SIIG CE-MT0212-S1 Manual

SIIG Wandstøtte CE-MT0212-S1

Læs gratis den danske manual til SIIG CE-MT0212-S1 (8 sider) i kategorien Wandstøtte. Denne vejledning er vurderet som hjælpsom af 33 personer og har en gennemsnitlig bedømmelse på 5.0 stjerner ud af 17 anmeldelser. Har du et spørgsmål om SIIG CE-MT0212-S1, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/8

Caution

A B C D E F G

04-0527C

Full-Motion LCD/TV Monitor Mount - 10" to 24"

Installation Instructions

(x2) M6X60

bolt

(x2) M6 concrete

anchor

(x4) M6 small

washer

(x2) M6 large

washer

(x4) M4X12

screw

(x4) M5X12

screw

Tools Required: Electronic stud finder, #2 Phillips head screw driver, drill, 1/8" drill bit (wood stud installation), 5/16" masonry

drill bit (concrete/brick wall installation).

Do not install near heater, fireplace, air conditioning, in direct sunlight, or any other heat producing source.

Failure to do so may result in damage to the display and could increase the risk of fire.

The wall structure must be capable of supporting at least the maximum load capacity as indicated. If not, the

wall must be reinforced. Proper installation procedure by yourself or a qualified service technician, as outlined in

the installation instructions, must be adhered to. Failure to do so could result in serious personal injury.

When mounting to a wall that contains wood studs, confirm dead center of the wood stud prior to installation, it

is recommended that the wood studs be a minimum of 16" apart.

It is recommended that two people perform the installation. Injury and/or damage can result from dropping or

mishandling the display.

(x4) M6X12

screw

Prior to the installation of this product, the installation instructions should be read and completely understood.

The installation instructions must be read to prevent personal injury and property damage. Keep these

installation instructions in an easily accessible location for future reference.

CAUTION: The maximum load capacity is 33 lbs (15kg). Use with products exceeding the maximum load

capacity may cause serious injury. See apparatus instructions.

Recommended mounting surfaces: wood stud and solid-flat concrete. If the mount is to be installed on any

surface other than wood studs, use suitable hardware (not included but commercially available) .

Hardware Kit

Do not install on a structure that is prone to vibration, movement or chance of impact. Failure to do so could

result in damage to the display and/or damage to the mounting surface.

Take down the plate and drill two 2" deep holes, using a 1/8" drill bi

at the position you'v

marked.

Hold the wall plate to the wall, use the two mounting holes to mark the locations to be used for

mounting the wall plate.

Step 2: Display Plate Installation

Position the wall plate onto the wall again and insert the bolts (A) and washer (D) into the

anchor as shown (figure 1-c) and tighten.

Place your TV screen down on a soft, flat surface, and locate the threaded mounting points

that are located on the back of the display.

Attach the wall plate to the wall again and insert the bolts (A) and washers (D) into the holes

and tighten (figure 1-b).

Use a high-quality electronic stud finder (commercially available) to locate dead center of a

stud and mark the location with a pencil (figure 1-a).

Hold the wall plate (figure 1-c) to the wall, use the two mounting holes to mark the locations to

be used for mounting the wall plate. Locate the holes directly into the brick, block or concrete,

never into the mortar between the blocks.

Step 1: Wall Plate Installation

Wood Stud Installation

Pre-drill two holes to a depth of 2" using a 3/8" masonry drill bit at the positions you've marked

and insert one concrete anchor (B) into each hole.

According to the size of the display's hole, choose the corresponding screw (E/F/G) and

washer (C) and insert into the hole as shown (figure 2-a) and tighten.

Concrete/Brick Wall Installation

Produkt Specifikationer

Mærke:	SIIG
Kategori:	Wandstøtte
Model:	CE-MT0212-S1
Bredde:	14 mm
Dybde:	12 mm
Højde:	26.5 mm
Vægt:	1150 g
Produktfarve:	Sort
Certificering:	VESA
Monteringstype:	Væg
Drejevinkel område:	15 °