PAC RP5-GM32 Manual

PAC Ikke kategoriseret RP5-GM32

Læs gratis den danske manual til PAC RP5-GM32 (5 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 13 personer og har en gennemsnitlig bedømmelse på 4.7 stjerner ud af 7 anmeldelser. Har du et spørgsmål om PAC RP5-GM32, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/5

RP5-GM32

Radio Replacement & Steering Wheel Control Interface

with OnStar Retention for General Motors Vehicles

Pacic Accessory Corporation

® | Santa Ana, California 92705 | Ph. 866-931-8021 | support@pac-audio.com

www.pac-audio.com

Rev. 091613

Introduction & Features

Important Notes

Wiring Connection Chart

Illustration / Schematic

The RP5-GM32 interface allows the replacement of a factory radio in select General Motors vehicles with 29-bit LAN

radios. Using this interface will retain factory features such as OnStar, steering wheel controls (SWC), warning chimes,

Rear Seat Controls (RSC) and the BOSE amplier when the original radio is removed. Use of this interface also allows

you to program two radio functions to each SWC button by using short press long press dual command functionality.

The RP5-GM32 also provides data bus driven outputs such as retained accessory power (RAP), vehicle speed sensor

(VSS), illumination, reverse trigger and parking brake.

1. The radio select rotary switch on the side of the interface must be adjusted to the proper radio setting before plugging the

interface into the vehicle (see next page for setting chart).

2. The interface comes pre-programmed for all of the vehicles factory SWC functions and does not require programming unless

you wish to re-assign the SWC functions or utilize short press long press dual command functionality. The SWC can always be

restored to default settings by following the procedure outlined on page 3.

3. RSC buttons that are identical to the SWC will mimic the SWC one for one.

4. The LED will ash whenever a SWC button is pressed.

Aftermarket Radio Connectioons

Yellow Battery +12v

Black Ground

Red Accessory Output

White Front L + input

White / Black Front L - input

Grey Front R + input

Grey / Black Front R - input

Green Rear L + input

Green / Black Rear L - input

Purple Rear R + input

Purple / Black Rear R - input

SWC Connector

Blu/Yel Kenwwod, Newer

JVC

3.5mm Jack Alpine, JVC,

Clarion, Pioneer,

Sony, Fusion, Boyo,

Dual, Lightning

Audio, Visteon or

Advent

SWC Connection

See above chart for

different radio type

connections

Wiring SWC Connection

Page 1

Aftermarket

Radio

Connections

Vehicle

Connections

Red / White Parking Brake

Output (-)

Purple / White Vehicle Speed

Output

Blue / White Not Used

Blue Not Used

Orange / White Illumination Output

(+)

Green Reverse Output (+)

Brown Loop Mute Loop - See

installation note 7

RP5-GM32

Radio Replacement & Steering Wheel Control Interface

with OnStar Retention for General Motors Vehicles

Pacic Accessory Corporation

® | Santa Ana, California 92705 | Ph. 866-931-8021 | support@pac-audio.com

www.pac-audio.com

Rev. 091613

Installation Steps

1. The radio select rotary switch on the side of the interface must be adjusted to the proper radio

setting before plugging the interface into the vehicle.

2. Make all connections as described in the chart on page1.

3. Factory installed ampliers will determine the audio output connection. If the vehicle has a factory installed amplier use the factory

amplier audio location. If a factory installed amplier is not present use the non-amplied factory audio location.

4. If the vehicle is equipped with a Premium BOSE system, connect the subwoofer and center channel RCA inputs to the aftermarket radios.

If the aftermarket radio to be installed does not have a dedicated center channel or sub output do not use this cable. To ensure best sound

performance channel summing is not recommended. Use this cable according to the outputs that are available.

5. If the vehicle is equipped with a reverse camera and the aftermarket radio has a reverse camera input, connect the yellow RCA plug on the

gray connector to the aftermarket radios reverse camera input.

6. Plug the CMX chime module in if necessary (If the vehicle chimes when the radio is removed the CMX is not necessary). PLEASE NOTE:

In order to get the best possible sound out of the CMX please mount it in a place free and clear of any obstructions, preferably as close as

possible to the bottom of the dash pointing down toward the oor of the vehicle.

7. The Mute loop (if not cut) will turn the accessory output off when an OnStar or Bluetooth call is made or received. If the aftermarket radio

has a mute input cut this loop and connect the outer brown wire to the mute input.

8. Connect the SWC wire according to the chart on page 1 (aftermarket radio MUST support a wired remote input).

9. If you wish to reassign functions to the SWC follow the programming instructions in the next section.

Optional Steering Wheel Control Programming

Page 2

Alpine Fusion Pioneer/Sony/OtherClarion JVC Kenwood

1 9 2 3 74

Other = Advent, BOYO, Dual, Lightning Audio, Visteon,

SET RADIO SELECT SWITCH

Alpine Fusion Pioneer/Sony/OtherClarion JVC Kenwood

1 9 2 3 74

Other = Advent, BOYO, Dual, Lightning Audio, Visteon,

SET RADIO SELECT SWITCH

IMPORTANT! The interface comes pre-programmed for the functions listed in the chart below and does not require programming

unless you wish to re-assign the SWC functions to different buttons. The SWC can always be restored to default settings by

following the procedure outlined on page 3.

Alpine JVC Kenwood Clarion Sony/Pionee

Fusion

olume + Volume + Volume + Volume + Volume + Volume + Volume +

olume - Volume - Volume - Volume - Volume - Volume - Volume -

Source Source Source Source Source Source Source

Track + Track + Track + Track + Search + Track + Track +

Track - Track - Track - Track - Search - Track - Track -

oice Mute Mute Mute Mute Mute Mute

Play/Pause Preset + Preset/Disc - Disc/FM+ Band Preset +

udio

Default Steering Wheel Control Programming

Default SWC Button Assignments

If you wish to re-assign the SWC functions, utilize short press long press dual command functionality or select between Factory/

Aftermarket mode, the interface must be programmed in the specic order shown in the chart on page 3. If you come across a

function in the chart that your steering wheel does not have, or you do not want to program, press and release the program button

on the side of the interface to skip that function. The LED will ash off and on conrming that you have successfully skipped that

function and are ready to proceed to the next one.

Produkt Specifikationer

Mærke:	PAC
Kategori:	Ikke kategoriseret
Model:	RP5-GM32

Har du brug for hjælp?

Hvis du har brug for hjælp til PAC RP5-GM32 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret PAC Manualer

PAC CAM-GM51 Manual

11 Juli 2025

PAC TY1A-RS Manual

11 Juli 2025

PAC SR-F15009HX Manual

10 Juli 2025

PAC SRK-RAM13HX Manual

10 Juli 2025

PAC AAI-TY3 Manual

30 Juni 2025

PAC SRK-GM14HX Manual

10 Marts 2025

19 Februar 2025

19 Februar 2025

19 Februar 2025

19 Februar 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Advantech MIC-3811 Manual

30 Juli 2025

Intermatic EI230W Manual

30 Juli 2025

Rockboard LED Light V2 Manual

30 Juli 2025

Advantech USB-5817 Manual

30 Juli 2025

Electro Harmonix 9DC-100 Manual

30 Juli 2025

Advantech UTC-515H Manual

30 Juli 2025

Extron MGP 641 xi 5K Manual

30 Juli 2025

Festo EMME-AS-80-M-LS-AMB Manual

30 Juli 2025

Tiptop Audio Octogain Manual

30 Juli 2025

Artec SE-ADL Manual

30 Juli 2025