PAC RP4-MZ11 Manual

PAC Ikke kategoriseret RP4-MZ11

Læs gratis den danske manual til PAC RP4-MZ11 (7 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 9 personer og har en gennemsnitlig bedømmelse på 4.3 stjerner ud af 5 anmeldelser. Har du et spørgsmål om PAC RP4-MZ11, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/7
RP4-MZ11
Radio Replacement & Steering Wheel Control Interface
for MazdaVehicles
Pacic Accessory Corporation
® | Santa Ana, California 92705 | Ph. 866-931-8021 | support@pac-audio.com
©2012 Pacic Accessory Corporation
www.pac-audio.com
Rev. 081612
C
Page 1
Introduction & Features
Important Notes
The RP4-MZ11 interface allows the replacement of a factory radio in select Mazda vehicles with MS-CAN radios. Using
this interface will retain factory features such as steering wheel controls (SWC), programming of the clock on the OEM
LCD screen, vehicle information on the OEM LCD screen and the BOSE amplier when the original radio is removed. The
RP4-MZ11 also provides data bus driven outputs such as retained accessory power (RAP), vehicle speed sensor (VSS),
illumination, reverse trigger and parking brake.
1. The radio select rotary switch on the side of the interface must be adjusted to the proper radio setting before plugging the
interface into the vehicle (see below for setting chart).
2. If using this interface in a Mazda CX-5, all vehicle settings must be nalized before removing the factory radio.
3. When the interface is rst plugged into the vehicle the LED will ash indicating that it is initializing. Once initialization is complete
the LED will illuminate and should be on at all times when the interface is on.
4. The following vehicles will not provide a VSS signal as this information is not on the data bus: RX-8, 2007-2009 CX-9 w/non-nav
radio, Miata
5. The following vehicles will not provide a reverse output as this information is not on the data bus: RX8, 2007-2009 CX7, 2010
Mazda 5, Miata
6. The following vehicles will not provide a parking brake output as this information is not on the data bus: RX-8, Miata
7. The following vehicles have a speed based parking brake wire that will provide a negative trigger until the vehicle is going at
least 4 mph: 2007-2009 CX-9, 2007-2009 CX-7
8. The LED will also ash whenever a SWC button is pressed
9. The interface comes pre-programmed for all of the vehicles factory SWC functions and does not require programming unless
you wish to re-assign the SWC functions to different buttons. The SWC can always be restored to default settings by pressing
and releasing the program button on the side of the interface once and waiting 7 seconds for the LED to ash 4 times.
10. The LED will ash whenever a SWC button is pressed.
Wiring Connection Chart
Red / White P.B. Output (-)
Purple / White VSS Output
Red Acc. Output (1 amp)
Green/ White 2nd SWC Input
(Connect to blue
wire in vehicle con-
nector in Mazda
CX-5, not used in
other applications)
Green Reverse Output (+)
Orange Illumination
Interface Connector
Yellow Battery +12v
Black Ground
Blue Antenna On Input
(connect to Green/
White wire in inter-
face connector in
the Mazda CX-5)
Orange/White Illumination
White Front L + input
White / Black Front L - input
Grey Front R + input
Grey / Black Front R - input
Green Rear L + input
Green / Black Rear L - input
Purple Rear R + input
Purple / Black Rear R - input
Vehicle Connector SWC Connector
Blu/Yel Kenwwod, Newer
JVC, OEM or
Blaupunkt
3.5mm Jack Alpine, JVC,
Clarion, Pioneer,
Sony, Fusion, Valor,
Boyo, Dual, Visteon
or Advent
RP4-MZ11
Radio Replacement & Steering Wheel Control Interface
for Mazda Vehicles
Pacic Accessory Corporation
® | Santa Ana, California 92705 | Ph. 866-931-8021 | support@pac-audio.com
©2012 Pacic Accessory Corporation
www.pac-audio.com
C
Rev. 081612
Page 2
Installation Steps
1.The radio select rotary switch on the side of the interface must be adjusted to the proper radio
setting before plugging the interface into the vehicle.
2. Make all connections as described in the chart on page 1. Connect the blue wire in the 24 pin vehicle harness to the 2013+ Mazda CX5 -
green/white wire in the 16-pin RP harness. This is necessary for the Bluetooth SWC to function with the aftermarket radio. This vehicle must
also use the orange/white wire in the Interface Connector.
3. Connect the SWC wire according to the chart on page 1 (aftermarket radio MUST support a wired remote input).
4. If you wish to reassign the SWC buttons to different functions follow the programming instructions in the next section.
SET RADIO SELECT SWITCH
Alpine
Advent,
BOYO, Dual,
Visteon, Sony
Blaupunkt Fusion OEMClarion JVC Kenwood Pioneer Valor
1 7 8 9 2 3 6 7 54
1
2
3
4
5
6
7
8
9
0
Illustration / Schematic
Pacific Accessory Corporation
Interface Connector
See above chart for
wire color descriptions.
Vehicle Connector
See above chart for
wire color description.
SWC Connection
See above chart for
different radio type
connections
Wiring SWC Connection
The interface comes pre-programmed for the functions listed in the chart below and does not require programming unless you
wish to re-assign the SWC functions to different buttons. The SWC can always be restored to default settings by pressing the
program button on the side of the interface once and waiting for the LED to ash four times.
Alpine JVC Kenwood Clarion
V
alo
r
OEM Sony/Pionee
r
Fusion Blaupunkt
V
olume + Volume + Volume + Volume + Volume + Volume + Volume + Volume + Volume + Volume +
olume - Volume - Volume - Volume - Volume - Volume - Volume - Volume - Volume - Volume -
Mode Source Source Source Source Source Source Source Source Source
Track + Track + Track + Track + Search + Track + Next Track + Track + Track +
Track - Track - Track - Track - Search - Track - Previous Track - Track - Track -
V
oice/Mute Mute Mute Mute Mute Mute Mute Mute Mute Mute
Answe
r
Receive Receive Answer Send Cursor + Answer Answer Audio Disc +
End End Selec
t
Pla
y
End OK Hang Up Phone Menu Powe
r
OK
Optional Steering Wheel Control Programming
Default SWC Button Assignments

