PAC RP4-CH11 Manual

PAC Ikke kategoriseret RP4-CH11

Læs gratis den danske manual til PAC RP4-CH11 (4 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 19 personer og har en gennemsnitlig bedømmelse på 3.8 stjerner ud af 10 anmeldelser. Har du et spørgsmål om PAC RP4-CH11, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/4
Pacic Accessory Corporation
® | Santa Ana, California 92705 | Ph. 866-931-8021 | support@pac-audio.com
©2011 Pacic Accessory Corporation
www.pac-audio.com
C
RP4-CH11
Radio Replacement & Steering Wheel Control Interface
for Chrysler/Dodge/Jeep Vehicles
Rev. 112811
Introduction & Features
Important Notes
Wiring Connection Chart
Illustration / Schematic
The RP4-CH11 interface allows the replacement of a factory radio in select Chrysler/Dodge/Jeep vehicles with MSCAN or
LSFT-CAN databus radios. Using this interface will retain factory features such as steering wheel controls (SWC) vehicle
entertainment system (VES) and the factory audio amplier whenever the original radio is removed. The RP4-CH11 also
provides data bus driven outputs such as retained accessory power (RAP), vehicle speed sensor (VSS), illumination,
reverse trigger and parking brake.
1. The radio select rotary switch on the side of the interface must be adjusted to the proper radio setting before plugging the
interface into the vehicle (see next page for setting chart).
2. When the interface is rst plugged into the vehicle the LED will ash indicating the auto detect sequence. Once the CAN-BUS
speed is detected the LED will illuminate and should be on at all times when the interface is on. The LED will also ash whenever
a SWC button is pressed
3. The interface comes pre-programmed for all of the vehicles factory SWC functions and does not require programming unless
you wish to re-assign the SWC functions to different buttons. The SWC can always be restored to default settings by pressing
and releasing the program button on the side of the interface once and waiting 7 seconds for the LED to ash 4 times.
Red / White P.B. Output (-)
Purple / White VSS Output
Blue / White Amp Turn On Input
Red Acc. Output (1 amp)
Orange / White Illum. Output (+)
Green Reverse Output (+)
Interface Connector
Yellow Battery +12v
Black Ground
Blue Antenna On Input
White Front L + input
White / Black Front L - input
Grey Front R + input
Grey / Black Front R - input
Green Rear L + input
Green / Black Rear L - input
Purple Rear R + input
Purple / Black Rear R - input
Vehicle Connector SWC Connector
Blu/Yel Kenwwod, Newer
JVC, OEM or
Blaupunkt
3.5mm Jack Alpine, JVC,
Clarion, Pioneer,
Sony, Valor, Boyo,
Dual, Visteon or
Advent
Accessory Output
+12volts 1amp max.
Interface Connector
See above chart for
wire color descriptions.
Vehicle Connector
See above chart for
wire color description.
SWC Connection
See above chart for
different radio type
connections
Wiring SWC Connection
Page 1
Pacic Accessory Corporation
® | Santa Ana, California 92705 | Ph. 866-931-8021 | support@pac-audio.com
©2011 Pacic Accessory Corporation
www.pac-audio.com
C
RP4-CH11
Radio Replacement & Steering Wheel Control Interface
for Chrysler/Dodge/Jeep Vehicles
Rev. 112811
Optional Steering Wheel Control Programming
IMPORTANT! The interface comes pre-programmed for all of the vehicles factory SWC functions and does not require programming
unless you wish to re-assign the SWC functions to different buttons. The SWC can always be restored to default settings by
pressing the program button on the side of the interface once and waiting for the timeout.
SET RADIO SELECT SWITCH
Installation Steps
1.The radio select rotary switch on the side of the interface must be adjusted to the proper radio
setting before plugging the interface into the vehicle (see page 2 for setting chart).
2. Only one of the two provided radio harnesses will be used. Remove the factory installed radio to determine the correct harness for your
particular vehicle.
3. Make all connections as described in the connection chart on page 1. Vehicles without a factory amplier: Connect the aftermarket radio’s
front and rear speaker wires to the vehicle connector. Vehicles with a factory amplier: The factory amplier only accepts two channels
of audio input (left and right). Connect the front outputs of the aftermarket radio to the rear inputs of the vehicle connector. This will allow
navigation voice prompts and Bluetooth calls to be heard. The rear speaker outputs of the aftermarket radio are not used. Fading is not
supported in this application. The factory amplier’s fading is controlled by data communication from the factory radio. Neither the aftermarket
radio or the RP interface have the ability to control the amplier’s fader.
4. Connect the SWC wire according to the chart on page 1 (aftermarket radio MUST support a wired remote input)
5. If you wish to reassign functions to the SWC follow the programming instructions in the next section.
If you wish to re-assign the SWC functions, the interface must be programmed in the specic order shown in the chart on the next
page. If you come across a function in the chart that your steering wheel does not have, or you do not want to program, press and
release the program button on the side of the interface to skip that function. The LED will ash off and on conrming that you have
successfully skipped that function and are ready to proceed to the next one.
SET RADIO SELECT SWITCH
Alpine
Advent,
BOYO, Dual,
Visteon, Sony
Blaupunkt Clarion JVC Kenwood OEM Pioneer Valor
1 7 8 4 2 3 6 7 5
1
2
3
4
5
6
7
8
9
0
SET RADIO SELECT SWITCH
Alpine
Advent,
BOYO, Dual,
Visteon, Sony
Blaupunkt Clarion JVC Kenwood OEM Pioneer Valor
1 7 8 4 2 3 6 7 5
1
2
3
4
5
6
7
8
9
0
Default SWC Button Assignments
Alpine JVC Kenwood Clarion
V
alo
r
OEM Sony/Pionee
r
Blaupunkt
olume + Volume + Volume + Volume + Volume + Volume + Volume + Volume + Volume +
V
olume - Volume - Volume - Volume - Volume - Volume - Volume - Volume - Volume -
Source Source Source Source Source Source Source Source Source
Track + Track + Track + Track + Search + Track + Next Track + Track +
Track - Track - Track - Track - Search - Track - Previous Track - Track -
Preset + Preset + Preset Disc/Radio + Band Mute Band Preset + Disc +
V
oice Mute Mute Mute Mute Cursor - Answer Mute Mute
Phone Receive Receive
A
nswe
r
Send/End Cursor + Hang Up
A
nswe
r
OK
Page 2

