PAC RP4-NI11 Manual

PAC Ikke kategoriseret RP4-NI11

Læs gratis den danske manual til PAC RP4-NI11 (9 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 21 personer og har en gennemsnitlig bedømmelse på 4.8 stjerner ud af 11 anmeldelser. Har du et spørgsmål om PAC RP4-NI11, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/9
RP4-NI11
Finding an Accesory 12v+
in 2014+ Nissan Rogue With a Navigation radio
Pacic Accessory Corporation
® | Santa Ana, California 92705 | Ph. 866-931-8021 | support@pac-audio.com
©2013 Pacic Accessory Corporation
www.pac-audio.com
Rev. 011116
C
Page 1
Tech Bulletin
Important Notes
Illustration / Schematic
When installing the RP4-NI11 into a 2014+ Nissan Rogue it may be necessary to make a hardwired connection for accessory
power. This is necessary due to these vehicles having a different location for the 12v accessory wire. Please follow the procedure
outlined below to make the proper connection.
1. This tech bulletin only needs to be followed if installing the RP4-NI11 into the 2014+ Nissan Rogue without an accessory wire in the main
20-pin harness.
2. It is important that all connections be soldered to ensure they are secure. Using T-Taps or crimp connectors will result in faulty connections
which could cause erratic/unreliable operation.
Installation Steps
1. Connect the main 20-pin and 24-pin harnesses as outlined in the instruction manual included with the interface.
2. Locate the light green accessory wire in the 24-pin Nissan factory harness (Fig. 1). This wire will need to be jumped to the red wire located in
pin 16 of the 20-pin RP4 harness (Fig 2).
RP4-NI11
Connector
Fig. 1
24-Pin Vehicle
Connector
Fig. 2
All connectors are viewed from wire side
Factory ACC Wire RP4 ACC Wire
© 2018 AAMP Global. All rights reserved. PAC is a Power Brand of AAMP Global.
PAC-audio.com
C
Page 1
Rev. 061118
Nissan Murano with Navigation
RP4-NI11 Hardwire
Technical Bulletin
Overview:
In order for the RP4-NI11 to operate in the 2015 and up Nissan Murano applications that are equipped with
navigation, several wires from the RP4-NI11 must be hardwired into the 40 pin harness at the radio. RP4-NI11
Revision 4 or higher of rmware is required.
Installation:
1. Follow the instructions from the
RP4-NI11 installation manual for the
wire connections from the RP4-NI11
into the aftermarket radio harness.
Only the primary 24 pin connector
and the black 16 pin RP4-NI11
connectors will be used (see Fig.1).
2. Cut the Pink (CAN +) and
Pink / Black (CAN -) wires between
the RP4-NI11 connector and where
the wires split to go to the 3 unused
connectors (see Fig. 1).
3. Connect the Pink wire (from step
2) to the Light Blue wire (CAN +) in
pin 41 of the 40 pin radio connector
(see Fig. 2).
4. Connect the Pink / Black wire (from
step 2) to the Light Green wire
(CAN -) in pin 21 of the 40 pin radio
connector (see Fig. 2).
5. Only necessary when using a
reverse camera: Locate the Green
(Reverse +) wire in the Black 16
pin RP4-NI11 connector that goes
to a junction near the (unused) 24
pin connector, with one side going
to the aftermarket radio wiring, one
side going to the (unused) 24 pin
connector, and one side going to the
(unused) 32 pin connector. Cut the
Green wire between the junction and
Cut for Non-Bose systems
Cut Pink and
Pink / Black
Cut Green
X
X
X
These Connectors
Not Used
This Connector
Is Used
Fig. 1
the (unused) 32 pin connector (see Fig. 1).
6. Connect the Green wire (from step 3) to the Green wire (Reverse +) in pin 45 of the 40 pin radio connector (see
Fig. 2).
Fig. 2
Connector Viewed From Wire Side
CAN - (Light Green) Rev + (Green)Pin 21 Pin 45
CAN + (Light Blue)Pin 41
Testing and Verication:
1. Turn on the ignition and press audio steering wheel control buttons to verify the LED on the RP4 NI11 ashes
to indicate that it recognizes the button commands. If the LED does not ash, verify the CAN + and CAN -
connections to the Pink and Pink / Black wires on the RP4-NI11, and verify the RP4-NI11 is using rmware
Revision 4 or higher.
2. Test the Green reverse output connector by verifying the wire is providing a 12 volt output when the ignition is on
and the vehicle is in reverse.

Produkt Specifikationer

Mærke: PAC
Kategori: Ikke kategoriseret
Model: RP4-NI11

Har du brug for hjælp?

Hvis du har brug for hjælp til PAC RP4-NI11 stil et spørgsmål nedenfor, og andre brugere vil svare dig


Ikke kategoriseret PAC Manualer

PAC

PAC OnStar OS-311b Manual

17 Februar 2025
PAC

PAC BT-SWC-NI1 Manual

11 Februar 2025
PAC

PAC OnStar OS-311 Manual

11 Februar 2025
PAC

PAC LCCH21 Manual

11 Februar 2025
PAC

PAC APSUB-TY13 Manual

28 December 2024
PAC

PAC RP4-GM31 Manual

6 September 2024
PAC

PAC NU-CTS2 Manual

6 September 2024
PAC

PAC TR7 Manual

6 September 2024
PAC

PAC OS-5 Manual

6 September 2024
PAC

PAC NDK735MG Manual

29 August 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Vulcan

Vulcan 1024W Manual

15 Juni 2025
Backyard Pro

Backyard Pro 554PL2030 Manual

15 Juni 2025
Haier

Haier 1U18TE2HDA Manual

15 Juni 2025
AEG

AEG EWKEXT1 Manual

15 Juni 2025
Planet

Planet XGPN-400AXV Manual

15 Juni 2025
Cadac

Cadac 3 Cook Turbo Manual

15 Juni 2025
Bobrick

Bobrick B-3944 Manual

15 Juni 2025
Sony

Sony SZC-4008 Manual

15 Juni 2025
Watts

Watts ETX-15 Manual

15 Juni 2025
Sigma

Sigma REMOTE ONE Manual

15 Juni 2025