PAC TATO Manual

PAC Ikke kategoriseret TATO

Læs gratis den danske manual til PAC TATO (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 26 personer og har en gennemsnitlig bedømmelse på 4.4 stjerner ud af 13.5 anmeldelser. Har du et spørgsmål om PAC TATO, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

Pacic Accessory Corporation - Santa Ana, CA 92705

866-931-8021 • www.pac-audio.com

DISCLAIMER: Under no circumstances shall the manufacturer or the distributors of the TATO be held liable for consequential damages sustained in

connection with the TATO. The manufacture and it’s distributors will not, nor will they authorize any representative or any other individual to assume

obligation or liability in relation to the TATO other than its replacement.

06-29-10

J1850

Class 2

VPW

Class 2

J1850

100011101111001001101100

1110100 0011011 0111001100

Arbitration

EOD

CRC

100011101111001001101100

1110100 0011011 0111001100

Class 2

J1850

TATO

JBL Amplier Turn-On Interface for

Toyota CANbus Vehicles

The TATO is designed to control the power and audio levels of the factory installed

JBL amplier allowing the OEM radio to be removed and replaced with an aftermarket

stereo.

Installation:

Note: BEFORE REMOVING THE FACTORY RADIO: BALANCE AND FADE IT TO THE CENTER, TURN THE

RADIO UP TO AT LEAST 3/4 VOLUME, TURN THE RADIO OFF, TURN THE IGNITION OFF & THEN PROCEED

WITH REMOVING THE FACTORY RADIO

Disconnect the factory radio from the OEM wiring harness and remove it from the vehicle. Make the

following connections of the TATO wiring harness to the aftermarket radio:

Connections:

Yellow Wire - Connect to 12 Volt Constant Power on aftermarket radio•

Red Wire - Connect to Accessory on aftermarket radio•

Black Wire - Connect to Ground on aftermarket radio•

Orange/White Wire - Connect to Dimmer on aftermarket radio•

*11 Pin Harness - Connect to PAC’s SWI-X, SWI-JACK, SWI-PS or SWI-ECL2 (Sold Separately) •

Red Bullet Connector - Connect to Accessory

Black Bullet Connector - Connect to Ground

Connect the 4 RCA connectors to the RCA outputs of the aftermarket radio •

Front Left - White RCA Front Right - Grey RCA

Rear Left - Green RCA Rear Right - Purple RCA

If connecting the TATO to a head unit with only 2 Channel RCA outputs, use two pairs of RCA splitters (1M-2F) to split the signal. Failure to connect all 4 inputs

of the TATO will result in loss of audio performance. Fade audio controls will only function with a 4 channel aftermarket deck.

Connections to the TATO Interface:

Connect 24-pin translucent connector •

to the side of the TATO.

Connect 8-pin DIN cable to the plug on •

the side of the TATO.

Connections to the Vehicle:

Plug the main 20-pin Toyota harness into the matching factory wir-•

ing harness.

*• If using PAC’s SWI-X, SWI-JACK, SWI-PS or SWI-ECL2, Plug

the smaller 20-pin harness into the matching factory wiring har-

ness. Program PAC’s SWI-X, SWI-JACK, SWI-PS or SWI-ECL2

for version #8 and follow the programming instructions included

with PAC’s SWI-X, SWI-JACK, SWI-PS or SWI-ECL2.

Pacic Accessory Corporation - Santa Ana, CA 92705

866-931-8021 • www.pac-audio.com

DISCLAIMER: Under no circumstances shall the manufacturer or the distributors of the TATO be held liable for consequential damages sustained in

connection with the TATO. The manufacture and it’s distributors will not, nor will they authorize any representative or any other individual to assume

obligation or liability in relation to the TATO other than its replacement.

06-29-10

Warranty:

One Year Limited Warranty

The quality controls used in the manufacture of this product will ensure your satisfaction. This warranty applies only to the original purchaser of this prod-

uct from an authorized Pacic Accessory Corporation dealer. This warranty covers any supplied or manufactured parts of this product that, upon inspec-

tion by Pacic Accessory Corporation authorized personnel, is found to have failed in normal use due to defects in material or workmanship. This war-

ranty does not apply to installation expenses. Attempting to service or modify this unit, operating this unit under conditions other than the recommended

voltage will render this WARRANTY VOID. Unless otherwise prescribed by law, Pacic Accessory Corporation shall not be liable for any personal injury,

property damage and or any incidental or consequential damages of any kind (including water damage) resulting from malfunctions, defects, misuse,

improper installation or alteration of this product.

All parts of this Pacic Accessory Corporation product are guaranteed for a period of 1 year as follows: Within the rst 12 months from date of pur-

chase, subject to the conditions above, Pacic Accessory Corporation will repair or replace the product at their discretion, if it is defective in material or

workmanship providing it is returned to an Authorized Pacic Accessory Corporation Dealer, with PROOF OF PURCHASE from an authorized Pacic

Accessory Corporation dealer.

Warning:

This equipment may be reset by unintentional electrostatic discharge during operation. Exposure to direct sunlight or extreme heat may cause damage

or malfunction.

FCC Class B Radio Frequency

Interference Statement:

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of FCC rules. These limits are de-

signed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio

frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However,

there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television

reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the

following measures:

1. Re-orientate or relocate the receiving antenna.

2. Increase the separation between the equipment and receiver.

3. Connect the equipment into an outlet on a circuit different from that of which the receiver is connected.

4. Consult the dealer or an experienced radio / television technical for help

Notice : The changes or modications not expressly approved by the party responsible for compliance could void the user authority to operate the equip-

ment.

Adjusting Volume Output:

When initially connecting the TATO to the vehicle the

max output might not meet that of the factory radio.

If the volume is low you can adjust the output using

the dip switches on the side of the module. It is rec-

ommended to use a 4 volt RMS capable aftermarket

radio. When adjusting the gain output it is recom-

mended to start with the plus 7dB setting and working

your way down.

Note: It may take up to 10 seconds before the gain

adjustment is heard.