manual

PAC Ikke kategoriseret LPHTY02

Læs gratis den danske manual til PAC LPHTY02 (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 26 personer og har en gennemsnitlig bedømmelse på 5.0 stjerner ud af 13.5 anmeldelser. Har du et spørgsmål om PAC LPHTY02, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/2
© 2021 AAMP Global. All rights reserved. PAC is a Power Brand of AAMP Global.
PAC-audio.com
C
Rev.7
1/5/2022
LPH Harness Instruction Guide
®
Wiring Connection Chart (All Models)
MODELS:
• LPA-E4
• LPA2.4 / LPA2.2
• LPA1.4 / LPA1.2
Important Note: This harness is provided
with a inline fuse installed. Please remove
prior to install and reinsert once nished.
If your vehicle does not provide ACC
source your harness will not have a
"RED" wire to connect.
It will use DC O󰀨set to turn on as well
as trigger the "REM OUT" on the LPA.
On LPA-E4 there will be a jumper that
you can move based on your application.
This harness is designed to work on
OEM NON-AMPLIFIED systems.
Connect the RED BUTT Connector to
the aftermarket system turn on for your
ampliers.
Fully open terminals
before inserting wire.
© 2021 AAMP Global. All rights reserved. PAC is a Power Brand of AAMP Global.
PAC-audio.com
C
Rev.7
1/5/2022
LPH Harness Instruction Guide
®
Example Installation - 4-Channel Amplier - (HARNESS CUT REQUIRED)
Example Installation - Mono Amplier - (HARNESS CUT NOT REQUIRED)
RCA FROM LPA
"CUT HERE
AND INSULATE"
• Cut the harness close as possible to the
"CUT HERE AND INSULATE" label. You
must insulate wires to prevent damage to
OEM radio.
• The cut speaker wires will need to be
connected to your aftermarket amplier.
(REFER TO LABEL ON HARNESS)
• Please refer to the chart on the rst page
for wiring your loose wires to your LPA.
• This harness is designed to work on OEM
NON-AMPLIFIED systems.
OEM RADIO HARNESS
LPH TO RADIO CONNECTION
LOOSE WIRES TO LPA
REM OUT FROM LPA
DO NOT CUT!!
• If using a 2-Channel input LPA
use the front speaker wires
and insulate the remaining rear
speaker wires.
• DO NOT CUT the speaker wires
inbetween the "CUT HERE"
Lables in order to keep the
factory speakers functional.
• This harness is designed to
work on OEM NON-AMPLIFIED
systems.
OEM RADIO HARNESS
LOOSE WIRES TO LPA
"CUT HERE AND
INSULATE"
"CUT HERE AND CONNECT TO
AFTERMARKET AMPLIFIER"
LPH TO RADIO CONNECTION
RCA FROM LPA
REM OUT FROM LPA
AFTERMARKET AMPLIFIER
AFTERMARKET AMPLIFIER
"CUT HERE AND CONNECT TO
AFTERMARKET AMPLIFIER"
(CUT SPEAKER WIRES)

Produkt Specifikationer

Mærke: PAC
Kategori: Ikke kategoriseret
Model: LPHTY02

Har du brug for hjælp?

Hvis du har brug for hjælp til PAC LPHTY02 stil et spørgsmål nedenfor, og andre brugere vil svare dig


Ikke kategoriseret PAC Manualer

PAC

PAC OnStar OS-311b Manual

17 Februar 2025
PAC

PAC BT-SWC-NI1 Manual

11 Februar 2025
PAC

PAC OnStar OS-311 Manual

11 Februar 2025
PAC

PAC LCCH21 Manual

11 Februar 2025
PAC

PAC APSUB-TY13 Manual

28 December 2024
PAC

PAC RP4-GM31 Manual

6 September 2024
PAC

PAC NU-CTS2 Manual

6 September 2024
PAC

PAC TR7 Manual

6 September 2024
PAC

PAC OS-5 Manual

6 September 2024
PAC

PAC NDK735MG Manual

29 August 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

AmpliVox

AmpliVox Airvox SW695 Manual

15 Juni 2025
Stiga

Stiga SBC 635 KD Manual

15 Juni 2025
Cleveland

Cleveland 36CGM300 Manual

15 Juni 2025
Gourmia

Gourmia GTF7970 Manual

15 Juni 2025
Planet Audio

Planet Audio P9630B Manual

15 Juni 2025
ORNO

ORNO OR-DOM-YR-934UD Manual

15 Juni 2025
Lavex

Lavex 842CD12VST12 Manual

15 Juni 2025
Marshall

Marshall RCP-PLUS Manual

15 Juni 2025
Hughes & Kettner

Hughes & Kettner BassForce XL Manual

15 Juni 2025
Hughes & Kettner

Hughes & Kettner Red Box Mk III Manual

15 Juni 2025