PAC NU-CTS2 Manual

PAC Ikke kategoriseret NU-CTS2

Læs gratis den danske manual til PAC NU-CTS2 (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 36 personer og har en gennemsnitlig bedømmelse på 5.0 stjerner ud af 18.5 anmeldelser. Har du et spørgsmål om PAC NU-CTS2, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

Pacic Accessory Corporation - Santa Ana, CA 92705

techsupport@pac-audio.com • Voice: 866-931-8021 • Fax: 714-835-3233 • www.pac-audio.com

04-02-12

NU-CTS2

Cadillac CTS

Navigation Unlock

Integration Interface

Installation: Disconnect the black 44-pin main harness from the back of the radio (see g. A) Plug the male connector on the NU-CTS2

harness into the 44-pin port on the back of the radio. Connect the factory 44-pin harness into the female connector on the NU-CTS2 harness.

Plug the Black micro-t 24-pin connector on the NU-CTS2 harness into the NU-CTS2.

2008-2009 Vehicles Only: Locate the vehicles VSS wire in pin 20 of the gray 20-pin plug on the back of the radio (see g. A & B). This wire will

need to be cut then connected as follows: The green/black wire from the NU-CTS2 should be connected to the radio/plug side of the VSS wire

and the green/white wire from the NU-CTS2 should be connected to the vehicle side of the VSS wire.

The NU-CTS2 is a Navigation Unlock integration interface that allows the factory navigation features of

your Cadillac CTS radio or the reverse camera to be used by the passenger at anytime.

Main 44-pin Plug

Gray 20-pin Plug

Installation

Cadillac CTS Controls

Press & hold to

enable/disable

Navigation Unlock

1. Press & Hold the

Source Button

2. Information Center

Displays: Confirm

Safe Use

3. Press the Source

Button Again to

Confirm

4. Repeat Step 1

to De-Activate

Activating the Navigation Unlock

Cadillac CTS: Press and hold the “Source” button on the steering wheel controls (SWC) for two seconds to activate the NU-CTS2. You will hear

one chime and the driver information center on the instrument cluster will display “Conrm Safe Use”. Press the “Source” button on the SWC

again to acknowledge “safe use”, agreeing that use will be performed only by the passenger whenever the vehicle is in

motion, and activate the NU-CTS2. To de-activate the NU-CTS2 simply press and hold the “Source” button on the SWC until two chimes are

heard. The NU-CTS2 text will not be displayed when the OnStar Turn-by-Turn Navigation is being used.PLEASE NOTE:

Cadillac CTS-V: Make sure that both of the mirror control lights are off on the driver door. Press the Up button on the mirror controls to activate

the NU-CTS2. You will hear one chime and the driver information center on the instrument cluster will display “Conrm Safe Use”. Press the

Up button on the mirror controls again to acknowledge “safe use”, agreeing that use will be performed only by the passenger

whenever the vehicle is in motion, and activate the NU-CTS2. To de-activate the NU-CTS2 simply press the Up button on the mirror

control. The NU-CTS2 text will not be displayed when the OnStar Turn-by-Turn Navigation is being used.PLEASE NOTE:

WARNING: In order to avoid distraction, which could lead to an accident, the driver should never utilize systems unlocked by the NU-CTS2 when the

vehicle is in motion. Even when operated by the passenger, the vehicle driver should maintain their attention on the road at all times.

Operation

Pin 20

Cadillac CTS-V Controls

Press Once to

Enable/Disable

Navigation Unlock

Make Sure the Control

Lights Are O.

1. Turn o all

mirror controls

2. Press the

Up Button

2. Information Center

Displays: Confirm

Safe Use

3. Press the Up

Button Again to

Confirm

4. Repeat Step 2

to De-Activate

Pacic Accessory Corporation - Santa Ana, CA 92705

techsupport@pac-audio.com • Voice: 866-931-8021 • Fax: 714-835-3233 • www.pac-audio.com

04-02-12

DISCLAIMER: Under no circumstances shall the manufacture or the distributors of the NU-CTS2 be held liable for claims of any loss or damage,

consequential, direct or indirect, arising from the sale, installation, or use of the NU-CTS2. The manufacture and its distributors will not, nor will they

authorize any representative or any other individual, to assume obligation or liability in relation to the NU-CTS2 other than its replacement.

AGREEMENT: End user agrees to use this product in compliance with the instructions and terms of use above and with all State and Federal

laws. PAC provides instructions and safety warnings with respect to this product and disclaims all liability for any use not in conformity with those

instructions or other misuse of its product. If you do not agree, please discontinue use immediately and return product to place of purchase. This

product is intended for off-road use and passenger use only.

Activating the Reverse Camera Unlock

Activate the navigation unlock using the SWC. Make sure that both control lights

on the rearview mirror controls on the driver door are off and not controlling either

mirror. Press down on the control pad, the rearview camera image will now display

on the navigation screen.

WARNING: In order to avoid distraction, which could lead to an accident,

the driver should never utilize systems unlocked by the NU-CTS2 when the