Produkt Specifikationer

Mærke: PAC
Kategori: Ikke kategoriseret
Model: RP4-CH11

Har du brug for hjælp?

Hvis du har brug for hjælp til PAC RP4-CH11 stil et spørgsmål nedenfor, og andre brugere vil svare dig


Ikke kategoriseret PAC Manualer

PAC

PAC OnStar OS-311b Manual

17 Februar 2025
PAC

PAC BT-SWC-NI1 Manual

11 Februar 2025
PAC

PAC OnStar OS-311 Manual

11 Februar 2025
PAC

PAC LCCH21 Manual

11 Februar 2025
PAC

PAC APSUB-TY13 Manual

28 December 2024
PAC

PAC RP4-GM31 Manual

6 September 2024
PAC

PAC NU-CTS2 Manual

6 September 2024
PAC

PAC TR7 Manual

6 September 2024
PAC

PAC OS-5 Manual

6 September 2024
PAC

PAC NDK735MG Manual

29 August 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

ORNO

ORNO OR-PSU-1675 Manual

15 Juni 2025
EmberGlo

EmberGlo ES5CTS Manual

15 Juni 2025
Chapin

Chapin 8201A Manual

15 Juni 2025
Gourmia

Gourmia GDK2365 Manual

15 Juni 2025
Xiaomi

Xiaomi Wireless Mouse 3 Manual

15 Juni 2025
Auray

Auray SVRK-12U-D Manual

15 Juni 2025
Aiphone

Aiphone IXGW-TGW Manual

15 Juni 2025
Aiphone

Aiphone AC-2DE Manual

15 Juni 2025
Schlage

Schlage S280 Manual

15 Juni 2025
Cleveland

Cleveland PGM3002 Manual

15 Juni 2025