Schneider MTN647091 Manual

Schneider Ikke kategoriseret MTN647091

Læs gratis den danske manual til Schneider MTN647091 (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 21 personer og har en gennemsnitlig bedømmelse på 4.9 stjerner ud af 11 anmeldelser. Har du et spørgsmål om Schneider MTN647091, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

V6470-561-02 11/21

MTN64709 1© Merten2009V6470-561-0211/21

The control unit 0-10 V REG-K/1-gang with manual

mode (refered to below as control unit) dims and

switches fluorescent lamps using electronic ballasts with

a 0-10 V/1-10 V interface and LV halogen lamps using

transformers with a 0-10 V/1-10 V interface.

|The control voltage range can be set with the ETS

via a parameter.

You can also manually switch the connected loads with

the manual switch on the control unit without bus volt-

age.

The control unit has a bus coupler. It is installed on a DIN

rail TH 35 according to EN 60715, with the bus connec-

tion made via a bus connecting terminal. A data rail is not

required.

SpaceLogic KNX Control unit 0-10 V

REG-K/1-gang with manual mode

Operating instructions

Art. no. MTN647091

For your safety

HAZARD OF ELECTRIC SHOCK, EXPLOSION, OR

ARC FLASH

Safe electrical installation must be carried out only by

skilled professionals. Skilled professionals must prove

profound knowledge in the following areas:

• Connecting to installation networks

• Connecting several electrical devices

• Laying electric cables

• Connecting and establishing KNX networks

• Safety standards, local wiring rules and regulations

Failure to follow these instructions will result in

death or serious injury.

The device may be damaged!

• Always operate the product in compliance with the

specified technical data.

• Only install devices with at least basic insulation next

to the device.

Failure to follow these instruction can result in

equipment damage.

Getting to know the control unit

A Bus connecting terminal

B Programming-LED (red)

C Programmier button

D Cable cover

E Operating-LED „RUN“ (green)

F Manual switch

G Channel terminals for load voltage

HOutputs 1–10 V

1 Set the control unit onto the DIN rail.

2 Connect KNX.

¼WARNING

Risk of death from electric shock. The device

can become damaged.

Safety clearance must be guaranteed in accord-

ance with IEC 60664--1. There must be at least 4

mm between the individual cores of the 230 V

supply cable and the KNX line A.

¼WARNING

Risk of death from electric shock. The device

could become damaged.

Disconnect the mains voltage before connecting

the device to the load.

Terminals may not be inserted under load.

Connections, displays and operating

elements

Mounting the control unit

1 2

5 mm

230 V

4 mm

¼DANGER

Risk of death from electric shock.

Voltage may be present at the outputs when the

mains voltage is connected to the system.

If subjected to strong vibrations during transpor-

tation, the switch contacts might change to the

enabled state.

After connecting the bus voltage, set the relays of

the channels to the position desired simply by

switching „On/Off“ or by changing the manual

switch to „OFF“.

3 Connect the bus voltage.

4 Connect the load.

5 Connect the load voltage.

1 Press the programming button.

The programming-LED lights up.

2 Load the physical address and application into the

device from the ETS.

The programming LED goes out.

The operation LED lights up: The application was loaded

successfully, the device is ready for operation.

A Control unit

B Electronic ballast with 0-10 V / 1-10 V inter-

face

C Fluorescent lamp

D Eletronic transformer with 0-10 V / 1-10 V con-

trol input

E LV halogen lamps

F to other devices with 0-10 V / 1-10 V interface

Putting the control unit into operation

KNX

+ -

NL1

0-10V

12V AC

0-10V

16 A

Produkt Specifikationer

Mærke:	Schneider
Kategori:	Ikke kategoriseret
Model:	MTN647091

Har du brug for hjælp?

Hvis du har brug for hjælp til Schneider MTN647091 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Schneider Manualer

Schneider TeSys D LR97D25 Manual

5 November 2025

Schneider Homeline HOM250PSPD Manual

4 November 2025

Schneider BC650-RSX761 Manual

7 Oktober 2025

Schneider P8VNTG Manual

1 Oktober 2025

Schneider QCGK3 Manual

1 Oktober 2025

Schneider Altivar 61 VW3A3319 Manual

1 Oktober 2025

Schneider Altivar 312 VZ3V3103 Manual

1 Oktober 2025

Schneider SCTK30 Manual

1 Oktober 2025

Schneider Altivar 71 VW3A7201 Manual

1 Oktober 2025

Schneider OHBS Manual

1 Oktober 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Scott Essential 09989 Manual

5 November 2025

BlueShape Granite Link AP Manual

5 November 2025

EtherWAN OttoE 10H Manual

5 November 2025

Infiniton Belcanto49C1 Manual

5 November 2025

Intermatic WP1250MXD Manual

5 November 2025

INIU P63-P1 Manual

5 November 2025

D'Addario PW-XPND-01 Manual

5 November 2025

DS18 VOC8PRO Manual

5 November 2025

Icron Rover 2850 Manual

5 November 2025

Amaran Peak Manual

5 November 2025