Produkt Specifikationer

Mærke: PAC
Kategori: Ikke kategoriseret
Model: RP4-MZ11

Har du brug for hjælp?

Hvis du har brug for hjælp til PAC RP4-MZ11 stil et spørgsmål nedenfor, og andre brugere vil svare dig


Ikke kategoriseret PAC Manualer

PAC

PAC CAM-GM51 Manual

11 Juli 2025
PAC

PAC TY1A-RS Manual

11 Juli 2025
PAC

PAC SR-F15009HX Manual

10 Juli 2025
PAC

PAC SRK-RAM13HX Manual

10 Juli 2025
PAC

PAC AAI-TY3 Manual

30 Juni 2025
PAC

PAC SRK-GM14HX Manual

10 Marts 2025
PAC

PAC C2A-CHY Manual

19 Februar 2025
PAC

PAC MCI-FD22 Manual

19 Februar 2025
PAC

PAC GM6A-RST Manual

19 Februar 2025
PAC

PAC SWI-X Manual

19 Februar 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Navman

Navman MY500XT Manual

1 August 2025
Navman

Navman FOCUS150 GPS Manual

1 August 2025
Scheppach

Scheppach TW1000 Manual

1 August 2025
Navman

Navman MiVue 750 WIFI Manual

1 August 2025
Navman

Navman MiVue Drive FHD Manual

1 August 2025
Midea

Midea MEC64 Manual

1 August 2025
Navman

Navman MY50T Manual

1 August 2025
Navman

Navman M100 Manual

1 August 2025
Navman

Navman MiVue 770 SAFETY Manual

1 August 2025
Navman

Navman MiVue 790 Manual

1 August 2025